Page 1 Dell Command Line Reference Guide for the S4810 System 9.4(0.0)
Page 2 WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell and the Dell logo are trademarks of Dell Inc.
Page 3: Table Of Contents
Contents 1 About this Guide..................... 43 ............................43 Objectives ..............................43 Audience ............................43 Conventions ..........................44 Information Icons 2 CLI Basics........................45 ......................45 Accessing the Command Line ......................45 Multiple Configuration Users ............................ 46 Obtaining Help ..........................48 Navigating the CLI ......................48 Using the Keyword no Command .........................
Page 6 6 802.1X........................183 ............................184 debug dot1x ...........................184 dot1x auth-fail-vlan ..........................186 dot1x auth-server ....................... 186 dot1x auth-type mab-only ....................187 dot1x authentication (Configuration) ....................... 188 dot1x authentication (Interface) ..........................189 dot1x guest-vlan ..........................190 dot1x host-mode ........................191 dot1x mac-auth-bypass ........................... 192 dot1x max-eap-req ........................193 dot1x max-supplicants...
Page 10 10 Border Gateway Protocol.................377 ........................377 BGP IPv4 Commands ..........................377 address-family ........................378 aggregate-address ..........................380 bgp add-path ......................381 bgp always-compare-med ..........................382 bgp asnotation ...................... 383 bgp bestpath as-path ignore ..................384 bgp bestpath as-path multipath-relax ......................384 bgp bestpath med confed ...................
Page 17 19 Force10 Resilient Ring Protocol (FRRP)............675 ............................675 clear frrp ............................676 debug frrp ............................677 description ............................... 678 disable ............................679 interface ............................ 680 member-vlan ..............................681 mode ............................682 protocol frrp ............................682 show frrp ..............................684 timer 20 GARP VLAN Registration (GVRP)..............687 ...........................
Page 18 23 Internet Group Management Protocol (IGMP)........... 715 ..........................715 IGMP Commands ........................715 clear ip igmp groups ..........................716 debug ip igmp ........................717 ip igmp access-group ......................718 ip igmp group-join-limit ......................719 ip igmp immediate-leave ..................720 ip igmp last-member-query-interval ......................721 ip igmp querier-timeout .........................722 ip igmp query-interval...
Page 30 41 Policy-based Routing (PBR)................1271 ............................1271 description ..........................1272 ip redirect-group ..........................1273 ip redirect-list ...............................1273 permit .............................1275 redirect ..............................1276 ..........................1278 show cam pbr ........................1279 show ip redirect-list 42 PIM-Sparse Mode (PIM-SM)................1281 ....................1281 IPv4 PIM-Sparse Mode Commands ......................
Page 37 54 Simple Network Management Protocol (SNMP) and Syslog....1553 ...........................1553 SNMP Commands ..........................1554 show snmp ........................ 1555 show snmp engineID ........................1555 show snmp group ........................1556 show snmp user ......................1557 snmp ifmib ifalias long ......................1558 snmp-server community ........................
Page 38 55 SNMP Traps......................1599 56 Stacking......................1605 ....................1605 redundancy disable-auto-reboot ....................1606 redundancy force-failover stack-unit ........................1607 redundancy protocol ..........................1607 reset stack-unit ........................... 1609 show redundancy ........................1610 show system stack-ports ..........................1612 stack-unit priority .........................1613 stack-unit provision ........................1614 stack-unit stack-group ......................1615 upgrade system stack-unit 57 Storm Control....................
Page 43: About This Guide
Release Notes Objectives This book is intended as a reference guide for the Dell Networking OS CLI commands, with detailed syntax statements, along with usage information and sample output. NOTE: For more information about when to use the CLI commands, refer to the Dell Networking OS Configuration Guide for your system.
Page 44: Information Icons
Keywords and parameters within brackets are optional. Keywords and parameters separated by a bar require you to choose one option. x||y Keywords and parameters separated by a double bar allows you to choose any or all of the options. Information Icons This book uses the following information symbols: NOTE: The Note icon signals important operational information.
Page 45: Cli Basics
CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
Page 46: Obtaining Help
When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2. Obtaining Help As soon as you are in a command mode there are several ways to access help.
Page 47 Use either the Backspace key or Delete key to erase the previous character. • To navigate left or right in the Dell Networking OS command line, use the left and right Arrow keys. The shortcut key combinations at the Dell Networking OS command line are as follows:...
Page 48: Navigating The Cli
Dell Networking OS displays a CLI prompt comprised of the host name and CLI mode. • Host name is the initial part of the prompt and is “Dell” by default. You can change the host name with the hostname command.
Page 49: Enabling Software Features On Devices Using A Command Option
You can filter a single command output multiple times. To filter a command output multiple times, place the save option as the last filter. For example: Dell# command | grep regular-expression | except regular-expression | grep other-regular-expression | find regular- expression | no-more | save.
Page 50: Feature Vrf
NOTE: The MXL and Z9000 platforms currently do not support VRF. These platforms support only the management and default VRFs, which are available by default. As a result, the feature vrf command is not available for these platforms. To display the state of Dell Networking OS features: Dell#show feature Example of show feature output...
Page 51: Command Modes
You can activate VRF application on a device by using the feature vrf command Information in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms. Example Dell#show feature Feature State ------------------------------ enabled Command Modes To navigate and launch various CLI modes, use specific commands.
Page 52: Dhcp Mode
Enter the configure command. The prompt changes to include (conf). From this mode, you can enter INTERFACE mode by using the interface command. CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, refer to Control Plane Policing (CoPP).
Page 53 EXEC Privilege mode, which is used to configure the device. When you are in EXEC mode, the > prompt is displayed following the host name prompt, which is “Dell” by default. You can change the host name prompt using the hostname command.
Page 54: Interface Mode
Enter the interface command and then enter an interface type and interface number that is available on the switch. The prompt changes to include the designated interface and slot/port number. For example: Prompt Interface Type Dell(conf-if)# INTERFACE mode Gigabit Ethernet interface then the slot/port information Dell(conf-if- gi-0/0)# Ten-Gigabit Ethernet interface then slot/port information...
Page 55: Lldp Mode
Prompt Interface Type Management Ethernet interface then slot/port information Dell(conf-if- ma-0/0)# Tunnel interface then tunnel ID. Dell(conf-if- tu-0)# Designated interface range (used for bulk configuration). Dell(conf-if- range)# IP ACCESS LIST Mode To enter IP ACCESS LIST mode and configure either standard or extended access control lists (ACLs), use the ip access-list standard or ip access-list extended command.
Page 56: Monitor Session Mode
Enter the management-interface command. The prompt changes to include (conf-lldp-mgmtIf). LINE Mode To configure the console or virtual terminal parameters, use LINE mode. To enter LINE mode: Verify that you are logged in to CONFIGURATION mode. Enter the line command. Include the keywords console or vty and their line number available on the switch.
Page 57 Enter the openflow of-instance command then the OpenFlow ID number of the instance you want to create or configure. The prompt changes to include (conf-of-instance of-id). You can return to the CONFIGURATION mode by entering the exit command. Per-VLAN SPANNING TREE (PVST+) Plus Mode To enable and configure the Per-VLAN Spanning Tree (PVST+) protocol, use PVST+ mode.
Page 58 PROTOCOL GVRP Mode To enable and configure GARP VLAN Registration Protocol (GVRP), use PROTOCOL GVRP mode. For more information, refer to GARP VLAN Registration (GVRP). To enter PROTOCOL GVRP mode: Verify that you are logged in to CONFIGURATION mode. Enter the protocol gvrp command. The prompt changes to include (config-gvrp). You can return to CONFIGURATION mode by using the exit command.
Page 59 Verify that you are logged in to CONFIGURATION mode. Use the router bgp command then enter the AS number. The prompt changes to include (conf- router_bgp). You can return to CONFIGURATION mode by using the exit command. ROUTER ISIS Mode To enable and configure Intermediate System to Intermediate System (ISIS), use ROUTER ISIS mode.
Page 60: Vrrp Mode
To enable u-Boot mode, press any key when the following line appears on the console during a system boot: Hit any key to stop autoboot:. The prompt changes to include ( =>). For more information, refer to S4810 u-Boot. NOTE: You cannot use the Tab key to complete commands in u-Boot mode.
Page 61 UPLINK STATE GROUP Mode To enable and configure an uplink-state group, use UPLINK STATE GROUP mode. For more information, refer to Uplink Failure Detection (UFD). To enter UPLINK STATE GROUP mode: Verify that you are logged in to CONFIGURATION mode. Enter the uplink-state-group command then the group ID number.
Page 63: File Management
This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. boot system Tell the system where to access the Dell Networking OS image used to boot the system. S4810 Syntax...
Page 64 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 65: Copy
E-Series Original command. copy Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field). S4810 Syntax copy compressed-config source-file-url destination-file-url Parameters Enter the following location keywords and information:...
Page 66 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added the compressed-config parameter.
Page 67 Two existing exec mode CLIs are enhanced to display and store the running configuration in the compressed mode. Example Dell#copy running-config scp:/ Address or name of remote host []: 10.10.10.1 Destination file name [startup-config]? old_running User name to login remote host? sburgess...
Page 68: Delete
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 69: Format Flash (S-Series)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 70: Fsck Flash
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 71: Rename
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 72: Restore Factory-Defaults
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 73 After the restore is complete, the units power cycle immediately. CAUTION: There is no undo for this command. Example (all Dell#restore factory-defaults stack-unit all clear-all stack units) ************************************************************** * Warning - Restoring factory defaults will delete the...
Page 74: Show Boot System
Enter the keyword all to display the boot image information for all line cards and rpms. stack-unit Enter the keyword stack-unit followed by a number to display boot image information for a stack-unit. The S4810 range is from 0 to 11. File Management...
Page 75: Show Bootvar
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 76: Show File-Systems
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 77: Show Os-Version
Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series Version 7.5.1.0 Introduced on the C-Series E-Series Original command Example Dell#show file-systems Size(b) Free(b) Feature Type Flags Prefixes 63938560 51646464 dosFs2.0 MMC rw flash: 63938560 18092032 dosFs1.0 MMC rw slot0:...
Page 78 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 79: Show Running-Config
Usage NOTE: A filepath that contains a dot ( . ) is not supported. Information show running-config Display the current configuration and display changes from the default values. S4810 Syntax show running-config [entity] [configured] [status] Parameters entity (OPTIONAL) To display that entity’s current (non-default)
Page 80 for the current Ethernet CFM ethernet configuration for the current FEFD configuration fefd for the current FTP configuration for the current FRRP configuration frrp for the current FVRP configuration fvrp for the current GVRP configuration gvrp for the current host configuration host for hardware-monitor action-on-error hardware-...
Page 81 for the current OSPF configuration ospf for the current PIM configuration for the current input policy map policy-map- configuration input for the current output policy map policy-map- configuration output for the current port-channel failover- po-failover- group configuration group for the current prefix-list configuration prefix-list for the current privilege configuration privilege...
