Table of Contents
Advertisement
Software and Hardware Requirements
Software and Hardware Requirements
Table 2-1 lists the minimum Cisco IOS software release required to use the PA-T3 and the
PA-2T3 serial port adapters in supported router platforms.
Table 2-1
PA-T3 Port Adapter Software Requirements
Platforms
Cisco 7000 and Cisco 7500 series
• With VIP2-15(=) or VIP2-40(=)
• With VIP2-50(=)
Cisco 7200 series
• Cisco 7204VXR and Cisco 7206VXR
• Cisco 7204 and Cisco 7206
• Cisco 7202
Cisco uBR7200 series
• Cisco uBR7246 and Cisco uBR7223
Cisco 7100 Series
• Cisco 7120 series and Cisco 7140 series
Catalyst 5000 series switches
• With Catalyst RSM/VIP2-15(=) or
Catalyst RSM/VIP2-40(=)
Caution
installed. The VIP2 does not operate properly with the Route Processor (RP), Switch Processor (SP), or
Silicon Switch Processor (SSP) installed in the host Cisco series router.
The PA-T3 serial port adapter is considered a high-bandwidth port adapter; therefore, and at a
minimum, Cisco recommends that the PA-T3 serial port adapter be installed on the VIP2-15 or
Catalyst RSM/VIP2 motherboard (with 1 MB of SRAM and 8 MB of DRAM). Installation of the
PA-T3 serial port adapter on the VIP2-10 (with 512 KB of SRAM and 8 MB of DRAM) is not
recommended.
2-2
PA-T3 Serial Port Adapter Installation and Configuration
Recommended Minimum Cisco IOS Release
PA-T3
Cisco IOS Release 11.1(13)CA or a later
release of Cisco IOS Release 11.1 CA
Cisco IOS Release 11.1(14)CA or a later
release of Cisco IOS Release 11.1 CA
Cisco IOS Release 12.0(2)XE2 or a later
release of Cisco IOS Release 12.0 XE
Cisco IOS Release 12.0(3)T or a later release
of Cisco IOS Release 12.0 T
Cisco IOS Release 11.1(16)CA or a later
release of Cisco IOS Release 11.1 CA
Cisco IOS Release 11.1(19)CC1 or a later
release of Cisco IOS Release 11.1 CC
Cisco IOS Release 11.3(4)AA or a later
release of Cisco IOS Release 11.3 AA
Cisco IOS Release 12.0(2)XA or a later
release of Cisco IOS Release 12.0 XA
Cisco IOS Release 12.0(4)XE or a later
release of Cisco IOS Release 12.0 XE
Cisco IOS Release 12.0(5)T or a later release
of Cisco IOS Release 12.0 T
Cisco IOS Release 12.0(4)T or a later release
of Cisco IOS Release 12.0T
The VIP2 requires that the host Cisco 7000 series router have the RSP7000 and RSP7000CI
PA-2T3
Cisco IOS Release 11.1(16)CA or a later
release of Cisco IOS Release 11.1 CA
Cisco IOS Release 11.1(16)CA or a later
release of Cisco IOS Release 11.1 CA
Cisco IOS Release 12.0(2)XE2 or a later
release of Cisco IOS Release 12.0 XE
Cisco IOS Release 12.0(3)T or a later release
of Cisco IOS Release 12.0 T
Cisco IOS Release 11.1(16)CA or a later
release of Cisco IOS Release 11.1 CA
Cisco IOS Release 11.1(19)CC1 or a later
release of Cisco IOS Release 11.1 CC
Cisco IOS Release 11.3(4)AA or a later
release of Cisco IOS Release 11.3 AA
Cisco IOS Release 12.0(2)XA or a later
release of Cisco IOS Release 12.0 XA
Cisco IOS Release 12.0(4)T or a later release
of Cisco IOS Release 12.0T
Advertisement
Table of Contents
