Cisco CRS Configuration Manual page 418
Ios xr mpls configuration guide
Hide thumbs
Also See for CRS:
- User manual (304 pages) ,
- Configuration manual (292 pages) ,
- Command reference manual (155 pages)
Table of Contents
Advertisement
Configure the Ping and Traceroute: Example
Success rate is 100 percent (3 received replies/3 expected replies),
round-trip min/avg/max = 154/232/302 ms
This example shows an extract of the ping command with the jitter option.
RP/0/RP0/CPU0:router# ping mpls traffic-eng tunnel-mte 10 jitter 300
Sending 1, 100-byte MPLS Echos to tunnel-mte10,
timeout is 2.3 seconds, send interval is 0 msec, jitter value is 300 msec:
Codes: '!' - success, 'Q' - request not sent, '.' - timeout,
'L' - labeled output interface, 'B' - unlabeled output interface,
'D' - DS Map mismatch, 'F' - no FEC mapping, 'f' - FEC mismatch,
'M' - malformed request, 'm' - unsupported tlvs, 'N' - no rx label,
'P' - no rx intf label prot, 'p' - premature termination of LSP,
'R' - transit router, 'I' - unknown upstream index,
'X' - unknown return code, 'x' - return code 0, 'd' - DDMAP
Type escape sequence to abort.
Request #1
! reply addr 192.168.222.2
! reply addr 192.168.140.2
! reply addr 192.168.170.1
Success rate is 100 percent (3 received replies/3 expected replies),
round-trip min/avg/max = 148/191/256 ms
This example shows an extract of the ping command with the ddmap option.
RP/0/RP0/CPU0:router# ping mpls traffic-eng tunnel-mte 10 ddmap
Sending 1, 100-byte MPLS Echos to tunnel-mte10,
timeout is 2.2 seconds, send interval is 0 msec, jitter value is 200 msec:
Codes: '!' - success, 'Q' - request not sent, '.' - timeout,
'L' - labeled output interface, 'B' - unlabeled output interface,
'D' - DS Map mismatch, 'F' - no FEC mapping, 'f' - FEC mismatch,
'M' - malformed request, 'm' - unsupported tlvs, 'N' - no rx label,
'P' - no rx intf label prot, 'p' - premature termination of LSP,
'R' - transit router, 'I' - unknown upstream index,
'X' - unknown return code, 'x' - return code 0, 'd' - DDMAP
Type escape sequence to abort.
Request #1
! reply addr 192.168.222.2
! reply addr 192.168.140.2
! reply addr 192.168.170.1
Success rate is 100 percent (3 received replies/3 expected replies),
round-trip min/avg/max = 105/178/237 ms
RP/0/RP0/CPU0:router# show mpls traffic-eng tunnels p2mp 10
Mon Apr 12 12:13:55.075 EST
Signalling Summary:
Name: tunnel-mte10
Status:
Admin: up
Config Parameters:
Cisco IOS XR MPLS Configuration Guide for the Cisco CRS Router, Release 5.1.x
400
LSP Tunnels Process:
RSVP Process:
Forwarding:
Periodic reoptimization:
Periodic FRR Promotion:
Auto-bw enabled tunnels:
Oper: up (Up for 12w4d)
running
running
enabled
every 3600 seconds, next in 654 seconds
every 300 seconds, next in 70 seconds
0 (disabled)
Implementing MPLS OAM
Advertisement
Table of Contents