Page 82 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 83: Show Startup-Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 84: Show Version
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 85 48 GigabitEthernet/IEEE 802.3 interface(s) 4 Ten GigabitEthernet/IEEE 802.3 interface(s) Dell# Example Dell# (S4810) Dell#show version Dell Real Time Operating System Software Dell Operating System Version: 1.0 Dell Application Software Version: Z9K-ICC-PRIM-SYNC-8-3-11-173 Copyright (c) 1999-2012 by Dell Inc. All Rights Reserved. File Management...
Page 86: Upgrade
Copyright (c) 1999-2014 by Dell Inc. All Rights Reserved. Build Time: Tue Mar 18 10:32:02 PDT 2014 Build Path: /work.local/build/buildSpaces/build01/E9-4-0/SW/ SRCC Dell Networking OS uptime is 1 day(s), 0 hour(s), 19 minute(s) System image file is "DT-MAA-S6000-16-PI" System Type: S6000 Control Processor: Intel Centerton with 3203911680 bytes of memory, core(s) 2.
Page 87 Enter the keywords stack-unit: to synch the image to the stack-unit. file-url Enter the following location keywords and information to upgrade using an Dell Networking OS image other than the one currently running: • To specify an Dell Networking OS image on the internal flash, enter flash:// file-path/filename.
Page 88 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Added support for IPv6 for the file-url parameter.
Page 91: Control And Monitoring
Control and Monitoring This chapter contains the commands to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP) as they apply to the following Dell Networking S4810 platform. NOTE: Starting in version 8.3.10.0, the enable xfp-power-updates command was deprecated for the S4810.
Page 92: Cam-Acl
Version 8.3.11.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Usage You must save the configuration and reload the system to implement ASF. When Information you enter the command, the system sends a message stating that the new mode is enabled when the system reloads.
Page 93 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 94: Cam-Acl-Vlan
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1. Introduced on S4810.
Page 95: Configure
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 96: Disable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 97 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 98: Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 99: Enable Optic-Info-Update Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 100: Enable Xfp-Power-Updates
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Deprecated command for S4820T. Replaced by the enable 8.3.19.0...
Page 101: End
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 102: Exec-Banner
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 103: Exit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 104: Ftp-Server Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 105 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 106: Ftp-Server Topdir
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 107: Ftp-Server Username
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 108: Hostname
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 109: Ip Ftp Password
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 110: Ip Ftp Source-Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 111: Ip Ftp Username
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 112: Ip Ftp Vrf
— sets the password for FTP connections. Commands ip ftp vrf Configures an FTP client with a VRF that is used to connect to the FTP server. S4810 Syntax ip ftp [vrf vrf-name] To undo the FTP client configuration, use the ip ftp [vrf vrf-name] command.
Page 113: Ip Telnet Server Vrf
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 114: Ip Telnet Source-Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Control and Monitoring...
Page 115: Ip Telnet Vrf
Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094).
Page 116: Ip Tftp Source-Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Verison Introduced on the S4820T.
Page 117: Ip Tftp Vrf
Original command ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. S4810 Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command.
Page 118: Line
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 119: Motd-Banner
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 120: Ping
Test connectivity between the system and another device by sending echo requests and waiting for replies. S4810 Syntax ping [host | ip-address | ipv6-address] [count {number | continuous}] [datagram-size] [timeout] [source (ip src-ipv4- address) | interface] [tos] [df-bit (y|n)] [validate-reply(y|...
Page 121 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Control and Monitoring...
Page 122 Added support for the outgoing-interface option for link-local IPv6 addressing on the S4820T. Version Added support for the outgoing-interface option for 8.3.12.0 link-local IPv6 addressing on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
Page 123: Reload
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 124: Send
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 125: Service Timestamps
Version Introduced on the S4810. 8.3.12.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced on the E-Series. Usage Messages can contain an unlimited number of lines; however, each line is limited Information to 255 characters.
Page 126: Show Alarms
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 127: Show Cam-Acl-Vlan
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version 8.3.11.1 Introduced on the Z9000.
Page 128: Show Command-History
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1. Introduced on S4810.
Page 129 Example Dell#show command-history [11/20 15:47:22]: CMD-(CLI):[service password-encryption]by default from console [11/20 15:47:22]: CMD-(CLI):[service password-encryption hostname Force10]by default from console - Repeated 3 times. [11/20 15:47:23]: CMD-(CLI):[service timestamps log datetime]by default from console [11/20 15:47:23]: CMD-(CLI):[hostname Force10]by default from console [11/20 15:47:23]: CMD-(CLI):[enable password 7 ******]by...
Page 130: Show Command-Tree
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 131: Show Cpu-Traffic-Stats
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 132: Show Debugging
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 133: Show Environment
Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series E-Series Original command.
Page 134 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 135: Show Inventory
Sensor3 Sensor4 Sensor5 Sensor6 --------------------------------------------------------------- -------------------- show inventory Display the S-Series or Z-Series switch type, components (including media), and Dell Networking Operating System (OS), including hardware identification numbers and configured protocols. S4810 Syntax show inventory [media slot] Parameters media slot...
Page 136 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 137: Show Memory
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Control and Monitoring...
Page 138: Show Processes Cpu
8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced this version of the command for the S-Series. Usage The output for show memory displays the memory usage of LP part (sysdlp) of the Information system.
Page 139 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 140 0.00% 0.00% 0.00% sysReaper 0xbae22000 10000 0.00% 0.00% 0.02% Dell#show processes cpu management-unit ? <1-99> Number of tasks with highest CPU usage last 5 seconds details Detail CPU utilization Pipe through a command Dell#show processes cpu management-unit details CPUID 5sec...
Page 141 0.00% 0.00% 0.00% dpi_cmow 0.00% 0.00% 0.00% dpi_taskcmo Dell#show processes cpu management-unit details ? Pipe through a command Dell#show processes cpu management-unit ? <1-99> Number of tasks with highest CPU usage last 5 seconds details Detail CPU utilization Pipe through a command...
Page 142: Show Processes Ipc Flow-Control
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 143 In the S-Series example, a retry (Retries) value of zero indicates that the SWP mechanism reached the maximum number of retransmissions without an acknowledgement. Example (S- Dell#show processes ipc flow-control ? Series) Control Processor Pipe through a command Control and Monitoring...
Page 144: Show Processes Memory
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 145 • In the output of this command, the memory size is equal to the size of the application processes plus the size of the system processes. Example Dell#show processes memory stack-unit 0 Total: 268435456, MaxUsed: 2420244, CurrentUsed: 2420244, CurrentFree: 266015212...
Page 146: Show Software Ifm
Example Dell#show processes management-unit (management- Total : 151937024, MaxUsed : 111800320 [2/25/2008 unit) 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 331 vrrp 5189632 249856 50572...
Page 147 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 148: Show System
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for the disabled-ports parameter .
Page 149 Piece Part ID (PPID). Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 The Boot Flash field displays the code level for boot code 2.8.1.1 and newer, while older boot codes display as "Present".
Page 151 7021 7021 7021 7021 Speed in RPM Related • show version – displays the Dell Networking OS version. Commands • show processes memory (S-Series) – displays the memory usage based on running processes. • show hardware stack-unit – displays the data plane and management plane input and output statistics of a particular stack member.
Page 152: Show Tech-Support
Display a collection of data from other show commands, necessary for Dell Networking technical support to perform troubleshooting on S-Series or Z-Series switches. S4810 Syntax show tech-support [stack-unit unit-id | page] Parameters stack-unit (OPTIONAL) Enter the keywords stack-unit to view CPU memory usage for the stack member designated by unit-id.
Page 153 Show only text that matches a pattern no-more Don't paginate output save Save output to a file Dell#show tech-support stack-unit 1 | save ? flash: Save to local file system (flash://filename (max 20 chars) ) Dell#show tech-support stack-unit 1 | save flash://LauraSave Start saving show command report ..
Page 154 Dell Real Time Operating System Software Dell Operating System Version: Dell Application Software Version: 9-4(0-168) Copyright (c) 1999-2014 by Dell Inc. All Rights Reserved. Build Time: Sun Mar 23 22:17:49 PDT 2014 Build Path: /work.local/build/buildSpaces/build01/E9-4-0/SW/SRC Dell Networking OS uptime is 32 minute(s) System image file is "s6000"...
Page 155: Ssh-Peer-Stack-Unit
Introduced on the S-Series. telnet Connect through Telnet to a server. The Telnet client and server in Dell Networking support IPv4 and IPv6 connections. You can establish a Telnet session directly to the router or a connection can be initiated from the router.
Page 156 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Control and Monitoring...
Page 157: Telnet-Peer-Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 158: Terminal Length
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 159: Traceroute
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 160 (default is 64). Example (IPv4) Dell#traceroute www.Dell Networking.com Translating "www.Dell Networking.com"...domain server (10.11.0.1) [OK] Type Ctrl-C to abort. ----------------------------------------------- Tracing the route to www.Dell Networking.com (10.11.84.18), 30 hops max, 40 byte packets ----------------------------------------------- TTL Hostname Probe1 Probe2 Probe3 10.11.199.190 001.000 ms 001.000 ms 002.000 ms...
Page 161: Undebug All
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 162 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 163: Write
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 165: 802.1Ag
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 166: Clear Ethernet Cfm Traceroute-Cache
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 167: Database Hold-Time
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 168: Domain
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 169: Ethernet Cfm Mep
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 170: Ethernet Cfm Mip
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 171: Mep Cross-Check
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 172: Mep Cross-Check Start-Delay
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 173: Ping Ethernet
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 174: Show Ethernet Cfm Maintenance-Points Local
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 175: Show Ethernet Cfm Maintenance-Points Remote
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 176: Show Ethernet Cfm Mipbd
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 177: Show Ethernet Cfm Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 178: Show Ethernet Cfm Port-Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 179: Show Ethernet Cfm Traceroute-Cache
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 180: Traceroute Cache Hold-Time
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 181: Traceroute Cache Size
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 182 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 183: 802.1X
802.1X Port Authentication. Important Points to Remember Dell Networking operating software limits network access for certain users by using virtual local area network (VLAN) assignments. 802.1X with VLAN assignment has these characteristics when configured on the switch and the RADIUS server.
Page 184: Debug Dot1X
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 185 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 186: Dot1X Auth-Server
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 187: Dot1X Authentication (Configuration)
Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. 802.1X...
Page 188: Dot1X Authentication (Interface)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 189: Dot1X Guest-Vlan
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 190: Dot1X Host-Mode
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 191: Dot1X Mac-Auth-Bypass
— Display the 802.1X configuration of an interface. Commands dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell Networking OS attempts to authenticate the host based on its MAC address. S4810 Syntax dot1x mac-auth-bypass To disable MAC authentication bypass on a port, use the no dot1x mac-auth- bypass command.
