Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yamaha YHT-24
Summary of Contents for Yamaha YHT-24
- Page 1 YHT-24 RAFT QUICK-CONNECT GUIDE...
-
Page 2: Tools And Parts
In addition to enhancing the sound of a video source, like your TV or VCR, the YHT-24 also superbly reproduces audio sources, such as a CD player or a cassette deck. This Quick-Connect Guide will help you get started. -
Page 3: Audio Components
WOOFER OUTPUT NOTE: For your convenience, the Yamaha HTR-5440 receiver is equipped with two switched ac outlets (100 W max.). If desired, use them to power on connected components (e.g.,CD player) each time the receiver is turned on. However, do not use them for components equipped with clocks (e.g.,VCR). - Page 4 YHT-24 S ONNECTING NS-AP280 SW-201 (Front Right Ch.) (Subwoofer) POWER VOLUME STANDBY-RED ON-GREEN AUTO STANDBY HIGH INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS Stripe Wire To AC Outlet DIGITAL INPUT COAXIAL OPTICAL Yamaha HTR-5440 D-TV/CBL A/V Receiver (Rear Panel) Stripe...
-
Page 5: Satellite Receiver
– WOOFER OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5440 receiver. VIDEO SIGNAL D-TV/CBL IN VCR 1 OUT MONITOR OUT... - Page 6 DIGITAL OUT AUDIO DIGITAL MPEG DTS OPTICAL COAXIAL VIDEO Yamaha DV-S 5350 DVD Player (Rear Panel) U I C K O N N E CT MAINS IMPEDANCE SELECTOR AC OUTLETS SWITCHED SET BEFORE POWER ON 100W MAX.
- Page 7 WOOFER OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5440 receiver. Use RCA Audio Cables And Jacks For Audio Interconnections. D-TV/CBL...
- Page 8 VCR 1 AUDIO SIGNAL NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5440 receiver. ANT In Basic Cable (From Wall Jack) Descrambler...
- Page 9 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS ❶ To AC Outlet YHT-24 Q SW-201 S UBWOOFER 4. Play an audio source and adjust the HTR-5440’s VOLUME control to a desired listening level. 5. On the SW-201, increase the volume gradually to adjust the balance the volume between the SW-201 Subwoofer and the NS-AP280 Main Speakers.
- Page 10 HTR-5440 receiver and most Yamaha audio components. To program other brands of compo- nents (i.e., TV, VCR, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer’s codes (listed on the back pages of the HTR-5440 Owner’s Manual).
-
Page 11: Setting U P Your Vcr
5. To verify the code works, aim the remote control at the VCR, press VCR, and then press POWER. The VCR should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. YHT-24 Q EMOTE ONTROL ONTINUED ETTING THER 1. -
Page 12: Resetting Remote Control To Factory Codes
(on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. ©2001 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 YHT-24 Q...