Table of Contents
Advertisement
Quick Links
PA-4C-E 1-Port High-Performance
ESCON Channel Port Adapter Installation and
Configuration
Product Number: PA-4C-E(=)
Platforms Supported: Cisco 7200 Series Routers, including the Cisco 7200 VXR Routers
Document part number: OL-3473-02
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2007 Cisco Systems, Inc. All rights reserved.
Advertisement
Table of Contents
Related Manuals for Cisco PA-4C-E 1
Summary of Contents for Cisco PA-4C-E 1
- Page 1 Product Number: PA-4C-E(=) Platforms Supported: Cisco 7200 Series Routers, including the Cisco 7200 VXR Routers Document part number: OL-3473-02 Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA © 2007 Cisco Systems, Inc. All rights reserved.
-
Page 2: Document Revision History
This document contains the following four sections: Title Overview Preparing for Installation Removing and Installing Port Adapters Configuring the HP ESCON PA PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Date Change Summary April, 2007 Restructured to parallel other port adapter documentation. -
Page 3: Related Documentation
Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised technical documentation at: OL-3743-02 http://www-europe.cisco.com. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Preface... - Page 4 Preface http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02...
-
Page 5: Port Adapter Overview
HP ESCON PA. OL-3743-02 (Figure 1) provides a single channel attachment interface for connecting Cisco 7200 ESCON Channel Port Adapter, Faceplate View PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Overview HP ESCO N PA... - Page 6 For instructions on configuring Cisco IOS to use an HP ESCON PA image from the router Flash • memory card or SanDisk memory device, refer to the section on page PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration ETHERNET 10BT Cisco 7200 Series...
- Page 7 256 x 16 x 16 x 253 Up to 59 (through a 9032 ESCON Director) Up to 59 (through a 9032 ESCON Director); varies by control unit PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Overview “HP ESCON PA Microcode...
- Page 8 Figure 4 LED Boot Sequence * Because of the short duration of the LEDs, you will typically see only these LED sequences. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Loaded Signal Online (Figure...
-
Page 9: Port Adapter Slot Locations On The Supported Platforms
(Figure 5). ESCON cables are not available from Cisco. Refer to the ESCON ESCON Interface Duplex Connector for the ESCON Channel Port Adapter PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Overview Figure 6 shows the slot numbering on a... -
Page 10: Identifying Interface Addresses
The following subsections describe the interface address formats for the supported platforms: Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses, page 11 • PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Port Adapter Slots in the Cisco 7206 Router Blank port adapter... - Page 11 3 would have the address 3/0. If the HP ESCON PA was in port adapter slot 1, the interface address would be 1/0. OL-3743-02 Numbers Port adapter slot—1 on the number of slots in the router) Interface port—0 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Overview Syntax through 6 (depends...
-
Page 12: Preparing For Installation
By default, the HP ESCON PA microcode is loaded from the router Flash memory card or SanDisk memory device for the Cisco 7200 series routers. The default HP ESCON PA microcode version is found by entering the show microcode command. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02... -
Page 13: Hardware And Software Requirements
The HP ESCON PA requires that the Cisco 7200 series router is running Cisco IOS • Release 12.1(5)T or later. OL-3743-02 Microcode image names slot0:xcpa28-0 slot0:xcpa28-0 for basic configuration information. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Preparing for Installation “Upgrading Your HP ESCON PA... -
Page 14: Checking Hardware And Software Compatibility
Choose a product family or enter a specific product number to search for the minimum supported software release needed for your hardware. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Cisco IOS Release Image Names Image Names... -
Page 15: Safety Guidelines
à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS OL-3743-02 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Preparing for Installation... - Page 16 Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02...
- Page 17 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02...
-
Page 18: Electrical Equipment Guidelines
The HP ESCON PA contains laser LEDs. The expansion module is classified as a Class 1 laser product and is certified to conform to the requirements of EN60825-1:1994 and IEC825-1:1993. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02... -
Page 19: Laser Radiation
Laserstråling er til stede når enheten er åpen. Aviso Radiação laser presente quando aberto. ¡Advertencia! Radiación láser presente cuando el sistema está abierto. Varning! Laserstrålning pågår när enheten är öppen. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02... - Page 20 Non fissare il raggio con gli occhi. Advarsel Stirr ikke på strålen. Não olhe fixamente para o raio. Aviso ¡Advertencia! No mirar fijamente el haz. Varning! Laserstrålning när enheten är öppen. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02...