Page 192: Dot1X Max-Eap-Req
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 193: Dot1X Max-Supplicants
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 194: Dot1X Quiet-Period
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 195: Dot1X Reauthentication
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 196: Dot1X Reauth-Max
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 197: Dot1X Server-Timeout
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 198: Dot1X Supplicant-Timeout
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 199: Dot1X Tx-Period
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 200 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 201: Show Dot1X Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 202 Re-Auth Interval: 3600 seconds Max-EAP-Req: Auth Type: SINGLE_HOST Auth PAE State: Initialize Backend State: Initialize Dell# Example (mac- Dell#show dot1x interface gig 2/21 mac-address address) 00:00:01:00:07:00 802.1x information on Gi 2/21: ----------------------------- Dot1x Status: Enable Port Control: AUTO Re-Authentication: Disable...
Page 203 Authenticated Backend State: Idle Port status and State info for Supplicant: 00:00:00:00:00:11 192 | 802.1X www.dell.com | s u p p o r t . d e l l.com Port Auth Status: AUTHORIZED Untagged VLAN id: Auth PAE State: Authenticated...
Page 205: Access Control Lists (Acl)
Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell Networking operating software on the S4810 platform. Dell Networking OS supports the following types of ACL, IP prefix list, and route maps: • Commands Common to all ACL Types •...
Page 206 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 207: Show Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 208: Access-Class
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 209: Ip Access-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 210 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 211: Ip Control-Plane Egress-Filter
Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. show ip accounting access-list Display the IP access-lists created on the switch and the sequence of filters. S4810 Syntax show ip accounting {access-list access-list-name | cam_count}...
Page 212 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 213: Show Ip Access-Lists
15 deny ip any 191.3.0.0 /16 seq 20 deny ip any 191.4.0.0 /16 seq 25 deny ip any 191.5.0.0 /16 Dell#show ip accounting access-list L3-ACL vrf vrf3 Standard Ingress IP access list L3-ACL on vrf3 Total cam count 3 seq 5 permit 10.1.2.0/24...
Page 214: Standard Ip Acl Commands
When you create an ACL without any rule and then apply it to an interface, the ACL behavior reflects an implicit permit. The S4810 supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types Common IP ACL Commands sections.
Page 215 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 216: Ip Access-List Standard
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 217: Permit
Dell Networking OS supports one ingress and one egress IP ACL per interface. Information Prior to Dell Networking OS version 7.8.1.0, names are up to 16 characters long. The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation.
Page 218 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 219: Resequence Access-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 220: Seq
Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. S4810 Syntax seq sequence-number {deny | permit} {source [mask] | any | host ip-address}} [count [bytes]] [dscp value] [order] [fragments] To delete a filter, use the no seq sequence-number command.
Page 221 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 222: Extended Ip Acl Commands
The following commands configure extended IP ACLs, which in addition to the IP address, also examine the packet’s protocol type. The S4810 supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types Common IP ACL Commands sections.
Page 223 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 224: Deny Icmp
The order option is relevant in the context of the Policy QoS feature only. For Information more information, refer to the Quality of Service chapter of the Dell Networking OS Configuration Guide. When you use the log option, the CP processor logs detail the packets that match.
Page 225 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 226: Deny Tcp
The order option is relevant in the context of the Policy QoS feature only. For Information more information, refer to the Quality of Service chapter of the Dell Networking OS Configuration Guide. The monitor option is relevant in the context of flow-based monitoring only. For...
Page 227 dscp Enter this keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. Enter a flag or combination of bits: • ack: acknowledgement field • fin: finish (no more data from the user) •...
Page 228 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 229: Deny Udp
— assigns a filter to deny UDP traffic. deny udp To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter. S4810 Syntax deny udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [dscp]...
Page 230 To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny udp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. Parameters source Enter the IP address of the network or host from which the...
Page 231 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 232: Ip Access-List Extended
Commands deny tcp — assigns a filter to deny TCP traffic. ip access-list extended Name (or select) an extended IP access list (IP ACL) based on IP addresses or protocols. S4810 Syntax ip access-list extended access-list-name Access Control Lists (ACL)
Page 233 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 234: Permit
To pass IP packets meeting the filter criteria, configure a filter. S4810 Syntax permit {source mask | any | host ip-address} {destination mask | any | host ip-address} [count [bytes]] [dscp value] [order] [fragments] To remove this filter, you have two choices: •...
Page 235: Permit Tcp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 236 address} [bit] [dscp] [operator port [port]] [count [byte] | log] [order] [monitor] [fragments] To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command.
Page 237 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 238 The order option is relevant in the context of the Policy QoS feature only. For Information more information, refer to the “Quality of Service” chapter of the Dell Networking OS Configuration Guide. NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value.
Page 239: Permit Udp
— assigns a permit filter for UDP packets. permit udp To pass UDP packets meeting the filter criteria, configure a filter. S4810 Syntax permit udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [dscp]...
Page 240 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 241 The order option is relevant in the context of the Policy QoS feature only. For Information more information, refer to the “Quality of Service” chapter of the Dell Networking OS Configuration Guide. NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value.
Page 242: Resequence Access-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 243: Seq
[port]] [count [byte] | log] [dscp value] [order] [monitor] [fragments] Parameters sequence- Enter a number from 0 to 4294967290. For the S4810 , the number range is from 0 to 65534. deny Enter the keyword deny to configure a filter to drop packets meeting this condition.
Page 244 ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, refer to the Flow-based Monitoring section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. Access Control Lists (ACL)
Page 245 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 246: Common Mac Access List Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 247: Mac Access-Group
Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version Introduced on the E-Series.
Page 248 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 249: Show Mac Access-Lists
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 250: Show Mac Accounting Access-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 251: Standard Mac Acl Commands
When you create an access control list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit. These commands configure standard MAC ACLs. The S4810 support both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the...
Page 252 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 253: Mac Access-List Standard
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 254: Permit
Introduced on the E-Series. 6.1.1.0 Usage Dell Networking OS supports one ingress and one egress MAC ACL per interface. Information The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation.
Page 255 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 256: Seq
Dell Networking OS Configuration Guide. Defaults Not configured Command CONFIGURATION-MAC ACCESS LIST-STANDARD Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. Access Control Lists (ACL)
Page 257: Extended Mac Acl Commands
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
Page 258 mac-destination-address-mask} [ethertype-operator] [count [byte]] [log] [monitor] To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {any | host mac-address | mac-source-address mac-source-address-mask} {any | host mac-address | mac- destination-address mac-destination-address-mask} command.
Page 259: Mac Access-List Extended
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 260 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 261: Permit
Dell(config-ext-macl)#exit Dell(conf)#do show mac accounting access-list snickers interface g0/47 in Extended mac access-list snickers on GigabitEthernet 0/47 seq 10 permit any any ev2 eq 800 count bytes (559851886 packets 191402152148 bytes) seq 20 permit any any ev2 eq 806 count bytes (74481486 packets...
Page 262 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 263: Ip Prefix List Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Access Control Lists (ACL)
Page 264: Deny
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Access Control Lists (ACL)
Page 265: Ip Prefix-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 266: Seq
— displays a summary of the configured prefix lists. To a deny or permit filter in a prefix list while configuring the filter, assign a sequence number. S4810 Syntax seq sequence-number {deny | permit} {any} | [ip-prefix /nn {ge...
Page 267: Show Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 268: Show Ip Prefix-List Detail
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 269: Show Ip Prefix-List Summary
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 270: Route Map Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 271 Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
Page 272: Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 273: Match Community
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 274: Match Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 275: Match Ip Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 276 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 277: Match Ip Next-Hop
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 278: Match Ip Route-Source
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 279: Match Metric
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 280: Match Origin
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 281: Match Route-Type
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 282: Match Tag
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 283: Route-Map
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 284: Set As-Path
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 285: Set Automatic-Tag
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 286: Set Comm-List Delete
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 287: Set Community
— specifies a COMMUNITY attribute. set community Allows you to assign a BGP COMMUNITY attribute. S4810 Syntax set community {community-number | local-as | no-advertise | no- export | none} [additive] To delete a BGP COMMUNITY attribute assignment, use the no set community {community-number | local-as | no-advertise | no-export | none} command.
Page 288 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 289: Set Level
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Dell Networking OS Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 290: Set Local-Preference
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 291: Set Metric
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 292: Set Metric-Type
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 293: Set Next-Hop
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 294: Set Origin
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 295: Set Weight
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 296: Show Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 297: Show Route-Map
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 298: As-Path Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 299: Show Ip As-Path-Access-Lists
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 300: Ip Community List Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 301: Deny (For Standard Ip Acls)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 302 Command CONFIGURATION-STANDARD-ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 303: Deny (For Extended Ip Acls)
egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
Page 304 Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 305: Seq (For Standard Ipv4 Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 306: Deny Tcp (For Extended Ip Acls)
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction.
Page 307: Deny Udp (For Extended Ip Acls)
Added the support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added the support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 308 The default frequency at which ACL logs are generated is five minutes. Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 309: Deny Arp (For Extended Mac Acls)
Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 310: Deny Icmp (For Extended Ip Acls)
new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re- enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
Page 311 Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 312: Deny Ether-Type (For Extended Mac Acls)
Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 313: Deny (For Standard Mac Acls)
new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re- enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
Page 314 Command CONFIGURATION-MAC ACCESS LIST-STANDARD Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 315: Deny (For Extended Mac Acls)
Command CONFIGURATION-MAC ACCESS LIST-EXTENDED Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 316: Permit (For Standard Ip Acls)
new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re- enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
Page 317 Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 318: Permit Arp (For Extended Mac Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 319: Permit Ether-Type (For Extended Mac Acls)
If ACL logging is stopped because the configured threshold is exceeded, it is re- enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
Page 320: Permit Icmp (For Extended Ip Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 321 Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 322: Permit Udp (For Extended Ip Acls)
ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
Page 323: Permit (For Extended Ip Acls)
Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 324 Added the support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added the support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 325: Permit (For Standard Mac Acls)
enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic.
Page 326: Seq (For Standard Mac Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 327 Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 328: Permit Tcp (For Extended Ip Acls)
one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related deny — configures a filter to drop packets. Commands permit — configures a filter to forward packets. permit tcp (for Extended IP ACLs) To pass TCP packets meeting the filter criteria, configure a filter.
Page 329: Seq Arp (For Extended Mac Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 330 Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, History Z9000, and MXL 10/40GbE Switch IO Module platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms.
Page 331: Seq Ether-Type (For Extended Mac Acls)
egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
Page 332: Seq (For Ip Acls)
Command CONFIGURATION-EXTENDED-ACCESS-LIST Modes Command Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, History Z9000, and MXL 10/40GbE Switch IO Module platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms.
