Verifying The Transceiver Modules - Cisco ASR 9000 Series Installation Manual
Aggregation services router
ethernet line card
Hide thumbs
Also See for ASR 9000 Series:
- Command reference manual (1138 pages) ,
- Routing configuration manual (702 pages) ,
- Reference manual (696 pages)
Table of Contents
Advertisement
Configuring and Troubleshooting Line Card Interfaces
Add any other configuration subcommands required to enable routing protocols and adjust the interface
Step 8
characteristics. Examples of such subcommands are:
RP/0/RSP0/CPU0:router(config-if)# flow-control ingress
RP/0/RSP0/CPU0:router(config-if)# mtu 1448
RP/0/RSP0/CPU0:router(config-if)# mac-address 0001.2468.ABCD
Step 9
When you have included all the configuration subcommands to complete the configuration, enter the
commit command to commit all changes you made to the running configuration.
RP/0/RSP0/CPU0:router(config-if)# commit
Enter Ctrl-Z to exit configuration mode. If you did not enter the commit command, you will be
Step 10
prompted to do so:
RP/0/RSP0/CPU0:router(config-if)#
Uncommitted changes found, commit them before exiting(yes/no/cancel)? [cancel]:
Answer yes to commit, no to exit without a commit, or cancel to cancel the exit (default).
Write the new configuration to memory:
Step 11
RP/0/RSP0/CPU0:router# copy run disk0:/config/running/alternate_cfg:/router.cfg
Destination file name (control-c to abort): [/router.cfg]?
The destination file already exists. Do you want to overwrite? [no]: yes
Building configuration.
223 lines built in 1 second
[OK]
The system displays an OK message when the configuration has been stored.
Verifying the Transceiver Modules
Use the show inventory all command to display SFP or XFP module information for all transceiver
modules currently installed in the router. To display SFP or XFP module information for a particular
module, you can use the show inventory location <slot ID> command.
The output of these commands lists such information as the slot ID, transceiver type, description,
product ID, version, and serial number.
For example, to list module information for all modules in the router:
RP/0/RSP0/CPU0:router# show inventory all
NAME: "module 0/RSP0/CPU0", DESCR: "ASR9K Fabric, Controller, 4G memory"
PID: A9K-RSP-4G
NAME: "module compact-Flash 0/RSP0/CPU0", DESCR: " CompactFlash"
PID: cFLASH
NAME: "module 0/1/CPU0", DESCR: "40-Port GE Line Card, Requires SFPs"
PID: A9K-40GE-B
NAME: "module mau 0/1/CPU0/2", DESCR: "1000BASE-SX SFP (DOM), MMF, 550/220m"
PID: SFP-GE-S
NAME: "module mau 0/1/CPU0/3", DESCR: "1000BASE-SX SFP (DOM), MMF, 550/220m"
PID: SFP-GE-S
NAME: "module mau 0/1/CPU0/7", DESCR: "1000BASE-SX SFP (DOM), MMF, 550/220m"
PID: SFP-GE-S
Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide
2-6
Chapter 2
, VID: V01, SN: P3B-2
, VID: N/A, SN: 000000000301
, VID: V01, SN: FOC123081J6
, VID: V01 , SN: FNS12210HLY
, VID: V01 , SN: FNS12210HMJ
, VID: V01 , SN: FNS12210HM4
Verifying and Troubleshooting the Line Card Installation
OL-17500-08
Advertisement
Table of Contents
Troubleshooting
