Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yamaha YHT-33
Summary of Contents for Yamaha YHT-33
- Page 1 YHT-33 QUICK-CONNECT GUIDE...
-
Page 2: Tools And Parts
In addition to enhancing the sound of a video source, like your TV, DVD, or VCR, the YHT-33 also superbly reproduces audio sources, such as a CD player or a cassette deck. -
Page 3: Audio Components
YHT-33 Q Yamaha HTR-5240 Receiver (Rear Panel) NOTE: For your convenience, the Yamaha HTR-5240 receiver is equipped with two switched ac outlets (100 W max.). If desired, use them to power on connected components (e.g., CD player or turntable) each time the receiver is turned on. - Page 4 YHT-33 S ONNECTING NS-A16 SW-201 (Front Right Ch.) (Subwoofer) POWER STANDBY-RED ON-GREEN AUTO STANDBY HIGH INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS Clear/ Clear Stripe Wire To AC Outlet Wire Yamaha HTR-5240 A/V Receiver (Rear Panel Speaker Terminals) Clear/Stripe Clear...
- Page 5 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS ❶ To AC Outlet YHT-33 Q SW-201 S UBWOOFER 4. Play an audio source and adjust the HTR-5240’s VOLUME control to a desired listening level. 5. On the SW-201, increase the volume gradually to adjust the balance the volume between the SW-201 Subwoofer and the NS-A16 Main Speakers.
- Page 6 IDEO OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. VIDEO SIGNAL VIDEO SAT/D-TV MONITOR...
-
Page 7: Rear Panel
Dolby Digital is a trademark of Dolby Laboratories Licensing Corporation. DTS is a trademark of DTS Technology LLC. YHT-33 Q LAYER Yamaha HTR-5240 Receiver (Rear Panel) ❶ Remove dust cap NOTES: • On both ends of the optical-fiber cable, align and firmly insert each plug into its mating terminal. -
Page 8: Satellite Receiver
OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. AUDIO SIGNAL SAT/D-TV Use RCA Audio Cables And Jacks... - Page 9 ABLE ASIC NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. ANT In Basic Cable (From Wall Jack) Descrambler Premium Cable...
- Page 10 To Enter Setup Codes Use To Enter Setup Mode The YHT-33 Home Theater package includes a univer- sal remote control. It comes pre-programmed with factory codes to control your HTR-5240 receiver and most Yamaha audio components. To program other brands of components (i.e., TV, VCR, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer’s...
-
Page 11: Setting U P Your Vcr
5. To verify the code works, aim the remote control at the VCR, press VCR, and then press POWER. The VCR should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. YHT-33 Q EMOTE ONTROL ONTINUED ETTING THER 1. -
Page 12: Resetting Remote Control To Factory Codes
(on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. ©2000 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 YHT-33 Q...