Page 333 Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 334: Seq (For Ipv6 Acls)
Command ACCESS-LIST Modes Command Version 9.4(0.0) Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Access Control Lists (ACL)
Page 335: Permit Udp (For Ipv6 Acls)
Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
Page 336 Command ACCESS-LIST Modes Command Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 337: Permit Tcp (For Ipv6 Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 338: Permit Icmp (For Ipv6 Acls)
If ACL logging is stopped because the configured threshold is exceeded, it is re- enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
Page 339: Permit (For Ipv6 Acls)
Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 340 Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 341: Deny Udp (For Ipv6 Acls)
ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
Page 342: Deny Tcp (For Ipv6 Acls)
S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 343 Added support for flow-based monitoring on the S4810, History S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 344: Deny Icmp (For Extended Ipv6 Acls)
monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
Page 345: Deny (For Ipv6 Acls)
Command ACCESS-LIST Modes Command Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Usage When the configured maximum threshold is exceeded, generation of logs is Information stopped.
Page 346 Command ACCESS-LIST Modes Command Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, History and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
Page 347 one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Access Control Lists (ACL)
Page 349: Access Control List (Acl) Vlan Groups And Content Addressable Memory (Cam)
None Command CONFIGURATION (conf-acl-vl-grp) Modes Command Version 9.3. Introduced on the S4810, S4820T, and Z9000 platforms. History (0.0) Usage At a maximum, there can be only 32 VLAN members in all ACL VLAN groups. A Information VLAN can belong to only one group at any given time.
Page 350: Ip Access-Group
Default None Command CONFIGURATION (conf-acl-vl-grp) Modes Command Version 9.3. Introduced on the S4810, S4820T, and Z9000 platforms. History (0.0) Usage You can apply only an egress IP ACL on an ACL VLAN group. Information show acl-vlan-group Display all the ACL VLAN groups or display a specific ACL VLAN group, identified by name.
Page 351 Command Version 9.3. Introduced on the S4810, S4820T, Z9000 and MXL platforms History (0.0) Usage When an ACL-VLAN-Group name or the Access List Group Name contains more Information than 30 characters, the name is truncated in the show acl-vlan-group command output.
Page 352: Show Cam-Acl-Vlan
Syntax show cam-acl-vlan Command EXEC Privilege Modes Command Version 9.3. Introduced on the S4810, S4820T, Z9000 and MXL History (0.0) platforms. Usage After CAM configuration for ACL VLAN groups is performed, you must reboot the Information system to enable the settings to be stored in nonvolatile storage. During the initialization of CAM, the chassis manager reads the NVRAM and allocates the dynamic VCAP regions.
Page 353: Cam-Acl-Vlan
Field Description VlanAclOpt Number of FP blocks for ACL VLAN optimzation feature. Example Dell#show cam-acl-vlan -- Chassis Vlan Cam ACL -- Current Settings(in block sizes) VlanOpenFlow : VlanIscsi VlanHp VlanFcoe VlanAclOpt : -- Stack unit 0 -- Current Settings(in block sizes)
Page 354: Show Cam-Usage
(OPTIONAL) Enter the keyword switch to display Layer 2 CAM usage. Command EXEC Modes EXEC Privilege Command Version 9.3. Introduced on the S4810, S4820T, Z9000 and MXL History (0.0) platforms. Usage The following regions must be provided in the show cam-usage output: Information •...
Page 355 Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs Example 1: Dell#show cam-usage Output of the Linecard|Portpipe| CAM Partition | Total CAM Used CAM |Available CAM...
Page 356 12286 | IN-L3 FIB 262141 262127 | IN-L3-SysFlow 2878 2834 --More-- Example 2: Dell#show cam-usage acl Output of the Linecard|Portpipe| CAM Partition | Total CAM Used CAM |Available CAM show cam- ========|========|=================|=============| usage acl =============|============ Command | IN-L2 ACL 1008...
Page 357: Show Running Config Acl-Vlan-Group
EXEC Modes EXEC Privilege Command Version 9.3. Introduced on the S4810, S4820T, Z9000 and MXL platforms History (0.0) Examples The following sample output shows the line-by-line style display when using the show running-config acl-vlan-group option. Note that no group or access...
Page 358: Acl-Vlan-Group
Command CONFIGURATION Modes Command Version 9.3(0.0) Introduced on the S4810, S4820T and Z9000 platforms History Usage You can have up to eight different ACL VLAN groups at any given time. When you Information configure an ACL VLAN group, you enter the ACL VLAN Group Configuration mode.
Page 359: Show Acl-Vlan-Group Detail
No default behavior or values Command EXEC Modes EXEC Privilege Command Version 9.3. Introduced on the S4810, S4820T, Z9000, and MXL History (0.0) platforms Usage The output for this command displays in a line-by-line format. This allows the ACL- Information VLAN-Group names (or the Access List Group Names) to display in their entirety.
Page 360: Description (Acl Vlan Group)
No default behavior or values Command CONFIGURATION (conf-acl-vl-grp) Modes Command Version 9.3. Introduced on the S4810, S4820T, and Z9000 platforms History (0.0) Usage Enter a description for each ACL VLAN group that you create for effective and Information streamlined administrative and logging purposes.
Page 361: Bidirectional Forwarding Detection (Bfd)
Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection. The Dell Networking operating software implementation is based on the standards specified in the IETF Draft draft-ietf-bfd-base-03 and supports BFD on all Layer 3 physical interfaces including VLAN...
Page 362 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 363: Bfd Disable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on S4810.
Page 364: Bfd Enable (Interface)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 365: Bfd Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 366: Bfd Neighbor
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 367: Bfd Protocol-Liveness
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 368 Command CONFIGURATION Modes Command Version 9.3. Introduced on S6000. History (0.0) Version 9.2. Introduced on Z9000, S4810, and S4820T. (0.0) Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. Related show bfd neighbors –...
Page 369: Ipv6 Ospf Bfd All-Neighbors
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2.0.0 Introduced on the Z9000, S4820T, and S4810.
Page 370: Isis Bfd All-Neighbors
To disable BFD on a specific interface while you configure BFD in CONFIGURATION mode, use the keyword disable. isis bfd all-neighbors Enable BFD on all IS-IS neighbors discovered on an interface. S4810 Syntax isis bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]]...
Page 371: Neighbor Bfd
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on Z9000.
Page 372: Neighbor Bfd Disable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 373: Show Bfd Neighbors
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 374 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 375: Vrrp Bfd Neighbor
Example Dell#show bfd neighbors detail (Detail) Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 10.1.3.2 Local MAC Addr: 00:01:e8:02:15:0e Remote Addr: 10.1.3.1 Remote MAC Addr: 00:01:e8:27:2b:f1 Int: GigabitEthernet 1/3 State: Up Configured parameters: TX: 100ms, RX: 100ms, Multiplier: 3 Neighbor parameters:...
Page 376 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 377: Border Gateway Protocol
(ASNs), where the 2-byte format is 1 to 65535 and the 4-byte format is 1 to 4294967295. NOTE: Dell Networking OS supports dotted format as well as the traditional plain format for AS numbers. The dot format is displayed when using the show ip bgp commands. To determine the comparable dot format for an ASN from a traditional format, use ASN/65536.
Page 378: Aggregate-Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 379 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 380: Bgp Add-Path
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Border Gateway Protocol...
Page 381: Bgp Always-Compare-Med
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 382: Bgp Asnotation
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 383: Bgp Bestpath As-Path Ignore
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 384: Bgp Bestpath As-Path Multipath-Relax
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 385: Bgp Bestpath Med Missing-As-Best
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 386: Bgp Bestpath Router-Id Ignore
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 387: Bgp Cluster-Id
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 388: Bgp Confederation Identifier
Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage When a BGP cluster contains only one route reflector, the cluster ID is the route Information reflector’s router ID.
Page 389 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 390: Bgp Confederation Peers
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 391: Bgp Connection-Retry-Timer
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Introduced on the S4810.
Page 392 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 393: Bgp Default Local-Preference
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 394: Bgp Enforce-First-As
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 395: Bgp Fast-External-Fallover
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 396: Bgp Graceful-Restart
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 397: Bgp Non-Deterministic-Med
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 398: Bgp Recursive-Bgp-Next-Hop
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 399: Bgp Regex-Eval-Optz-Disable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 400 Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced Usage BGP uses regular expressions (regex) to filter route information.
Page 401: Bgp Router-Id
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 402 Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to clear all BGP sessions corresponding to that VRF. NOTE: Use this attribute to clear a BGP instance corresponding to either a specific address family in a default VRF or an IPv4 address family in a a non-default VRF.
Page 403: Clear Ip Bgp Dampening
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 404: Clear Ip Bgp Flap-Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 405 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 406: Clear Ip Bgp Peer-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 407: Debug Ip Bgp
Version 7.7.1.0 Introduced on the C-Series. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, and updates. S4810 Syntax debug ip bgp [ vrf vrf-name | ip-address | peer-group peer- group-name] [in | out] To disable all BGP debugging, use the no debug ip bgp command.
Page 408: Debug Ip Bgp Dampening
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 409: Debug Ip Bgp Events
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 410: Debug Ip Bgp Keepalives
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 411: Debug Ip Bgp Notifications
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 412: Debug Ip Bgp Soft-Reconfiguration
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 413: Debug Ip Bgp Updates
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 414: Default-Metric
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 415: Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 416: Neighbor Activate
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 417: Neighbor Add-Path
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 418: Neighbor Advertisement-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 419: Neighbor Advertisement-Start
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 420: Neighbor Allowas-In
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 421: Neighbor Default-Originate
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 422: Neighbor Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 423: Neighbor Distribute-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 424: Neighbor Ebgp-Multihop
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 425: Neighbor Fall-Over
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 426: Neighbor Local-As
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 427: Neighbor Maximum-Prefix
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Border Gateway Protocol...
Page 428: Neighbor Password
Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage If you configure the neighbor maximum-prefix command and the neighbor...
Page 429 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 430: Neighbor Peer-Group (Assigning Peers)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 431: Neighbor Peer-Group (Creating Group)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 432: Neighbor Peer-Group Passive
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 433: Neighbor Remote-As
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 434: Neighbor Remove-Private-As
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 435: Neighbor Route-Map
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Added 4-byte support. Usage Applies to EBGP neighbors only. Information Configure your system to accept 4-byte formats before entering a 4 byte AS Number.
Page 436: Neighbor Route-Reflector-Client
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 437: Neighbor Sender-Side-Loopdetect
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 438 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 439: Neighbor Shutdown
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 440: Neighbor Soft-Reconfiguration Inbound
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 441: Neighbor Timers
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 442: Neighbor Update-Source
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 443: Neighbor Weight
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 444: Network
Usage In the Dell Networking OS best path selection process, the path with the highest Information weight value is preferred. NOTE: In the Dell Networking OS best-path selection process, the path with the highest weight value is preferred. If you configure the set weight command in a route map applied to this neighbor, the weight set in that command overrides the weight set in the neighbor weight command.
