Table of Contents
Advertisement
Chapter 6
Maintenance
Copying a Bootable Image onto a Flash Memory Card
After you have formatted a new flash memory card, you can copy a bootable image onto it. To copy an
image, use the following procedure, which assumes the following:
•
•
•
To copy a bootable file (called new.image in the following examples) onto the flash memory card:
Boot the Cisco uBR7100 series router and allow it to initialize.
Step 1
Insert an unformatted flash memory card and format it using the procedure in the
Step 2
Memory Card" section on page
Note
Copy the new image (new.image) to the flash memory card and make this image the default boot image.
Step 3
Then reboot the router using the following series of commands:
Router> enable
Password: <password>
Router# copy tftp:new.image disk0:new.image
20575008 bytes available on device disk0, proceed? [confirm]
address or name of remote host [1.1.1.1]?
loading new.image from 1.1.1.1 (via Ethernet1/0):!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 7799951/15599616 bytes]
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCC
Router#
Router# configure terminal
Router(config)# no boot system
OL-5916-01
You have an I/O controller with a good image in the onboard flash memory single in-line memory
module (SIMM) so you can start the router.
The bootable image you want to copy to the flash memory card exists on a Trivial File Transfer
Protocol (TFTP) server to which you have access (meaning you know its name and have
connectivity to it), and at least one interface is available over which you can access this server.
To ensure access to a TFTP server, you must configure at least one network interface on your
Note
router. For instructions on using this procedure, refer to the Cisco uBR7100 Series Software
Universal Broadband Router Configuration Guide. See the
section on page -8
You know the filename of the image you want to copy onto the flash memory card.
If you have already formatted a flash memory card, you can use it to copy files. However, you
cannot boot from a flash memory card that was formatted on another type of system. To use the
card as a boot source, you must first reformat it on the router. To avoid potential problems when
inserting flash memory cards in your router, we recommend reformatting all your flash memory
cards during your regularly scheduled service times. The
section on page 6-8
contains instructions that explain how to reformat a flash memory card.
Cisco uBR7100 Series and Cisco uBR7100E Series Universal Broadband Router Hardware Installation Guide
6-8. Then proceed to Step 3.
Flash Memory Card Usage
"Related Documentation"
"Formatting a Flash
"Formatting a Flash Memory Card"
6-9
Advertisement
Table of Contents
Troubleshooting
