Powering Up The Replaced Fabric Card - Cisco CRS-1 - Carrier Routing System Router Migration Manual
Carrier routing system
Hide thumbs
Also See for CRS-1 - Carrier Routing System Router:
- Administration manual (436 pages) ,
- Getting started manual (289 pages) ,
- Troubleshooting manual (264 pages)
Table of Contents
Advertisement
Downgrading your Cisco CRS-3 Carrier Routing System 16-Slot Line Card Chassis Back to a Cisco CRS-1 Carrier Routing
System 16-Slot Line Card Chassis
•
•
•
•
Use the Status LEDs, located on the CRS-1 fabric card faceplate, to verify the correct installation of the
CRS-1 fabric card:
•
•
Prerequisites
RP/0/RP0/CPU0:router#admin
RP/0/RP0/CPU0:router(admin)#config
RP/0/RP0/CPU0:router(admin-config)#hw-module power disable loc 0/SM0/SP
RP/0/RP0/CPU0:router(admin-config)#commit
RP/0/RP0/CPU0:router(admin)#show platform
Node
<snip>
0/SM0/SP
0/SM1/SP
0/SM2/SP
0/SM3/SP
0/SM4/SP
0/SM5/SP
0/SM6/SP
0/SM7/SP
<snip>
Powering up the Replaced Fabric Card
This section describes how to enable power back to the Fabric node, and verify that node is moved to
Powered state.
SUMMARY STEPS
1.
2.
3.
4.
Cisco CRS-1 Carrier Routing System to Cisco CRS-3 Carrier Routing System Migration Guide
2-14
Chapter 2
Downgrading Your Cisco CRS-3 Carrier Routing System Router Back to a Cisco CRS-1 Carrier Routing
Make sure that the card is seated firmly in the Cisco CRS Fabric Card Chassis slot. One easy way
to verify physical installation is to see whether the front faceplate of the CRS-1 fabric card is even
with the fronts of the other cards installed in the card cage.
Check whether the ejector levers are latched and that the captive screws are fastened properly. If you
are uncertain, unlatch the levers, loosen the screws, and attempt to reseat the CRS-1 fabric card.
Examine the Cisco CRS Fabric Card Chassis alarm module to see if there are any active alarm
conditions. (See the section on the alarm module in Cisco CRS Carrier Routing System 16-Slot Line
Chassis System Description.)
Examine the Cisco CRS Fabric Card Chassis power shelves to see whether the chassis, as a whole,
is receiving power.
When the CRS-1 fabric card is properly installed, the Status LED turns green. If this LED is off,
verify that the CRS-1 fabric card is installed correctly.
If there is a failure during the board boot sequence, the two four-digit alphanumeric LED displays
indicate the current boot phase to assist you in debugging the board failure.
Type
FC/S(SP)
FC/S(SP)
FC/S(SP)
FC/S(SP)
FC/S(SP)
FC/S(SP)
FC/S(SP)
FC/S(SP)
admin
configure
no hw-module power disable loc 0/SM0/SP
commit
PLIM
State
N/A
UNPOWERED
N/A
IOS XR RUN
N/A
IOS XR RUN
N/A
IOS XR RUN
N/A
IOS XR RUN
N/A
IOS XR RUN
N/A
IOS XR RUN
N/A
IOS XR RUN
System Router
Config State
PWR,NSHUT,MON
PWR,NSHUT,MON
PWR,NSHUT,MON
PWR,NSHUT,MON
PWR,NSHUT,MON
PWR,NSHUT,MON
PWR,NSHUT,MON
PWR,NSHUT,MON
OL-13669-03
Advertisement
Chapters
Table of Contents