Page 445: Network Backdoor
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 446: Redistribute
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 447 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 448: Redistribute Ospf
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Border Gateway Protocol...
Page 449: Router Bgp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 450: Show Capture Bgp-Pdu Neighbor
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 451: Show Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 452: Show Ip Bgp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 453 Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series.
Page 454: Show Ip Bgp Cluster-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 455 0 500 i *>I 77.0.0.0/24 172.16.0.2 Dell#show ip bgp cluster-list 4.4.4.4 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.6 Status codes: s suppressed, S stale, d dampened, h history, * valid, >...
Page 456: Show Ip Bgp Community
View information on all routes with Community attributes or view specific BGP community groups. S4810 Syntax show ip bgp [vrf vrf-name] [ipv4 unicast] community [community- number] [local-as] [no-export] [no-advertise] Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of...
Page 457 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 458: Show Ip Bgp Community-List
66.0.0.0/24 172.16.0.2 0 200 i Dell#show ip bgp community no-advertise BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, >...
Page 459 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 460: Show Ip Bgp Dampened-Paths
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for VRF.
Page 461: Show Ip Bgp Detail
Lists all the ASs the dampened route passed through to reach the destination network. Example Dell#show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, >...
Page 462 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 463 0x41a1b6e4 RxUpdCodeP 0x41a1b704 : TxEcodeP 0x41a1b734 : TxHdrcodeP 0x41a1b750 : TxOpCodeP 0x41a1b760 TxUpdCodeP 0x41a1b780 : TrEvt 0 : LocPref 100 : tmpPathP 0x41a1b7b8 : LogNbrChgs 1 RecursiveNH 1 : PgCfgId 0 : KeepAlive 0 : HldTime 0 : DioHdl 0 : AggrValTmrP 0x41ee7024 UpdNetTmrP 0 : RedistTmrP 0x41ee7094 : PeerChgTmrP 0 : CleanRibTmrP 0x41ee7104...
Page 464: Show Ip Bgp Extcommunity-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 465: Show Ip Bgp Filter-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Border Gateway Protocol...
Page 466 Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage The following describes the show ip bgp filter-list hello command Information shown in the following example.
Page 467: Show Ip Bgp Flap-Statistics
0 200 400 500 600 i *> 66.0.0.0/24 172.16.0.2 0 200 500 i show ip bgp flap-statistics View flap statistics on BGP routes. S4810 Syntax show ip bgp [vrf vrf-name] [ipv4 unicast] flap-statistics [ip- address [mask]] [filter-list as-path-name] [regexp regular- expression] Parameters vrf vrf-name...
Page 468 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 469: Show Ip Bgp Inconsistent-As
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 470 0 18508 209 701 i 63.114.8.34 0 18508 209 701 i --More-- Dell>sho ip bgp vrf testinconsistent-as BGP table version is 11, local router ID is 66.66.77.77 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best...
Page 471: Show Ip Bgp Neighbors
0.0.0.0 32768 i show ip bgp neighbors Allows you to view the information BGP neighbors exchange. S4810 Syntax show ip bgp [vrf vrf-name] [ipv4 unicast] neighbors [ip-address [advertised-routes | dampened-routes | detail | flap-statistics | routes | {received-routes [network [network-mask]]} |...
Page 472 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 473 exception where neighbor information corresponding to ignored updates is displayed. BGP shows the exact information that is exchanged between the BGP peers. It also indicates whether or not this information is received by the BGP peer. The following describes the show ip bgp neighbors command shown in the following examples.
Page 474 Foreign host: Displays the peering address of the neighbor and the TCP port number. Example Dell#show ip bgp neighbors 172.16.0.2 BGP neighbor is 172.16.0.2, remote AS 200, external link Member of peer-group port0 for session parameters BGP remote router ID 172.16.0.2...
Page 475: Show Ip Bgp Next-Hop
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 476: Show Ip Bgp Paths
Next-hop Resolved 172.16.0.2 Dell# show ip bgp paths View all the BGP path attributes in the BGP database. S4810 Syntax show ip bgp[vrf vrf-name] paths [regexp regular-expression] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf to view all path attributes in the BGP database corresponding to that VRF.
Page 477 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for VRF for the S4810, S4820T, and S6000.
Page 478: Show Ip Bgp Paths Community
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 479: Show Ip Bgp Peer-Group
Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these communities. Community Displays the community attributes in this BGP path. Example Dell#show ip bgp paths community Total 2 communities Refcount Community NO-ADVERTISE 200:1 1000:1...
Page 480 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 481: Show Ip Bgp Regexp
Commands neighbor peer-group (creating group) — creates a peer group. show ip bgp regexp Display the subset of the BGP routing tables matching the regular expressions specified. S4810 Syntax show ip bgp [vrf vrf-name] regexp regular-expression [character] Parameters vrf vrf-name...
Page 482 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 483: Show Ip Bgp Summary
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 484 If two peers send the same route that contains similar path attributes, then two entries are maintained in the back-end, as both these entries have different next- hops. If this same route is sent to a different peer, an entry for each peer is created, as the next-hop is different.
Page 485 If the neighbor is disabled, the phrase (Admin shut) appears in this column. Example Dell#show ip bgp summary (S4810) BGP router identifier 192.168.11.5, local AS number 100 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0...
Page 486: Show Running-Config Bgp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 487: Mbgp Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 488: Distance Bgp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 489: Show Ip Bgp Dampened-Paths
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 490 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for VRF.
Page 491: Bgp Extended Communities (Rfc 4360)
(OPTIONAL) Enter the keywords non-trans to indicate a non-transitive BGP extended community. Defaults none Command ROUTE MAP (config-route-map) Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. Border Gateway Protocol...
Page 492: Set Extcommunity Soo
The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T 8.3.19.0 Version 8.3.11.1 Introduced on the Z-9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series.
Page 493: Show Ip Bgp Paths Extcommunity
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 494: Show Ip Extcommunity-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Border Gateway Protocol...
Page 495: Ipv6 Bgp Commands
Dell# IPv6 BGP Commands IPv6 border gateway protocol (IPv6 BGP) is supported on the S4810 platform. BGP is an external gateway protocol that transmits interdomain routing information within and between Autonomous Systems (AS). Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically send messages to update those routing tables.
Page 496: Debug Ip Bgp Ipv6 Unicast Soft-Reconfiguration
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 497: Ipv6 Prefix-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 498: Neighbor Soft-Reconfiguration Inbound
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.4.1.0 Added support for IPv4 multicast and IPv4 unicast address families.
Page 499: Show Ipv6 Prefix-List
FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version 9.0.0.0 Introduced on the Z9000. Version Introduced on the S4810. 8.3.10.0 Related ipv6 prefix-list — configures an IPv6 prefix-list.
Page 500 FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version 9.0.0.0 Introduced on the Z9000. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.10.0 Border Gateway Protocol...
Page 501: Content Addressable Memory (Cam)
NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell Networking Technical Assistance Center (TAC) for guidance.
Page 502 DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, OpenFlow, and Policy-based Routing (PBR). S4810 Syntax cam-acl {default | l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number [vman- qos | vman-dual-qos number] ecfmacl number ipv4pbr...
Page 503 ecfmacl Enter the keyword ecfmacacl and then the number of FP number blocks for ECFM ACL. The range is from 0 to 5. Vman-qos| Enter the keyword evman-qos and then the number of FP vman-dual-qos blocks for VMAN QoS. The range is from 0 to 6. number vman-dual-qos Enter the keyword vman-dual-qos and then the number of...
Page 504 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for PBR and VRF.
Page 505: Cam-Acl-Egress
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.. Version 9.0.2.0 Introduced on the S6000.
Page 506: Show Cam-Acl
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 507 Example -- Chassis Cam ACL -- (S4810 Default) Current Settings(in block sizes) 1 block = 128 entries L2Acl Ipv4Acl Ipv6Acl Ipv4Qos L2Qos L2PT IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl -- Stack unit 0 -- Current Settings(in block sizes)
Page 508: Test Cam-Usage
Enter all to get information for all the linecards/stack-units or enter the linecard/ stack-unit number to get information for a specific card. The range is : 0-11 for S4810; 0-7 for all other S-Series Defaults none Command...
Page 509 0 | 0 | IPv4Flow | 102 | 0| Allowed 0 | 1 | IPv4Flow | 102 | 0| Allowed Dell# Dell#test cam-usage service-policy input In stack-unit 0 port- set 1 Stack-Unit | Portpipe | CAM Partition | Available CAM |...
Page 510 0 | 1 | IPv4Flow | 102 | 0| Allowed Dell# Usage The following describes the test cam-usage command shown in the Example Information below. Term Explanation Stack-Unit Lists the stack unit or units that are checked. Entering all shows the status for all stacks.
Page 511: Control Plane Policing (Copp)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 512: Service-Policy Rate-Limit-Protocols
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 513: Ip Unknown-Unicast
Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810. Usage This command applies the service-policy based on the type of protocol defined in Information the ACL rules. Create ACL and QoS policies prior to enabling this command.
Page 514: Ipv6 Unknown-Unicast
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 515: Show Ip Protocol-Queue-Mapping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 516: Show Ipv6 Protocol-Queue-Mapping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 517: Show Mac Protocol-Queue-Mapping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 519: Data Center Bridging (Dcb)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Data Center Bridging (DCB)
Page 520: Pfc Commands
— applies the input policy with the PFC configuration to an Commands ingress interface. PFC Commands The following PFC commands are supported on the S4810 platform. clear pfc counters Clear the PFC TLV counters and PFC statistics on an interface or stack unit. S4810...
Page 521: Dcb-Input
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version Introduced on the MXL 10/40GbE Switch IO Module.
Page 522: Dcb-Policy Input
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 523: Dcb-Policy Input Stack-Unit Stack-Ports All
Introduced on the MXL 10/40GbE Switch IO Module. 8.3.16.0 Usage NOTE: Please note that Dell Networking does not recommended to use this Information command as it has been deprecated in the current 9.4.(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future.
Page 524: Dcb Stack-Unit Pfc-Buffering Pfc-Port-Count Pfc-Queues
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 525 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 526: Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 527: Pfc Mode On
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 528: Pfc No-Drop Queues
Introduced on the MXL 10/40GbE Switch IO Module. 8.3.16.0 Usage NOTE: Please note that Dell Networking does not recommended to use this Information command as it has been deprecated in the current 9.4.(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future.
Page 529: Pfc Priority
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 530: Show Dcb
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 531: Show Interface Pfc
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 532 Down status messages added. (0.0) Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version Introduced on the MXL 10/40GbE Switch IO Module. 8.3.16.0 Usage To clear the PFC TLV counters, use the clear pfc counters interface Information port-type slot/port command.
Page 533 Pause Tx pkts PFC TLV Statistics: Number of PFC pause frames received. Pause Rx pkts Example Dell# show interfaces tengigabitethernet 0/49 pfc summary (Summary) Interface TenGigabitEthernet 0/49 Admin mode is on Admin is enabled Remote is enabled, Priority list is 4...
