Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yamaha YHT-18
Summary of Contents for Yamaha YHT-18
- Page 1 TV and video source YHT-18 RAFT QUICK-CONNECT GUIDE...
-
Page 2: Tools And Parts
In addition to enhancing the sound of a video source, like your TV, DVD, or VCR, the YHT-18 also superbly reproduces audio sources, such as a CD player or a cassette deck. -
Page 3: Audio Components
WOOFER OUTPUT NOTE: For your convenience, the Yamaha HTR-5440 receiver is equipped with two switched ac outlets (100 W max.). If desired, use them to power on connected components (e.g.,CD player) each time the receiver is turned on. However, do not use them for components equipped with clocks (e.g.,VCR). - Page 4 YHT-18 S ONNECTING NX-220P SW-P201 (Front Right Ch.) (Subwoofer) POWER VOLUME STANDBY-RED ON-GREEN AUTO STANDBY HIGH INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS Stripe Wire To AC Outlet DIGITAL INPUT COAXIAL OPTICAL Yamaha HTR-5440 D-TV/CBL A/V Receiver (Rear Panel) Stripe...
- Page 5 – WOOFER OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5440 receiver. VIDEO SIGNAL D-TV/CBL IN VCR 1 OUT MONITOR OUT...
-
Page 6: Dvd Player
DIGITAL INPUT CD, on the HTR-5440 receiver (see detail above). Then rename the digital input on the HTR-5440 to “DVD” (see the HTR-5440 Owner’s Manual for the procedure). YHT-18 Q Yamaha HTR-5440 Receiver (Rear Panel) SPEAKERS – –... - Page 7 – WOOFER OUTPUT NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5440 receiver. D-TV/CBL VCR 1 AUDIO SIGNAL Use RCA Audio Cables And Jacks For Audio Interconnections...
- Page 8 VCR 1 AUDIO SIGNAL NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5440 receiver. ANT In Basic Cable (From Wall Jack) Descrambler...
- Page 9 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS ❶ To AC Outlet YHT-18 Q SW-P201 S UBWOOFER 4. Play an audio source and adjust the HTR-5440’s VOLUME control to a desired listening level. 5. On the SW-P201, increase the volume gradually to adjust the balance the volume between the SW-P201 Subwoofer and the NX-220P Main Speakers.
- Page 10 To Enter Setup Codes Use To Enter Setup Mode The YHT-18 Home Theater package includes a univer- sal remote control. It comes pre-programmed with factory codes to control your HTR-5440 receiver and most Yamaha audio components. To program other brands of components (i.e., TV, VCR, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer’s...
- Page 11 5. To verify the code works, aim the remote control at the VCR, press VCR, and then press POWER. The VCR should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. YHT-18 Q EMOTE ONTROL ONTINUED ETTING 1.
-
Page 12: Playing Videocassette
(on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. ©2001 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (888) 435-7922...