Table of Contents
Advertisement
Useful Remote Control Features
13
Useful Remote Control Features
Learning function of the remote control
unit
You can operate the connected AV products (AV Receiver,
Cable Box, SAT tuner, VCR, DVD, DVD recorder, LD) using the
remote control's learning function. The remote control can
memorize other remote control's codes.
2 cm to 5 cm (0.8 inches to 2.0 inches)
Remote control
(Supplied accessory)
Using the learning function
1
Slide the Mode switch to match the type of device to be
learned.
2
Press EDIT/LEARN and 2 at the same time.
• The LED flashes.
3
Press a button to be learned.
• The LED lights up.
• For the functions that can be learned, see pages 99 to
102.
• When the device's remote is memorized, the LED
flashes.
4
Press EDIT/LEARN again to exit the Learn mode.
NOTE
• To exit the Learn mode before it is complete, press EDIT/
LEARN again.
• If the Mode switch selection is changed when EDIT/LEARN
and 2 are pressed (the LED is flashing), the Learn session is
canceled.
• If the Mode switch selection is changed when a button to be
learned is pressed after EDIT/LEARN and 2 have been
pressed (the LED lights up), the Learn session is not
canceled and the selected mode and button remain
effective.
• If no operation is performed for more than one minute after
having pressed EDIT/LEARN and 2 (the LED is flashing), the
Learn session is canceled.
• If a button to be learned is pressed after having pressed
EDIT/LEARN and 2 (the LED is lit), the Learn session is
canceled in 30 seconds and the LED restarts blinking again.
• Code transmission finishes in approximately two seconds.
Do not interrupt it halfway. Wait until the LED flashes again.
• When using any of the receiver buttons (a, INPUT, or
VOL +/–), the learned manufacturer code remains the same
regardless of the Mode switch position or even if the switch
is shifted to a different position.
92
En
Remote control of
AV product
Presetting manufacturer codes to
control other devices
Presetting manufacturer codes
1
Slide the Mode switch to match the type of device to be
preset.
2
Press EDIT/LEARN and 1 at the same time.
• The LED flashes.
3
Press 0 – 9 to enter the manufacturer code. See page 94.
• Preset mode is finished when the LED blinks Off.
Library Search
In the event that the device code for a particular target unit is
unknown, cycle through the available codes for that type of
device. Sample the functions from each code in order to find
the code that properly operates the target device.
1
Slide the Mode switch to match the type of device to be
preset.
2
Press EDIT/LEARN and 3 at the same time.
• The LED indicator flashes and the remote control unit
enters the Library Search programming mode.
3
Press either SOURCE POWER, PLAY, 1 or CH+ to sample
the selected code.
4
If the code is missing, press
code or return to the previous code and repeat step 3.
5
Press ENTER when the code that properly operates the
target device is found.
• All the available buttons for the selected mode are
programmed to the remote control. The remote control
unit returns to normal operation (LED lights for one
second to confirm addition).
Delete Learning
You can delete a learned code by either overwriting it with a
new code on the same button or performing the procedure
below.
1
Press EDIT/LEARN and 2 at the same time.
• The LED indicator flashes and the remote control unit
enters the Learning mode.
2
Press and hold TV a for more than two seconds.
• The remote control unit starts deleting all learned codes
in the selected mode (marked by a lit LED).
• When completed, the LED blinks Off and the remote
control unit returns to normal operation.
/
to advance to the next
- Quick Links:
- Remote Control Unit
- Troubleshooting
Hide quick links:
Advertisement
Chapters
Table of Contents
