Numbered Acls; Extended Acls - Cisco 3845 - Security Bundle Router Software Manual
Software configuration guide
Hide thumbs
Also See for 3845 - Security Bundle Router:
- Manual (94 pages) ,
- Quick start manual (38 pages) ,
- Hardware installation manual (418 pages)
Table of Contents
Advertisement
Chapter 26
Configuring Network Security with ACLs
This example uses a standard ACL to filter traffic coming into Server B from a port, permitting traffic
only from Accounting's source addresses 172.20.128.64 to 172.20.128.95. The ACL is applied to traffic
coming out of routed Port 1 from the specified source address.
Switch(config)# access-list 6 permit 172.20.128.64 0.0.0.31
Switch(config)# end
Switch# show access-lists
Standard IP access list 6
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# ip access-group 6 out
This example uses an extended ACL to filter traffic coming from Server B into a port, permitting traffic
from any source address (in this case Server B) to only the Accounting destination addresses
172.20.128.64 to 172.20.128.95. The ACL is applied to traffic going into routed Port 1, permitting it to
go only to the specified destination addresses. Note that with extended ACLs, you must enter the
protocol (IP) before the source and destination information.
Switch(config)# access-list 106 permit ip any 172.20.128.64 0.0.0.31
Switch(config)# end
Switch# show access-lists
Extended IP access list 106
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# ip access-group 106 in
Numbered ACLs
In this example, network 36.0.0.0 is a Class A network whose second octet specifies a subnet; that is, its
subnet mask is 255.255.0.0. The third and fourth octets of a network 36.0.0.0 address specify a particular
host. Using access list 2, the switch accepts one address on subnet 48 and reject all others on that subnet.
The last line of the list shows that the switch accepts addresses on all other network 36.0.0.0 subnets.
The ACL is applied to packets entering a port.
Switch(config)# access-list 2 permit 36.48.0.3
Switch(config)# access-list 2 deny 36.48.0.0 0.0.255.255
Switch(config)# access-list 2 permit 36.0.0.0 0.255.255.255
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# ip access-group 2 in
Extended ACLs
In this example, the first line permits any incoming TCP connections with destination ports greater than
1023. The second line permits incoming TCP connections to the Simple Mail Transfer Protocol (SMTP)
port of host 128.88.1.2. The third line permits incoming ICMP messages for error feedback.
Switch(config)# access-list 102 permit tcp any 128.88.0.0 0.0.255.255 gt 1023
Switch(config)# access-list 102 permit tcp any host 128.88.1.2 eq 25
Switch(config)# access-list 102 permit icmp any any
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# ip access-group 102 in
For another example of using an extended ACL, suppose that you have a network connected to the
Internet, and you want any host on the network to be able to form TCP connections to any host on the
Internet. However, you do not want IP hosts to be able to form TCP connections to hosts on your
network, except to the mail (SMTP) port of a dedicated mail host.
OL-23400-01
10 permit 172.20.128.64, wildcard bits 0.0.0.31
10 permit ip any 172.20.128.64 0.0.0.31
Cisco ME 3800X and 3600X Switch Software Configuration Guide
Configuring IPv4 ACLs
26-23
- Quick Links:
- Performance Features
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
