Cisco TelePresence SX20 Codec Reference Manual page 38
Application programming interface (api)
Hide thumbs
Also See for TelePresence SX20 Codec:
- Reference manual (206 pages) ,
- Administrator's manual (177 pages) ,
- User manual (88 pages)
Table of Contents
Advertisement
Cisco TelePresence SX20 Codec
Contents
Introduction
xConfiguration Conference [1..1] FarEndControl SignalCapability
Set the far end control (H.224) signal capability mode.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the far end control signal capability.
On: Enable the far end control signal capability.
Example: xConfiguration Conference 1 FarEndControl SignalCapability: On
xConfiguration Conference [1..1] Encryption Mode
Define the conference encryption mode. A padlock with the text "Encryption On" or "Encryption
Off" displays on screen for a few seconds when the conference starts.
NOTE: If the TC-NC software (no crypto) is installed on the video system, the encryption mode is
always Off.
Requires user role: ADMIN
Value space: <Off/On/BestEffort>
Off: The system will not use encryption.
On: The system will only allow calls that are encrypted.
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will be
encrypted. If not, the call will proceed without encryption.
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support
encryption. If not, the conference will be unencrypted.
Example: xConfiguration Conference 1 Encryption Mode: BestEffort
xConfiguration Conference [1..1] DefaultCall Protocol
Set the Default Call Protocol to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <Auto/H323/Sip/H320>
Auto: Enables auto-selection of the call protocol based on which protocols are available. If multiple
protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the system cannot
register, or the call protocol is not enabled, the auto-selection chooses H323.
H323: All calls are set up as H.323 calls.
Sip: All calls are set up as SIP calls.
H320: All calls are set up as H.320 calls (only applicable if connected to a Cisco TelePresence
ISDN Link gateway).
Example: xConfiguration Conference 1 DefaultCall Protocol: Auto
SX20 Codec API Reference Guide TC7.3, OCTOBER 2015.
D14949.13
About the API
xConfiguration
xConfiguration
xConfiguration Conference [1..1] DefaultCall Rate
xConfiguration Conference [1..1] MaxTransmitCallRate
xConfiguration Conference [1..1] MaxReceiveCallRate
38
xCommand
Set the Default Call Rate to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: xConfiguration Conference 1 DefaultCall Rate: 1920
Specify the maximum transmit bit rate to be used when placing or receiving calls. Note that this is
the maximum bit rate for each individual call; use the Conference MaxTotalTransmitCallRate setting
to set the aggregated maximum for all simultaneous active calls.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: xConfiguration Conference 1 MaxTransmitCallRate: 6000
Specify the maximum receive bit rate to be used when placing or receiving calls. Note that this is
the maximum bit rate for each individual call; use the Conference MaxTotalReceiveCallRate setting
to set the aggregated maximum for all simultaneous active calls.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: xConfiguration Conference 1 MaxReceiveCallRate: 6000
API Reference Guide
xStatus
Appendices
Copyright © 2015 Cisco Systems, Inc. All rights reserved.
- Quick Links:
- Table of Contents
- Commands
- Configurations
Hide quick links:
Advertisement
Chapters
Table of Contents
