Table of Contents
Advertisement
The System Setup menu
Set the bass peak level gradually, then press ENTER at
the point just before the tone starts to distort.
display on the receiver shows RESUME while the volume
returns to its original position, then you automatically
return to the main Bass Peak Level menu.
4
When you're finished, press RETURN .
You will return to the Manual SP Setup menu.
X-Curve
Most soundtracks mixed for cinema sound too bright
when played back in large rooms. The X-Curve setting
acts as a kind of re-equalization for home theater
listening, and restores proper tonal balance of movie
2
soundtracks.
1
Select 'X-Curve' from the Manual SP Setup menu.
5.Manual SP Setup
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
:Return
2
Choose the X-Curve setting you want.
Use
to adjust the setting. The X-Curve is expressed
as a downwards slope in decibels per octave, starting at
2kHz. The sound becomes less bright as the slope
increases (to a maximum of -3.0dB/oct). Use the
following guidelines to set the X-Curve according to your
room size:
2
≤ ≤ ≤ ≤ 36
≤ ≤ ≤ ≤ 48
Room size (m
)
X-Curve (dB/oct) –0.5
–1
• If you select OFF, the frequency curve will be flat and
the X-Curve has no effect.
3
Select 'Return' then press ENTER to finish.
Note
1 If the YES or PLUS setting on the subwoofer is selected (in Speaker Setting on page 42), the test tone will only play back from the subwoofer. If not, the
test tone will play back from the front and surround speakers set to LARGE.
2 Since the principal is the same, X-Curve isn't applied when you're using any of the Home THX modes (see Using the Home THX modes on page 27).
3 If you don't have surround back speakers, or just have one, you won't be able to select this setting (Cannot select shows in the display).
1
The
5e.X-Curve
X-Curve
-2.0dB/oct
:Finish
≤ ≤ ≤ ≤ 60
≤ ≤ ≤ ≤ 72
≤ ≤ ≤ ≤ 300 ≤ ≤ ≤ ≤ 1000
–1.5
–2
–2.5
–3
THX Audio Setting
For the most effective results when using the THX Select2
Cinema and THX MusicMode listening modes (see Using
the Home THX modes on page 27) with the Advanced
Speaker Array (ASA) system (see About THX on page 81),
it is required that you make the setting. See Placing the
speakers on page 18 for more on THX speaker
3
placement.
1
Select 'THX Audio Setting' from the Manual SP
Setup menu.
5.Manual SP Setup
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
2
Specify the distance of your surround back speakers
from each other.
5f.THX Audio Setting
SB SP Position
0.0-0.3m
SBL-SBR
• 0.0 – 0.3m – Surround speakers within 30cm apart
(best for THX surround sound).
• > 0.3 – 1.2m – Surround speakers between 30cm and
1.2m apart.
• 1.2m < – Surround speakers more than 1.2m apart.
3
When you're finished, press RETURN.
You will return to the Manual SP Setup menu.
:Return
:Finish
07
45
En
- Quick Links:
- Connecting Using Hdmi
- Specifications
Hide quick links:
Advertisement
Table of Contents
