Table of Contents
Advertisement
C. Registering the Number of Punch Hole
Perform the following to register the type of puncher unit (number of
holes) used to the IC on the punch controller PCB for identification by the
finisher. Be sure to register the type whenever you have replaced the
punch controller PCB.
1) Set bits 1 through 4 on the DIPSW1001 on the punch controller PCB
as follows:
ON
1
Fig.F05-102-02
2) Press SW1002 on the punch controller PCB to select the appropriate
number of punch holes.
•Each press on SW1002 moves the selection through the following
(repeatedly from top to bottom).
Number of punch holes
2 holes (Puncher Unit-J1)
2/3 holes (Puncher Unit-K1)
4 holes (Puncher Unit-G1)
4 holes (Puncher Unit-H1)
3) Press SW1003 on the punch controller PCB twice. The presses will
store the selected number of punch holes on the punch controller
PCB.
•A single press on SW1003 will cause the LED indication to flash;
another press on SW1003 will cause the indication to remain ON to
indicate the end of registration.
4) Shift all bits of DIPSW1001 to OFF.
D. After Replacing the EEP-ROM (IC1002)
1) Turn off the host machine.
2) Set bits 1 through 4 on the punch controller PCB as follows:
ON
1
Fig.F05-102-03
3) Press SW1002 and SW1003 on the punch controller PCB at the
same time.
•The presses will initialize the EEP-ROM. At the end, all LEDs
(LED1001, LED1002, LED1003) will go ON.
4) Adjust the sensor output, and store the number of punch holes.
E. Setup by the diag simulation of the printer
(1) When installed to the printer model
1) Select "CONSOLE FIN. SET X" in the diag mode.
CONSOL FIN. SET X
Fig.F05-102-04
2) Select the setup value to be changed with [
2
3
4
LED1001
LED1002
LED1003
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
2
3
4
] [
] keys.
AR-FN7/PN1 ADJUSTMENTS 8-2
The adjustable setup values are shown in the table below.
X:
Adjustment content
A Saddle binding position
adjustment
B Saddle folding position
adjustment
C Front alignment position
adjustment
D Rear alignment position
adjustment
E Staple front one-position
binding position adjustment
F Staple rear one-position
binding position adjustment
G Staple 2-position binding
center adjustment
H Staple 2-position binding pitch
I Punch center position
adjustment (FR direction)
J Punch hole position
adjustment
(2)When installed to the multi-function model
1) Select "CONSOLE FINISHER SETTING" in SIM 3-10.
SIMULATION 3-10
CONSOLE FINISHER SETTING.
1. SADDLE POSITION
2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST
5. STAPLE REAR
6. STAPLE FRONT
7. STAPLE BOTH
8. STAPLE PITCH
9. PUNCH CENTER
10. PUNCH HOLE
Pressing START key
starts the operation.
SIMULATION 3-10
Stops at the end of the operation.
CONSOLE FINSHER SETTING
1.FOLDING POSITION
Fig.F05-102-05
2) Select a setup item and change the setup value.
Adjustment content
1 Saddle binding position
adjustment
2 Saddle folding position
adjustment
3 Front alignment position
adjustment
4 Rear alignment position
adjustment
5 Staple front one-position
binding position adjustment
6 Staple rear one-position
binding position adjustment
7 Staple 2-position binding
center adjustment
8 Staple 2-position binding pitch
adjustment
9 Punch center position
adjustment (FR direction)
10 Punch hole position
adjustment
(paper feed direction)
Default
Setup
Change/Setup
value
range
value 1
0 - 400
0.0707mm
0 - 400
0.0525mm
0 - 20
0.367mm
0 - 20
0.367mm
0 - 200
0.04374mm
0 - 200
0.04374mm
0 - 200
0.04374mm
0 - 99
0.04374mm
0 - 99
0 - 99
0.105mm
SELECT 1-10, AND PRESS START.
1
Pressing CUSTOM SETTING key
stops the operation.
720
Default
Setup
Change/Setup
value
range
value 1
0 - 400
0.0707mm
0 - 400
0.0525mm
0 - 20
0.367mm
0 - 20
0.367mm
0 - 200
0.04374mm
0 - 200
0.04374mm
0 - 200
0.04374mm
0 - 99
0.04374mm
0 - 99
0 - 99
0.105mm
Advertisement
Table of Contents
Troubleshooting