Page 534: Show Interface Pfc Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 535: Show Qos Dcb-Input
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 536: Show Stack-Unit Stack-Ports Pfc Details
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 537: Ets Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 538: Clear Ets Counters
Enter the keywords port-type then the slot/port information. Defaults none Command EXEC Privilege Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. Data Center Bridging (DCB)
Page 539: Dcb-Enable
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version Introduced on the MXL 10/40GbE Switch IO Module.
Page 540: Dcb-Output
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 541: Dcb-Policy Output
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 542: Dcb-Policy Output Stack-Unit Stack-Ports All
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 543: Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 544: Priority-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 545: Priority-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 546: Priority-Group Qos-Policy
Introduced on the MXL 10/40GbE Switch IO Module. 8.3.16.0 Usage NOTE: Please note that Dell Networking does not recommended to use this Information command as it has been deprecated in the current 9.4.(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future.
Page 547: Qos-Policy-Output Ets
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 548 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 549: Scheduler
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 550: Set-Pgid
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 551 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 552 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts Dell(conf-qos-policy-out-ets)#do sho int te 0/3 ets de Interface TenGigabitEthernet 0/3 Max Supported TC Groups is 4 Number of Traffic Classes is 8...
Page 553 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts Dell(conf)# show interfaces tengigabitethernet 0/0 ets detail Interface TenGigabitEthernet 0/0 Max Supported TC Groups is 4 Number of Traffic Classes is 8...
Page 554 Pkts, 0 Error Traffic Class Pkts Example Dell(conf)# show interfaces tengigabitethernet 0/0 ets detail (Detail) Interface TenGigabitEthernet 0/0 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : ------------------ Admin is enabled...
Page 555: Show Qos Dcb-Output
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 556: Show Stack-Unit Stack-Ports Ets Details
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 557: Dcbx Commands
TC-grp Priority# Bandwidth TSA ------------------------------------------------ 0,1,2,3,4,5,6,7 100% DCBX Commands The following DCBX commands are supported on the S4810 platform. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements. S4810 Syntax advertise dcbx-app-tlv iscsi To disable DCBX iSCSI TLV advertisements, use the no advertise dcbx-app- tlv iscsi command.
Page 558: Advertise Dcbx-Appln-Tlv
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 559: Advertise Dcbx-Tlv
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 560: Dcbx Port-Role
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Data Center Bridging (DCB)
Page 561: Dcbx Version
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 562: Debug Dcbx
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Data Center Bridging (DCB)
Page 563: Fcoe Priority-Bits
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 564: Iscsi Priority-Bits
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 565 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 566 Total DCBX Frame Number of DCBX frames with errors received. errors Total DCBX Number of unrecognizable DCBX frames received. Frames unrecognized Example Dell(conf)# show interface tengigabitethernet 0/49 dcbx detail Dell#show interface te 0/49 dcbx detail Data Center Bridging (DCB)
Page 567: Configuring Dcb Maps And Its Attributes
This topic contains the following sections that describe how to configure a DCB map, apply the configured DCB map to a port, configure PFC without a DCB map, and configure lossless queues. This functionality is supported on the S4810 platform. DCB Map: Configuration Procedure A DCB map consists of PFC and ETS parameters.
Page 568 Step Task Command Command Mode Enter global configuration mode to create a CONFIGURATION dcb-map name DCB map or edit PFC and ETS settings. Configure the PFC setting (on or off) and the DCB MAP priority-group ETS bandwidth percentage allocated to traffic group_num {bandwidth in each priority group, or whether the priority percentage | strict-...
Page 569 INTERFACE dcb-map name configure it with the PFC and ETS settings in the map; for example: Dell# interface tengigabitEthernet 0/0 Dell(config-if-te-0/0)# dcb-map SAN_A_dcb_map1 Repeat Steps 1 and 2 to apply a DCB map to more than one port. You cannot apply a DCB map on an interface...
Page 570 Step Task Command Command Mode fortygigabitEthernet slot/port} Enable PFC on specified priorities. Range: INTERFACE pfc priority 0-7. Default: None. priority-range Maximum number of lossless queues supported on an Ethernet port: 2. Separate priority values with a comma. Specify a priority range with a dash, for example: pfc priority 3,5-7 You cannot configure PFC using the pfc priority command on an...
Page 571: Data Center Bridging: Default Configuration
Queue : 2 Dell(conf)# NOTE: In Egress queue assignment (8 queues in S6000, 4 against in S5000 / S4810. PFC is not applied on specific dot1p priorities. ETS: Equal bandwidth is assigned to each port queue and each dot1p priority in a priority group.
Page 572: Dcb-Map
CONFIGURATION Modes INTERFACE Command Version 9.3(0.0) Introduced on the S4810 and S6000 platforms. History Usage A DCB map is a template used to configure DCB parameters and apply them on Information converged Ethernet interfaces. DCB parameters include priority-based flow control (PFC) and enhanced traffic selection (ETS).
Page 573 Command DCB MAP Modes Command Version 9.3(0.0) Introduced on the S4810, S6000 platforms. History Usage PFC and ETS settings are not pre-configured on Ethernet ports. You must use the Information dcb-map command to configure different groups of 802.1p priorities with PFC and ETS settings.
Page 574: Pfc Mode On
You cannot enable PFC and link-level flow control at the same time on an interface. NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future.
Page 575 None Command DCB MAP Modes Command Version 9.3(0.0) Introduced on the S4810, S6000 platforms. History Usage Use the dcb-map command to configure priority groups with PFC and/or ETS Information settings and apply them to Ethernet interfaces. Use the priority-pgid command to map 802.1p priorities to a priority group.
Page 576: Dcb-Map Stack-Unit All Stack-Ports All
Defaults None Command CONFIGURATION Modes Command Version 9.3(0.0) Introduced on the S4810 and S6000 platforms. History Usage The dcb-map stack-unit all stack-ports all command overwrites any Information previous DCB maps applied to stack ports. show qos dcb-map Display the DCB parameters configured in a specified DCB map.
Page 577: Applying A Dcb Map In A Switch Stack
Enhanced Transmission Selection (ETS). Percentage of bandwidth allocated to the priority group. PFC setting for the priority group: On (enabled) or Off. Priorities 802.1p priorities configured in the priority group. Example Dell# show qos dcb-map dcbmap2 State :Complete PfcMode:ON -------------------- PG:0 TSA:ETS...
Page 578: Dcb Pfc-Shared-Buffer-Size
Command CONFIGURATION mode Modes Command Version 9.3(0.0) Introduced on the S4810, S4820T, and S6000 platforms. History Usage Configure the maximum shared buffer available for PFC traffic. You can choose to Information increase or decrease the shared buffer that is currently allocated in the system by default.
Page 579: Dcb-Buffer-Threshold
Configure the profile name for the DCB buffer threshold. This utility is supported on the S4810, S4820T, and S6000 platforms. S4810 Syntax dcb buffer—threshold profile-name Parameters profile-name Enter the name of the profile, which can be a string of up to 32 characters in length.
Page 580: Qos-Policy-Buffer
Command DCB-BUFFER-THRESHOLD mode Modes Command Version 9.3(0.0) Introduced on the S4810, S4820T, and S6000 platforms. History Usage For each priority, you can specify the shared buffer threshold limit, the ingress Information buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets.
Page 581 Parameters policy-name Name of the QoS policy buffer that is applied to an interface for this setting to be effective in conjunction with the DCB input policy. You can specify the shared buffer threshold limit, the ingress buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets.
Page 582: Dcb-Policy Buffer-Threshold (Interface Configuration)
128000 pause-threshold 103360 resume-threshold 83520 dcb-policy buffer-threshold (Interface Configuration) Assign the DCB policy to the DCB buffer threshold profile on interfaces. This setting takes precedence over the global buffer-threshold setting. This utility is supported on the S4810 platform. Syntax dcb-policy buffer-threshold profile-name Parameters...
Page 583: Dcb-Policy Dcb-Buffer-Threshold (Global Configuration)
Assign the DCB policy to the DCB buffer threshold profile on stack ports that applies globally throughout the system. This utility is supported on the S4810 and platforms. This command is not supported on the S6000 platform because it does not contain stack ports.
Page 584: Show Qos Dcb-Buffer-Threshold
This method of configuration enables you to effectively manage and administer the behavior of lossless queues. Example Dell(conf)# dcb-policy buffer-threshold stack-unit all stack- ports all test show qos dcb-buffer-threshold Displays the DCB buffer threshold assigned to a QoS policy. This command is supported on the platform.
Page 585: Show Hardware Stack-Unit Buffer-Stats-Snapshot (With Polling And History)
show hardware stack-unit buffer-stats-snapshot (With Polling and History) View the buffer statistics tracking resource information with polling details and historical snapshots. This command is supported on the platform. Syntax show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource X history Y Parameters stack-unit Unique ID of the stack unit to select a particular stack...
Page 586 ID of 6, the aforementioned error is shown. Example Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 5 queue all history summary Stack-unit 0 unit 0 port 5 (interface te 0/4) ---------------------------------------------------------------...
Page 587 Instance 1 Instance 2 --------------------------------------------------------------- ------------------------------------------------ UCAST UCAST UCAST MCAST Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 5 prio-group all history summary Stack-unit 0 unit 0 port 5 (interface te 0/4) --------------------------------------------------------------- ------------------------------------------------ Instance 1 Instance 2 Instance 3...
Page 588 --------------------------------------- SHARED CELLS HEADROOM CELLS --------------------------------------- --------------------------------------- Q# TYPE TOTAL BUFFERED CELLS --------------------------------------- UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST Stack-unit: 0 unit: 0 port: 5 (interface Fo 0/4) --------------------------------------- SHARED CELLS HEADROOM CELLS...
Page 589 To determine the port that is congested and monitor all queues (including multicast and unicast queues] only on that port: Dell#$show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 queue all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0)
Page 590 MCAST Dell# To examine the port that is congested and monitor all multicast queues on that port: Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 queue mcast all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0) ---------------------------------------...
Page 591: Dcb Pfc-Total-Buffer-Size
To identify the port that is congested and monitor all the priority groups on that particular port: Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 prio all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0) --------------------------------------- SHARED CELLS...
Page 592: Show Running-Config Dcb-Buffer-Threshold
Example Dell(conf)#dcb pfc-total-buffer-size 5000 Dell(conf)#dcb pfc-total-buffer-size 4000 %ERROR: Total pfc buffer size configured cannot accommodate existing buffer requirement in the system. show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration.
Page 593 --------------------------------------------------------------- ------------------------------ Denotes dynamic buffering is enabled in respective queues On interface in which PFC is not enabled: Dell#show interface tengigabitethernet 0/20 pfc buffer- threshold The following table describes the output fields displayed for the show interface pfc buffer-threshold command:...
