Table of Contents
Advertisement
Chapter 14
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Verify the memory upgrade on the standby RP by running the following commands:
Step 5
Router# configure terminal
Router(config-red)# redundancy
Router(config-r-mc)# main-cpu
Router(config-r-mc)# standby console enable
Router(config-r-mc)# end
Router-stby# show version
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental
Version 15.2(20111220:221816) [v152_2_s_xe36_throttle-tozhang-xe36_ios 114]
.
.
.
cisco ASR1006 (RP1) processor with 1689519K/6147K bytes of memory.
Processor board ID FOX1224G4VX
20 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
955063K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
.
.
.
Use the redundancy force-switchover command to switch the upgraded standby RP to the active state.
Step 6
The RP that was in the active state moves to the standby state.
Repeat Step 1 through Step 5 on the standby RP.
Step 7
Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
The Cisco ASR1000-RP1 module memory interface supports two DDR-II SDRAM MiniDIMMs with
ECC protection.'
Unlike the Cisco ASR 1006, ASR 1004, and ASR 1013 routers, the DIMM memory interface is not
Note
field-replaceable on the Cisco ASR 1002 router.
'This section provides instructions for removing and replacing the Cisco ASR1000-RP1 Mini DIMM
memory modules.
The Cisco ASR 1000 Series RP memory spares are sold as pairs. For example, the 2 GB memory spare
Note
(M-ASR1K-RP1-2GB=) is sold as a pair of 1 GB modules and the 4 GB memory spare
(M-ASR1K-RP1-4GB=) is sold as a pair of 2 GB modules. Memory repairs or upgrades must utilize the
complete memory pairs as shipped from Cisco. For example, if 1 of the 2 memory modules were to fail
on the Cisco ASR 1000route processor, then both memory modules must be removed and replaced with
a spare memory pair (as shipped from Cisco) and the failing memory should be returned as a pair to
Cisco.
To prevent the system from operating incorrectly, do not mix modules from different vendors. The
modules might not be compatible with each other.
OL-13208-11
Removing and Replacing the Cisco ASR 1000 Series DIMM Memory Modules
Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide
14-19
Advertisement
Chapters
Table of Contents
Troubleshooting
Related Manuals for Cisco ASR 1000 series
Related Products for Cisco ASR 1000 series
- Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1 Router
- Cisco ASR1000-RP2 - ASR 1000 Series Route Processor 2 Router
- Cisco ASR-1000-SIP10
- Cisco ASR 1001
- Cisco ASR1002-5G-SEC/K9 - ASR 1002 VPN+FW Bundle Router
- Cisco ASR1004-20G-SEC/K9 - ASR 1004 VPN+FW Bundle Router
- Cisco ASR1002-10G-VPN/K9 - ASR 1002 VPN Bundle Router
- Cisco ASR1002-5G-HA/K9 - ASR 1002 HA Bundle Router