hit counter script
Yamaha YHT-34 Quick Connect Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Speaker System
  5. YHT-34
  6. Quick connect manual
Yamaha YHT-34 Quick Connect Manual

Yamaha YHT-34 Quick Connect Manual

Surround sound system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
YHT-34
1
D
ST
RAFT
QUICK-CONNECT GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Yamaha YHT-34

Summary of Contents for Yamaha YHT-34

  • Page 1 YHT-34 RAFT QUICK-CONNECT GUIDE...

  • Page 2: Tools And Parts

    In addition to enhancing the sound of a video source, like your TV, DVD, or VCR, the YHT-34 also superbly reproduces audio sources, such as a CD player or a cassette deck.

  • Page 3: Audio Components

    WOOFER OUTPUT NOTE: For your convenience, the Yamaha HTR-5450 receiver is equipped with two switched ac outlets (100 W max.). If desired, use them to power on connected components (e.g.,CD player) each time the receiver is turned on. However, do not use them for components equipped with clocks (e.g.,VCR).

  • Page 4: Initial Settings

    YHT-34 S ONNECTING NS-A328 (Front Right) Clear/ Clear Stripe Wire Wire STANDBY/ON HIGH CUT VOLUME 50 Hz 150 Hz Initial Settings (on Front Panel – also see page 9) Yamaha HTR-5450 A/V Receiver (Rear Panel Speaker Terminals) Clear/ Clear Stripe...

  • Page 5: Satellite Receiver

    – WOOFER OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5450 receiver. VIDEO SIGNAL D-TV/CBL IN VCR 1 OUT MONITOR OUT...
  • Page 6 • Keep dust caps and reattach them if terminals are not used. NOTE: Use the optical connection to enjoy 5.1-channel surround sound found on DVDs recorded in the Dolby Digital or DTS Digital Surround format. Yamaha DV-C6280 DVD Player (Rear Panel) U I C K O N N E CT...
  • Page 7 WOOFER OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5450 receiver. Use RCA Audio Cables And Jacks For Audio Interconnections. D-TV/CBL...
  • Page 8 DIGITAL AUDIO SIGNAL OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5450 receiver. ANT In Basic Cable (From Wall Jack) Descrambler...

  • Page 9: Initial Adjustment

    OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 1 POWER ❷ YHT-34 Q YST-SW45 S UBWOOFER 4. Play an audio source and adjust the HTR-5450’s VOLUME control to a desired listening level. 5. On the YST-SW45’s front panel, increase the VOLUME control gradually to adjust the balance the volume between the YST-SW45 Subwoofer and the NS-A328 Main Speakers.
  • Page 10 To Enter Setup Codes Use To Enter Setup Mode The YHT-34 Home Theater package includes a univer- sal remote control. It comes pre-programmed with factory codes to control your HTR-5450 receiver and most Yamaha audio components. To program other brands of components (i.e., TV, VCR, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer’s...
  • Page 11 5. To verify the code works, aim the remote control at the VCR, press VCR, and then press POWER. The VCR should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. YHT-34 Q EMOTE ONTROL ONTINUED ETTING THER 1.

  • Page 12: Resetting Remote Control To Factory Codes

    (on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. ©2001 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 YHT-34 Q...

Table of Contents