Table of Contents
Advertisement
Installation and Removal of the TCC Cards
Step 2
Ensure that you have enough clearance to accommodate any interface equipment that you will connect
directly to the Supervisor Card ports.
Step 3
Loosen the captive installation screws that secure the TCC blank panel or the existing TCC card
(whichever is present).
Note
If a TCC card is currently installed in the chassis slot, disconnect the associated cabling before loosening
the captive screws to maintain proper grounding of the TCC card.
Step 4
Remove the TCC blank panel or the existing TCC card from slot 13 or 14 as shown in
TCC blank panel is installed, keep it for future use. To remove an existing TCC card, follow the
instructions in
Figure 5-10
RFGW-10-PWR-DC1
1
Two TCC cards
Step 5
To install a TCC card, turn the module sideways with the board facing right, grasp the TCC card front
panel with one hand and place your other hand under the sheet metal carrier edge to support the TCC
card. Do not touch the printed circuit boards or the connector pins.
Step 6
Align the edges of the TCC card sheet metal carrier edges with the slot guides on the top and bottom of
the Cisco RFGW-10 UEQAM chassis.
Cisco RF Gateway 10 Hardware Installation Guide
5-20
"Removing the TCC Card" section on page
TCC Card Slot Locations in the Cisco RFGW-10 Chassis
FAN OK
CAUTION: HIGH SPEED FAN ASSEMBLY
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 3
RF SLOT 12
RF SLOT 12
RF SLOT 3
PS1
SWITCH MUST BE IN THE OFF -O- POSITION PRIOR TO INSTALLING THE POWER SUPPLY
CAPTIVE FASTENERS MUST BE FULLY ENGAGED PRIOR
TO OPERATING THE POWER SUPPLY
-48V1
-48V2
FAN
FAL
FAULT
CUR LIM FAIL
TEMP FAIL
INPUT 2
INPUT 1
OUTPUT OK
-48 -60
-48V
-48V
WITH THE POWER
TURNED OFF
UNPLUG PEM FROM
SYSTEM BEFORE
CONNECTING OR
DISCONNECTION
RTN
RTN
POWER LUGS
RFGW-10-PWR-DC1
5-22.
RFGW-10-FAN-ASSY
14
13
RF SW 1
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
POWER
POWER
POWER
RFGW-10-RFSW1
STATUS
STATUS
POWER
MAINT
MAINT
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
POWER
DTI2
DTI2
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
DTI1
DTI1
POWER
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
POWER
RFGW-10-RFSW1
POWER
RF SW 12
PS2
SWITCH MUST BE IN THE OFF -O- POSITION PRIOR TO INSTALLING THE POWER SUPPLY
CAPTIVE FASTENERS MUST BE FULLY ENGAGED PRIOR
TO OPERATING THE POWER SUPPLY
-48V1
-48V2
FAN
FAL
FAULT
CUR LIM FAIL
TEMP FAIL
INPUT 2
INPUT 1
OUTPUT OK
-48 -60
-48V
-48V
WITH THE POWER
TURNED OFF
UNPLUG PEM FROM
SYSTEM BEFORE
CONNECTING OR
DISCONNECTION
RTN
RTN
POWER LUGS
Chapter 5
Installing and Removing FRUs
Figure
1
5-10. If a
OL-16264-04
Advertisement
Table of Contents