Page 594: Dcb Pfc-Queues
Enter the number of PFC queues in the range of 0 through 4. The number of ports supported based on lossless queues configured will depend on the buffer. Default The default number of PFC queues in the system is 2 for S4810 and 1 for S6000 platforms. Command CONFIGURATION mode...
Page 595: Debugging And Diagnostics
The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
Page 596 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 597: Offline Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 598: Online Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 599: Buffer Tuning Commands
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Changed the default value from global 4q to Dynamic.
Page 600: Hardware Commands
Similarly, when you configure buffer- profile global, you cannot not apply buffer-profile on any interface. If the default buffer-profile is active, Dell Networking OS displays an error message instructing you to remove the default configuration using the no buffer- profile global command.
Page 601: Clear Hardware System-Flow
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 602: Hardware Watchdog
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 603: Show Hardware Layer3
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 604: Show Hardware Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 605 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Modified the drops keyword range, unit keyword range and added the buffer and cpu management statistics options.
Page 606 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Example (Data- Dell#show hardware stack-unit 0 cpu data-plane statistics Plane) Input Statistics: 1856 packets, 338262 bytes 141 64-byte pkts, 1248 over 64-byte pkts, 11 over 127-byte pkts...
Page 607 Example (Drops Dell#show hardware stack-unit 0 drops unit 1 port 27 Unit, Port) --- Ingress Drops --- Ingress Drops IBP CBP Full Drops PortSTPnotFwd Drops IPv4 L3 Discards Policy Discards Packets dropped by FP (L2+L3) Drops Port bitmap zero Drops...
Page 608 10G FD Forward None XGMII 16360 Dell# Example Dell#show hardware stack-unit 0 unit 1 register (Register) 0x0068003c AGINGCTRMEMDEBUG.mmu0 = 0x00000000 0x0068003d AGINGEXPMEMDEBUG.mmu0 = 0x00000000 0x00680017 ASFCONFIG.mmu0 = 0x0000000e 0x0060004c ASFPORTSPEED.ge0 = 0x00000000 0x0060104c ASFPORTSPEED.ge1 = 0x00000000 0x0060204c ASFPORTSPEED.ge2 = 0x00000000 0x0060304c ASFPORTSPEED.ge3 = 0x00000000...
Page 609 0x0e719102 BCAST_BLOCK_MASK.hg1 = 0x00000000 0x0e71a102 BCAST_BLOCK_MASK.hg2 = 0x00000000 0x0e71b102 BCAST_BLOCK_MASK.hg3 = 0x00000000 0x0e71c102 BCAST_BLOCK_MASK.cpu0 = 0x00000000 0x0b700001 BCAST_STORM_CONTROL.ge0 = 0x00000000 0x0b701001 BCAST_STORM_CONTROL.ge1 = 0x00000000 0x0b702001 BCAST_STORM_CONTROL.ge2 = 0x00000000 0x0b703001 BCAST_STORM_CONTROL.ge3 = 0x00000000 0x0b704001 BCAST_STORM_CONTROL.ge4 = 0x00000000 0x0b705001 BCAST_STORM_CONTROL.ge5 = 0x00000000 0x0b706001 BCAST_STORM_CONTROL.ge6 = 0x00000000 0x0b707001 BCAST_STORM_CONTROL.ge7 = 0x00000000 0x0b708001 BCAST_STORM_CONTROL.ge8 = 0x00000000...
Page 610: Show Hardware System-Flow
Maximum Shared Limit for the Port: 30720 Default Packet Buffer allocate for the Port: 120 Used Packet Buffer for the Port: 0 Example Dell(conf)#sh hardware stack-unit 0 buffer unit 0 port 1 queue (Queue2/ 2 buffer-info Buffer-Info) ----- Buffer Stats for Unit 0 Port 1 Queue 2 -----...
Page 611 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 612 L2DLF Packets L2UCAST Packets L2BCASTPackets Dell# Example param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=1, mode=0x01, entries=1} ############## FP Entry for redirecting LACP traffic to CPU Port ############ EID 2045: gid=1, slice=15, slice_idx=0x02, prio=0x7fd, flags=0x82, Installed...
Page 613 action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, !--------- output truncated -----------------! Debugging and Diagnostics...
Page 615: Dynamic Host Configuration Protocol (Dhcp)
Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine. The Dell Networking operating system supports the basic DHCP commands on the S4810 platform. This chapter contains the following sections: •...
Page 616: Debug Ip Dhcp Server
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 617: Default-Router
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 618: Dns-Server
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 619: Excluded-Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 620: Hardware-Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 621: Lease
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 622: Netbios-Name-Server
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 623: Network
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 624: Pool
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 625: Show Ip Dhcp Configuration
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 626: Show Ip Dhcp Server
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 627: Arp Inspection-Trust
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 628: Clear Ip Dhcp Snooping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 629: Ip Dhcp Snooping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000.
Page 630: Ip Dhcp Snooping Binding
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 631: Ip Dhcp Snooping Database
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 632: Ip Dhcp Snooping Database Renew
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 633: Ip Dhcp Source-Address-Validation
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 634: Ip Dhcp Relay Information-Option
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 635: Ip Dhcp Snooping Verify Mac-Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 636: Show Ip Dhcp Snooping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Introduced on the S-Series and Z-Series.
Page 637: Commands To Configure Dns
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Introduced on the S-Series and Z-Series.
Page 638: Ip Domain-Name
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Introduced on the S-Series and Z-Series.
Page 639: Ip Host
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Introduced on the S-Series and Z-Series.
Page 640: Clear Host
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Introduced on the S-Series and Z-Series.
Page 641: Equal Cost Multi-Path (Ecmp)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Equal Cost Multi-Path (ECMP)
Page 642: Hash-Algorithm
Introduced on the Z9000. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.10.0 Usage Using CONFIGURATION mode, create an ECMP group ID. You can then assign Information interfaces to the ECMP group using CONFIGURATION ECMP-GROUP mode. You can also enable on the port-channel configuration using the CONFIGURATION ECMP-GROUP command mode.
Page 643 ecmp crc16 | TeraScale and ExaScale Only: Enter the keyword ecmp then crc16cc | one of the following options: crc32MSB | • crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync crc32LSB | crc- polynomial (default) upper | dest-ip • crc16cc: Use CRC16_CCITT — 16 bit CRC16 using | lsb | xor1 | CRC16-CCITT polynomial xor2 | xor4 |...
Page 644 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 645 (Single Linecard). • When hashing is done only on IPSA or IPDA, Dell Networking OS maintains bi- directionality with masks set to XX 00 for stack-unit 1 and 00 XX for stack-unit 2 (ip-sa-mask and ip-da-mask). The mask value must be the same for both stack-units when using multiple stack-units as ingress (where XX is any value from 00 to FF for both stack-units).
Page 646: Hash-Algorithm Ecmp
This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 647: Hash-Algorithm Seed
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 648: Ip Ecmp-Group
Introduced on the S6000. History Version 9.0.0.0 Introduced on the Z9000. Version Introduced on the S4810. 8.3.10.0 Usage You must save the new ECMP settings to the startup-config (write-mem) then Information reload the system for the new settings to take effect.
Page 649: Link-Bundle-Monitor Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 650: Show Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 651: Show Link-Bundle Distribution
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 653: Fips Cryptography
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1(0.0) Introduced on the Z9000.
Page 654: Show Fips Status
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1(0.0) Introduced on the Z9000.
Page 655: Ssh
Version Introduced on the S4820T. 8.3.19.0 Version Introduced on S4810. 8.3.12.0 Example Dell #show ip ssh SSH server : enabled. SSH server version : v1 and v2. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Encryption...
Page 656 -c encryption Enter the following encryption cipher to use. (For v2 clients cipher only.) Without the FIPS mode enabled: • 3des-cbc: Force ssh to use 3des-cbc encryption cipher. With the FIPS mode enabled: • aes128–cbc: Force ssh to use the aes128–cbc encryption cipher.
Page 657 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1(0.0) Introduced on the Z9000.
Page 658 Force ssh to use aes256-cbc encryption cipher Dell#ssh 10.11.8.12 -m ? hmac-sha1 Force ssh to use hmac-sha1 HMAC algorithm hmac-sha1-96 Force ssh to use hmac-sha1-96 HMAC algorithm FIPS Cryptography...
Page 659: Fcoe Transit
FCoE Transit To enable the FCoE Transit feature and configure FIP snooping, use the following Dell Networking Operating System commands on the S4810 platform. In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs).
Page 660: Clear Fip-Snooping Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 661: Debug Fip Snooping Rx
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Added the tx parameter.
Page 662: Feature Fip-Snooping
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the S4810 and S4820T. Added the receive parameters packet-type and interfaces and their options.
Page 663: Fip-Snooping Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 664: Fip-Snooping Max-Sessions-Per-Enodemac
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 665: Fip-Snooping Port-Mode Fcf
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 666: Show Fip-Snooping Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 667: Show Fip-Snooping Enode
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 668: Show Fip-Snooping Fcf
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 669: Show Fip-Snooping Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 670 Field Description Number of Number of FIP-snoop multicast discovery solicit frames Multicast received on the interface. Discovery Solicits Number of Number of FIP-snoop unicast discovery solicit frames Unicast Discovery received on the interface. Solicits Number of FLOGI Number of FIP-snoop FLOGI request frames received on the interface.
Page 671 Session failures that occurred on the interface. due to Hardware Config Example Dell# show fip-snooping statistics interface vlan 100 Number of Vlan Requests Number of Vlan Notifications Number of Multicast Discovery Solicits :2 Number of Unicast Discovery Solicits Number of FLOGI...
Page 672: Show Fip-Snooping System
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 673: Show Fip-Snooping Vlan
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 674 Version Introduced on the S4810. 8.3.12.0 FCoE Transit...
Page 675: Force10 Resilient Ring Protocol (Frrp)
• FRRP is media- and speed-independent. • FRRP is a Dell Networking proprietary protocol that does not interoperate with any other vendor. • Spanning Tree must be disabled on both primary and secondary interfaces before Resilient Ring protocol is enabled.
Page 676: Debug Frrp
Introduced. Usage Executing this command without the optional ring-id command clears the Information statistics counters on all the available rings. Dell Networking OS requires a command line confirmation before the command executes. This command clears the following counters: • hello Rx and Tx counters •...
Page 677: Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 678: Disable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 679: Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Force10 Resilient Ring Protocol (FRRP)
Page 680: Member-Vlan
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 681: Mode
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 682: Protocol Frrp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 683 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 684: Timer
Ring Master's MAC Address is 00:01:e8:13:a3:19 Topology Change Statistics: Tx:110 Rx:45 Hello Statistics: Tx:13028 Rx:12348 Number of state Changes: 34 Member Vlans: 1000-1009 Dell# Example (2 Dell#show frrp 2 summary Summary) Dell#show frrp 2 summary Ring-ID State Mode Ctrl_Vlan Member_Vlans ----------------------------------------------- Master 2...
