Brother KE-436C Instruction Manual page 16
Electronic lockstitch pattern tacker with stepping foot and programming function
Hide thumbs
Also See for KE-436C:
- Parts manual (73 pages) ,
- Specifications (8 pages) ,
- Instruction manual (228 pages)
Table of Contents
Advertisement
1. Gently tilt back the machine head.
Note:
After tilting back the machine head, do not push the face side or the pulley side from above.
2. Pass the cord bundle (1) from the machine head through the hole (2) in the work table.
3. Gently return the machine head to its original position.
4. Remove the six screws (3), and then open the control box cover (main P.C. board mounting plate (4)).
Note:
When opening the cover, hold it securely so that it does not fall down.
5. Loosen the two screws (5), and then open the cord presser plate (6) in the direction of the white arrow and pass the cord
bundle (1) through the opening.
6. Remove the screw (7), and then pass it through the terminal holes in the ground cord (8) from the machine head. Then
re-tighten the screw (7) so that the ground cord (8) is secured as shown in the illustration.
7. Remove the screw (9), and then pass it through the terminal hole in the ground cord (10) from the upper shaft motor and
the ground cord (11) from the operation panel. Then re-tighten the screw (9) so that the ground cords (10) and (11) are
secured as shown in the illustration.
Note:
Make sure that the ground connections are secure in order to ensure safety.
8. Securely connect connectors P1 to P7, P11, P14, P18 and P20 as indicated in the table below.
Note:
Check that the connector is facing the correct way, and then insert it firmly until it locks into place.
Furthermore, lock the cord clamp at the top.
Machine head connectors
Connection location
Head position switch
X, Y, Sewing sensor
Synchronizer
Machine specification
select connector
Thread wiper solenoid
Thread take-up solenoid
Presser solenoid
Thread trimmer solenoid
Pulse motor, Y
Pulse motor, X
Operation panel
Upper shaft motor
EMERGENCY STOP switch
Solenoid valve
9. Secure the cord bundle (1) with the cord clamps (12) and (13).
10. Close the cord presser plate (6) in the direction of the black arrow, and secure it by tightening the screws (5).
Note:
Check that the cords do not get pulled when the machine head is tilted back gently.
11. Tighten the cover (main P.C. board mounting plate (4)) with the six screws (3).
Note:
Check that the cords do not come into contact with the fan (14) and that they are not clamped by the cover at this time.
No. of pins
Cord mark
9-pin
[1A]
12-pin
[1]
5-pin
[2]
8-pin
[3]
5-pin
[4]
4-pin
[5]
4-pin (blue)
[6]
4-pin
[7]
10-pin
[M]
3-pin
None
6-pin
[18]
12-pin
None
KE-436C
Connection location
on circuit board
P1-A (ORG1)
P1-B (ORG2)
P2 (SYNCHRO)
P3 (SELECT)
P4 (SOL2)
P5 (SOL)
P6 (YPM)
P7 (XPM)
P20 (RSPORT)
P11 (UVW)
P18 (HEAD)
P14 (AIR)
3. INSTALLATION
Cord clamps used
None
None
(G)
None
(G)(H)
(G)(H)
(G)(H)
(G)(H)
(A)(B)
(A)(B)(C)(D)(E)(F)
None
(A)(B)(C)(D)
10
Hide quick links:
Advertisement
Table of Contents
