hit counter script
Cisco ASR1002 - ASR 1002 Router Quick Start Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. ASR1002 - ASR 1002 Router
  6. Quick start manual

Cisco ASR1002 - ASR 1002 Router Quick Start Manual

Quick start guide
Hide thumbs Also See for ASR1002 - ASR 1002 Router:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, Quick Start Manual
Q
S
G
UICK
TART
Cisco ASR 1002-F Router
1
Documentation and Resources
2
Obtaining Documentation and Submitting a Service Request
3
Cisco ASR 1002-F Router Overview
4
Prepare for Installation
5
Rack-Mount the Router
6
Connect the Router to the Network
7
Start the System
8
Configure the Router
9
After Installation
UIDE

Advertisement

Table of Contents
loading

Related Manuals for Cisco ASR1002 - ASR 1002 Router

Summary of Contents for Cisco ASR1002 - ASR 1002 Router

  • Page 1 UICK TART UIDE Cisco ASR 1002-F Router Documentation and Resources Obtaining Documentation and Submitting a Service Request Cisco ASR 1002-F Router Overview Prepare for Installation Rack-Mount the Router Connect the Router to the Network Start the System Configure the Router...

  • Page 2: Document Revision History

    Cisco ASR 1002-F Router Overview The Cisco ASR 1002-F (Fixed) Router is one of the Cisco ASR 1000 Series Aggregation Services Routers. It is the smallest router that supports all the general-purpose routing and security features of the Cisco ASR 1002 Routers. It uses the same internal control and data-plane architecture as the Cisco ASR 1002 Router.

  • Page 3: Prepare For Installation

    Caution The eUSB panel door on the side of the Cisco ASR 1002-F Router must not be opened. There is a Do Not Tamper label on the panel door. Do not remove the label. If there is a problem with the eUSB flash card, the chassis should be returned.

  • Page 4: Prepare For Rack-Mount Installation

    This section provides information for rack-mounting the router. Attach the Rack-Mount Brackets—Chassis Front-Mounted To install the rack-mount brackets on a Cisco ASR 1002-F Router for a front rack-mount configuration, follow these steps: Locate the threaded holes in the front sides of the chassis.

  • Page 5: Attach The Rack-Mount Brackets-Chassis Rear-Mounted

    Attach the Rack-Mount Brackets—Chassis Rear-Mounted To install the rack-mount bracket on a Cisco ASR 1002-F Router for a rear rack-mount configuration, follow these steps: Align the rack-mount bracket to the side of the router and locate the threaded ear holes in the rear sides of the chassis.
  • Page 6 Figure 4 Installing the Cisco ASR 1002-F Router in a Four-Post Rack - Front and Rear Rack-Mounting -POS SPA-4 XOC3 Rear rack equipment rail Front rack-mount bracket ear and holes Rear rack-mount bracket ear and holes Front rack equipment rail...

  • Page 7: Two-Post Rack Installation

    To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the rack-mount bracket ear holes specified in Step 5. Hold the chassis in position against the mounting rails and follow these steps: Step 5 a.
  • Page 8 Figure 5 shows the Cisco ASR 1002-F Router installed in a two-post rack Figure 5 Installing the Cisco ASR 1002-F Router in a Two-Post Rack SPA-4X OC3-P Rack equipment rail Rack-mount bracket ear and holes If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and Caution component damage.
  • Page 9 The cable-management brackets for the Cisco ASR 1002-F Router contain one independent cable-management “U” feature with two screws for each bracket. For the Cisco ASR 1000 Series SIP, these brackets work in tandem with SPA cable-management brackets to allow installation and removal of adjacent SPAs without the need to remove cables.

  • Page 10: Chassis Ground Connection Installation

    Before you connect power or turn on power to your router, you must provide an adequate chassis ground (earth) connection for the Cisco ASR 1002-F Router. The two-hole chassis ground lug and the respective screws that ship with your Cisco ASR 1002-F Router.

  • Page 11: Console And Auxiliary Port Cable Connections

    Console and Auxiliary Port Cable Connections The Cisco ASR 1002-F Router uses RJ-45 ports for both the console port to attach a console terminal or the auxiliary port to attach a modem. The console DCE-mode port connects a console terminal and a DTE-mode auxiliary port connects a modem...

  • Page 12: Management Ethernet Port Cable Connection

    (Asynchronous is the most common type of serial device; for example, most modems are asynchronous devices.) To meet Class A emissions requirements on the Cisco ASR 1002-F Router, shielded cables must be used for the console and auxiliary port connections.

  • Page 13: Connect The Shared Port Adapter Cables

    Connect the Shared Port Adapter Cables The instructions for connecting the cables for the shared port adapters installed in the Cisco ASR 1002-F Router are contained in the Cisco ASR 1000 Series Aggregation Services Routers SPA and SIP Hardware Installation Guide.

  • Page 14: Install The Cables Using The Cable-Management Bracket

    It might be necessary to bundle longer cables to avoid tangling them. Do this at the cable-management bracket or at Step 3 the rack, but leave enough slack in the cables to remove a Cisco ASR 1002-ESP-F and change cables as required. Also, do not block the power supply air vents with cables.

