Cisco TelePresence SX20 Codec Reference Manual page 77
Application programming interface (api)
Hide thumbs
Also See for TelePresence SX20 Codec:
- Reference manual (206 pages) ,
- Administrator's manual (177 pages) ,
- User manual (88 pages)
Table of Contents
Advertisement
Cisco TelePresence SX20 Codec
Contents
Introduction
xConfiguration Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self-view) on after a call. The
value reflects the monitor roles set for the different outputs in the Video Output HDMI MonitorRole
settings.
The setting applies both when self-view is displayed in full screen, and when it is displayed as
picture-in-picture (PiP), but only if the Video Monitors setting is set to Dual.
Requires user role: ADMIN
Value space: <First/Second/Current>
First: The self-view picture will be shown on outputs with the Video Output HDMI MonitorRole set
to First.
Second: The self-view picture will be shown on outputs with the Video Output HDMI MonitorRole
set to Second.
Current: When leaving a call, the self-view picture will be kept on the same output as it was during
the call.
Example: xConfiguration Video SelfviewDefault OnMonitorRole: Current
xConfiguration Video Monitors
A role is assigned to each monitor using the Video Output HDMI [n] MonitorRole setting. The monitor
role decides which layout (call participants and presentation) will appear on the monitor that is
connected to this output. Monitors with different monitor roles will have different layouts. Both
monitors cannot have monitor role First.
The monitor layout mode that is set in the Video Monitors setting should reflect the number of
different layouts you want in your room setup. Note that some monitors can be reserved for
presentations.
Requires user role: ADMIN
Value space: <Auto/Single/Dual/DualPresentationOnly>
Auto: The number of monitors connected to the codec is automatically detected, and the layout is
distributed on the monitors according to the MonitorRole settings.
Single: The layout is shown on one monitor. If two monitors are connected to the codec, one of
them will be disabled.
Dual: The layout is distributed on monitors with monitor role First and Second. If a presentation is
part of the layout, all participants in the call are shown on the monitor with monitor role First, and
the presentation is shown on the monitor with monitor role Second.
DualPresentationOnly: All participants in the call are shown on the monitor with monitor role First.
If a presentation is part of the layout, the presentation is shown on the monitor with monitor role
Second.
Example: xConfiguration Video Monitors: Auto
SX20 Codec API Reference Guide TC7.3, OCTOBER 2015.
D14949.13
About the API
xConfiguration
xConfiguration
xConfiguration Video OSD Mode
xConfiguration Video OSD WallpaperSelection
xConfiguration Video OSD LanguageSelection
77
xCommand
The OSD (On Screen Display) is where you find the menus, dialogs, icons and indicators, and the
navigation is done with a remote control. Define which icons and information to be displayed on
screen.
Requires user role: ADMIN
Value space: <Off/On>
Off: Hide the on-screen menus, icons and indicators.
On: Display the on-screen menus, icons and indicators.
Example: xConfiguration Video OSD Mode: On
In cases where you want to prevent users from easily changing the wallpaper setting from the
Settings menu, the wallpaper setting can be made available from within the Administrator Settings
menu. The administrator settings can be password protected. The OSD (On Screen Display) is
where you find the menus, dialogs, icons and indicators, and the navigation is done with a remote
control.
Requires user role: ADMIN
Value space: <Off/On>
Off: The wallpaper setting will be available from within the Video settings in the Administrator
Settings.
On: The Wallpaper menu will be available from the Settings menu.
Example: xConfiguration Video OSD WallpaperSelection: On
In cases where you want to prevent users from easily changing the language settings from the
Settings menu, the language settings can be made available from within the Administrator Settings
menu. The administrator settings can be password protected. The OSD (On Screen Display) is
where you find the menus, dialogs, icons and indicators, and the navigation is done with a remote
control.
Requires user role: ADMIN
Value space: <Off/On>
Off: The language settings will be available from within the SystemUnit settings in the
Administrator Settings.
On: The Language menu will be available from the Settings menu.
Example: xConfiguration Video OSD LanguageSelection: On
API Reference Guide
xStatus
Appendices
Copyright © 2015 Cisco Systems, Inc. All rights reserved.
- Quick Links:
- Table of Contents
- Commands
- Configurations
Hide quick links:
Advertisement
Chapters
Table of Contents