-
Page 21: Handling Port Adapters
Always use an ESD wrist strap when handling equipment. (See Figure 7 Metal carrier Printed circuit board OL-3743-02 Handling a Port Adapter PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Removing and Installing Port Adapters Figure... -
Page 22: Online Insertion And Removal
Before you begin installation, read the Note parts and tools required for installation. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration “Required Tools and Equipment” section on page 12 “Port Adapter for a list of OL-3743-02... -
Page 23: Port Adapter Removal And Installation
Hazardous voltage or energy is present on the backplane when the system is operating. Use caution Warning when servicing. Statement 1034 Caution When powering off the router, wait a minimum of 30 seconds before powering it on again. OL-3743-02 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Removing and Installing Port Adapters... - Page 24 Step 7 After the port adapter is properly seated, lock the port adapter lever. (See A.) PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Port adapter lever Cisco 7200 Series Note: This adapter Port adapter lever removal applies to any port or service adapter.
- Page 25 OL-3743-02 Connecting an ESCON Cable to an HP ESCON PA To an ESCON Director (switch) or host CPU PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Removing and Installing Port Adapters (Figure 8). Make certain the HP ESCO N PA...
-
Page 26: Using The Exec Command Interpreter
Enter the password (the password is case sensitive). For security purposes, the password is not displayed. When you enter the correct password, the system displays the privileged-level system prompt (#): Router# PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02... - Page 27 Step 1 configuration commands, as follows: Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# OL-3743-02 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA “Using the EXEC Command Interpreter” section...
-
Page 28: Checking The Configuration
Display all the current port adapters and their interfaces with the show controllers command. Verify that Step 2 the new HP ESCON PA appears in the correct slot. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration “Related Documentation” section on page “Checking the Configuration”... - Page 29 R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache 6 slot VXR midplane, Version 2.0 Last reset from power-on Bridging software. OL-3743-02 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA...
- Page 30 Rx Queues max_entries=221 poll_index=3 head=96 ring=4B0EB3E0 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Rev. 0 Compiled by jdoe on Thu 07-Sep-2000 12: Rev. 0 Compiled by jdoe on Thu 07-Sep-2000 12: Rev.
- Page 31 MTU 4472 bytes, BW 98304 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation CHANNEL, loopback not set ECA adapter card OL-3743-02 :1.0 :800-06347-02 :73-4454-02 :18902852000 :28-3405-02 :PA-4C-EB PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA...
-
Page 32: Using The Ping Command To Verify Network Connectivity
For complete descriptions of interface configuration commands and the configuration options available for each platform, refer to the publications listed in the PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration “Related Documentation” section on page “Related Documentation” section on page... - Page 33 Copy the HP ESCON PA microcode image to the Flash memory card in slot 0 or slot1, or to the SanDisk Step 3 memory device in disk 0 or disk 1. OL-3743-02 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA “Hardware and Software “Hardware and Software Requirements”...
- Page 34 .D unknown .D unknown .D unknown .D unknown .. unknown .. unknown .. unknown PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration CA94D289 20C18 2966 Sep 07 2000 09:07:07 ciscocert.pem 62000000 20C9C 1 Sep 18 2000 06:33:57 xcpa218-6...
- Page 35 73CB2859 74CE68 161196 Sep 18 2000 06:48:56 xcpa218-6_seg_tcpip 0989F473 7F31C8 680672 Sep 18 2000 06:49:04 xcpa218-6_seg_tn3270 36, then proceed to Step 3. PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA “Using the EXEC...
-
Page 36: Using Flash Memory
Expanding slot0:/xcpa218-6_seg_offload (91976 bytes):!!!!!!!!!!!!!!!!!! Expanding slot0:/xcpa218-6_seg_pca (68844 bytes):!!!!!!!!!!!!! Expanding slot0:/xcpa218-6_seg_push (15492 bytes):!!! Expanding slot0:/xcpa218-6_seg_sslc (827760 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Expanding slot0:/xcpa218-6_seg_tcpip (161196 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Expanding slot0:/xcpa218-6_seg_tn3270 (680672 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!! [OK - 4109312/8218624 bytes] PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02... - Page 37 May 19 2000 05:43:56 todays–config May 19 2000 09:54:53 fun1 May 19 2000 09:42:19 myfile1 May 19 2000 05:43:56 todays–config PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA command to view the deleted files. dir /deleted...
- Page 38 Loading xcpa26-1 from 1.1.1.22 (via FastEthernet0/0):! Expanding disk0:xcpa27-1_kernel_xcpa (406910 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_802 (245522 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_cmpc (564632 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_csna (96024 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_eca (460704 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_offload (91420 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_pca (68840 bytes):!!!!!!!!!!! PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02...
- Page 39 All diagnostic tests are run every time the adapter is started. They cannot be run independently. The external optical wrap test require special wrap plugs for the HP ESCON PA. Contact a service representative to obtain the appropriate wrap plugs OL-3743-02 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration Configuring the HP ESCON PA...
- Page 40 CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...