  • Page 15: Start The System

    Before you start the system, you must connect power to it. Connect AC Power to the Cisco ASR 1002-F Router This section provides instructions for installing the AC power supply into the Cisco ASR 1002-F Router. Read the safety warnings before you begin.
  • Page 16 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: AC power supplies 20 A and DC power supplies 30 A for Cisco ASR 1002-F Routers. Statement 1005 Figure 13 shows the AC power supply for the Cisco ASR 1002-F Router.
  • Page 17 No power to the power supply. Note To connect an AC power supply to the Cisco ASR 1002-F Router, follow the steps in the Installing the AC Power Supply, page Connect DC Power to the Cisco ASR 1002-F Router The DC power supply input connector is a euro-style terminal block.
  • Page 18 DC output voltages are within the normal operating range. To connect the DC power supply to a Cisco ASR 1002-F Router, follow these steps: Step 1 At the rear of the router, check that the power switch is in the Standby position on the power supply.
  • Page 19 Figure 15 Cisco ASR 1002-F Router DC Power Supply OU TP UT IN PU T FA N FA IL Th is un it m igh t ha ve on e po we m or e th an r su pp ly co Al l co nn ec nn ec tio n.
  • Page 20 Check the following conditions before you start the Cisco ASR 1002-F Router: • The Cisco ASR 1002-F Router has one slot for the Cisco ASR1002-SIP10-F. Make certain that the SPA is firmly seated in its subslot and its captive installation screws are securely tightened.
  • Page 21 During the boot process, observe the system LEDs. The PWR LED should be green. The STAT LED lights yellow to Step 3 indicate booting and then green when Cisco IOS is running. Figure 16 Integrated Cisco ASR1002-RP1 and Cisco ASR1002-ESP-F LEDs on Cisco ASR 1002-F Router ACTV STAT STBY...
  • Page 22 Port enabled and the Ethernet link is valid. **For more information about the small form-factor pluggable (SFP) transceiver modules that are compatible with Cisco ASR 1002 Built-in Gigabit Ethernet Ports (4x1GE), refer to the Modular Optics Compatibility section in the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide.

  • Page 23: Configure The Router

    Series Aggregation Services Routers Software Configuration Guide. Configure the Router Use this section for information on configuring the Cisco ASR 1002-F Router. Using the Console to Access the CLI To access the command-line interface using the console, follow these steps:...

  • Page 24: Configure Global Parameters Using The Set-Up Facility

    Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 --- System Configuration Dialog ---...
  • Page 25 GigabitEthernet0/0/2 unassigned unset down down GigabitEthernet0/0/3 unassigned unset down down GigabitEthernet0 unassigned YES unset administratively down down Configuring global parameters: Enter host name [Router]: The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.
  • Page 26 Proceed with reload? [confirm] *Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command. System Bootstrap, Version 12.2(20071105:235056) [gschnorr-mcp_rommon_rel_1_25 101], DEVELOPMENT SOFTWARE Copyright (c) 1994-2007 by cisco Systems, Inc. Compiled Mon 05-Nov-07 16:50 by gschnorr-mcp_rommon_rel_1_25 Current image running: Boot ROM1...

  • Page 27: Check The Running Configuration Settings

    Basic management setup configures enough connectivity for managing the system; extended setup will ask you to Note configure each interface on the system. For detailed information about setting global parameters, refer to the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide.

  • Page 28: Save The Running Configuration To Nvram

    Cisco ASR 1002 Router. Note For a complete list of Cisco ASR 1000 Series Routers field replaceable units, go to the Cisco ASR 1000 Series Aggregation Services Router Hardware Installation and Initial Configuration Guide, Chapter 9. The following topics are covered in this section: •...

  • Page 29: Replace The Shared Port Adapters

    Powering Off the Cisco ASR 1002-F Router Safely This section explains how to shut down the Cisco ASR 1002-F Router. It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reload operation is complete, then the Cisco ASR 1002-F Router can be powered off safely.

  • Page 30: Removing An Ac Power Supply

    Removing an AC Power Supply To remove a Cisco ASR 1002-F Router AC power supply that is not operating normally (and then replace the AC power supply within five minutes), follow this procedure: Slip on the ESD-preventative wrist strap that was included in the accessory kit.

  • Page 31: Installing The Ac Power Supply

    Replace the AC power supply within five minutes or the system will shutdown Step 5 You have removed an AC power supply from the Cisco ASR 1002-F Router and now must replace the AC power supply within five minutes. Installing the AC Power Supply Insert an AC power supply in power supply Slot 0 or power supply Slot 1 until it is full seated.
  • Page 32 18. Make sure the power cord is hanging loosely so that it cannot be disconnected from the AC power inlet. Figure 18 Cisco ASR 1002-F Router AC Power Cord - Left and Right OU TP UT INP UT FAI L...

  • Page 33: Removing The Dc Power Supply

    Removing the DC Power Supply Before you can remove a DC power supply from the Cisco ASR 1002-F Router, you must remove power from the power supply. Make certain that the chassis ground is connected before you begin removing and installing the power supply.

  • Page 34: Installing The Dc Power Supply

    Replace the DC power supply within five minutes or the system will shutdown. Step 7 You have completed the procedure for removing a DC power supply from the Cisco ASR 1002-F Router. Installing the DC Power Supply This section provides information about replacing a DC power supply in the Cisco ASR 1002-F Router.
  • Page 35 Turn the branch circuit breaker on at your site and the turn the Standby switch to the On (I) position. Step 8 Check that the power supply LEDs light when power is supplied to the router. Step 9 You have completed the procedure for installing a DC power supply in the Cisco ASR 1002-F Router.
  • Page 37 31 0 800 020 0791 Fax: 408 527-0883 Fax: 31 0 20 357 1100 Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices. © 2009 Cisco Systems, Inc. All rights reserved.

This manual is also suitable for:

Asr 1002-f

Table of Contents