Page 685 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 687: Garp Vlan Registration (Gvrp)
GARP VLAN Registration (GVRP) The Dell Networking operating system supports the basic GVRP commands on the S4810 platform. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
Page 688: Clear Gvrp Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 689: Debug Gvrp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 690: Disable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 691 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 692: Gvrp Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 693: Protocol Gvrp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 694: Show Config
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0...
Page 695: Show Garp Timers
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 696 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 697: Show Gvrp Statistics
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 698 • An entry for a new GVRP VLAN could not be created in the GVRP database. Example Dell#show gvrp statistics int gi 1/0 Join Empty Received: 0 Join In Received: 0 Empty Received: 0 LeaveIn Received: 0 Leave Empty Received: 0...
Page 699: High Availability (Ha)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 700: Process Restartable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 701: Redundancy Auto-Failover-Limit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 702: Redundancy Disable-Auto-Reboot
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 703: Redundancy Force-Failover
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 704: Redundancy Primary
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 705: Redundancy Reset-Counter
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 706: Redundancy Sfm Standby
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 707: Redundancy Synchronize
-- Switch Fabric Modules -- Slot Status -------------------------------------- active active Dell#configure Dell(conf)#redundancy sfm standby Taking secondary SFM offline... Dell(conf)#do show sfm all Switch Fabric State: up -- Switch Fabric Modules -- Slot Status ----------------------------------------- active standby Dell(conf)#no redundancy sfm Taking secondary SFM online...
Page 708: Show Patch
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 709: Show Processes Restartable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 710 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 711 Runtime Event Log is the contents of the Event log. • Running Config is the current running-config. This field only appears when you enter the command from the Primary RPM. Example Dell#show redundancy -- RPM Status -- ------------------------------------------------ RPM Slot ID: RPM Redundancy Role: Primary RPM State:...
Page 712 Line Card Config: succeeded Jul 13 2007 21:28:53 Start-up Config: succeeded Jul 13 2007 21:28:53 SFM Config State: succeeded Jul 13 2007 21:28:53 Runtime Event Log: succeeded Jul 13 2007 21:28:53 Running Config: succeeded Jul 13 2007 21:28:53 Dell# High Availability (HA)
Page 713: Icmp Message Types
ICMP Message Types This chapter lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping.
Page 714 Symbol Type Code Description Query Error redirect for network redirect for host redirect for type-of-service and network redirect for type-of-service and host echo request router advertisement router solicitation & time exceeded: time-to-live equals 0 during transit time-to-live equals 0 during reassembly parameter problem: IP header bad (catchall error)
Page 715: Internet Group Management Protocol (Igmp)
Internet Group Management Protocol (IGMP) The IGMP commands are supported by the Dell Networking operating software on the S4810 platform. This chapter contains the following sections: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376.
Page 716: Debug Ip Igmp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 717: Ip Igmp Access-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 718: Ip Igmp Group-Join-Limit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 719: Ip Igmp Immediate-Leave
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 720: Ip Igmp Last-Member-Query-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 721: Ip Igmp Querier-Timeout
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 722: Ip Igmp Query-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 723: Ip Igmp Query-Max-Resp-Time
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 724: Ip Igmp Ssm-Map
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 725: Ip Igmp Static-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 726: Ip Igmp Version
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 727: Show Ip Igmp Groups
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 728 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series and C-Series. Version 7.5.1.0 Expanded to support the detail option. E-Series legacy command. Usage This command displays the IGMP database, including configured entries for either...
Page 729: Show Ip Igmp Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 730: Show Ip Igmp Ssm-Map
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Internet Group Management Protocol (IGMP)
Page 731: Igmp Snooping Commands
Commands to (S,G) memberships. IGMP Snooping Commands Dell Networking OS supports IGMP Snooping version 2 and 3 on all Dell Networking systems. Important Points to Remember for IGMP Snooping • Dell Networking OS supports version 1, version 2, and version 3 hosts.
Page 732: Ip Igmp Snooping Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 733: Ip Igmp Snooping Fast-Leave
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 734: Ip Igmp Snooping Last-Member-Query-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 735: Ip Igmp Snooping Mrouter
Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage...
Page 736: Ip Igmp Snooping Querier
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.
Page 737: Show Ip Igmp Snooping Mrouter
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 738 If the port channel is a VLT port channel, an asterisk (*) after the port channel Information number (Po 100*) indicates the port channel is locally down and that a remote VLT port is up. Example Dell#show ip igmp snooping mrouter Interface Router Ports Vlan 2 Gi 13/3, Po 1 Dell# Related •...
Page 739: Interfaces
Interfaces The commands in this chapter are supported by Dell Networking operating software on the S4810 platform. This chapter contains the following sections: • Basic Interface Commands • Port Channel Commands • Time Domain Reflectometer (TDR) • UDP Broadcast Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
Page 740 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 741: Clear Dampening
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 742: Dampening
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 743: Description
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 744: Duplex (10/100 Interfaces)
Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Interfaces...
Page 745: Flowcontrol
This command applies to any physical interface with speed set to 10/100. Information NOTE: Starting with Dell Networking OS version 7.8.1.0, when you use a copper SFP2 module with catalog number GP-SFP2-1T in the S25P model of the S-Series, you can manually set its speed with the speed command. When you set the speed to 10 Mbps or 100 Mbps, you can also execute the duplex command.
Page 746 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 747 Can’t configure speed <1G when Asymmetric flowcontrol is on, config ignored • Dell Networking OS only supports rx on tx on and rx off tx off for speeds less than 1 Gig (Symmetric). NOTE: If you use the disable rx flow control command, Dell Networking recommends rebooting the system.
Page 748: Interface
Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Interfaces...
Page 749 Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series.
Page 750: Interface Group
For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command CONFIGURATION Modes Command Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL History Switch. Interfaces...
Page 751: Interface Loopback
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 752: Interface Managementethernet
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 753: Interface Null
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 754: Interface Range
Usage You cannot delete the Null interface. The only configuration command possible in Information a Null interface is ip unreachables. Example Dell(conf)#interface null 0 Dell(conf-if-nu-0)# Related interface — configures a physical interface. Commands interface loopback — configures a Loopback interface.
Page 755 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 756 Example Dell(conf)#interface range gi 2/0 - 23, gi 2/1 - 10 (Multiple Ports) Dell(conf-if-range-gi-2/0-23# Example Dell(conf)#interface range gi 2/1 - 11, gi 2/1 - 23 (Overlapping Dell(conf-if-range-gi-2/1-23# Ports) Usage Only VLAN and port-channel interfaces created using the interface vlan and...
Page 757: Interface Range Macro (Define)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 758: Interface Range Macro Name
Parameters name Enter the name of an existing macro. Defaults none Command CONFIGURATION Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. Interfaces...
Page 759: Interface Vlan
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
Page 760 Version 9.0.2.0 Introduced on the S6000. Version 9.1. Introduced on the S4810; added support for OpenFlow. (0.0) Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Usage For more information about VLANs and the commands to configure them, refer to...
Page 761: Intf-Type Cr4 Autoneg
Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.16.1 Introduced on the MXL 10/40GbE Switch IO Module. Usage If you configure interface type as CR4 with auto-negotiation enabled, also Information configure CR4 with auto-negotiation.
Page 762: Negotiation Auto
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 763 Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version Introduced on the E-Series.
Page 764 Force port to master mode forced-slave Force port to slave mode Dell(conf-if-autoneg)# Example Dell#show interfaces configured (Configured) GigabitEthernet 13/18 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:05:f7:fc Current address is 00:01:e8:05:f7:fc Interface index is 474791997 Internet address is 1.1.1.1/24...
Page 765: Monitor Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 766 pre-Version Introduced on the E-Series. 6.2.1.0 Usage In the Example, the delta column displays changes since the last screen refresh. Information The following are the monitor command menu options. Description systest-3 Displays the host name assigned to the system. monitor time Displays the amount of time since the monitor interface command was entered.
Page 767: Mtu
S4810 Syntax mtu value To return to the default MTU value, use the no mtu command. Parameters value Enter a maximum frame size in bytes. The range is from 594 to 12000 for the S4810. The default is 1554. Interfaces...
Page 768 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 769: Portmode Hybrid
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 770 Example Dell(conf)#interface gi 7/0 Dell(conf-if-gi-7/0)#portmode hybrid Dell(conf-if-gi-7/0)#interface vlan 10 Dell(conf-if-vl-10)#untagged gi 7/0 Dell(conf-if-vl-10)#interface vlan 20 Dell(conf-if-vl-20)#tagged gi 7/0 Dell(conf-if-vl-20)# Example Dell(conf-if-vl-20)#do show interfaces switchport Name: GigabitEthernet 7/0 802.1QTagged: Hybrid Vlan membership: Vlan Vlan 20 Native VlanId: 10 Dell(conf-if-vl-20)# Example (Vlan)
Page 771: Rate-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 772: Show Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 773: Show Interfaces
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 774 Use the show interfaces command for details on a specific interface. Information On the S4810, the show interface output displays incorrect rate information details over time for link monitoring when the rate-interval is configured for 5 seconds. Dell Networking recommends using higher rate-intervals such as 15 to 299 seconds to minimize the errors seen.
Page 775 F10 ID is not present Dell Networking allows unsupported SFP and XFP transceivers to be used, but Dell Networking OS might not be able to retrieve some data about them. In that case, typically when the output of this field is “Pluggable media present, Media type is unknown”, the Medium and the...
Page 776 Line Description Queuing States the packet queuing strategy. FIFO means first in first strategy... out. Input Statistics: Displays all the input statistics including: • Number of packets and bytes into the interface • Number of packets with VLAN tagged headers •...
Page 777 RPMs are installed in your system, use the show redundancy command to display which RPM is the Primary RPM. On the S4810 you can configure two global IPv6 addresses. To view the addresses, use the show interface managementethernet command. If you try to configure a third IPv6 address, a message displays.
Page 778 Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec,0.00% of line-rate Time since last interface status change: 1w0d5h Dell# Example Dell#show interfaces managementethernet 0/0 (ManagementE ManagementEthernet 0/0 is up, line protocol is up thernet) Hardware is Force10Eth, address is 00:01:e8:0b:a9:4c...
Page 779 Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Example Dell#show interfaces vlan 6 (OpenFlow instance) Vlan 6 is down, line protocol is down Address is 00:01:e8:8a:e1:8c, Current address is...
Page 780: Show Interfaces Configured
– displays Layer 2 information about the interfaces. show inventory (S-Series and Z-Series) – displays the S-Series and Z-Series switch types, components (including media), Dell Networking OS version including hardware identification numbers, and configured protocols. show ip interface – displays Layer 3 information about the interfaces.
Page 781: Show Interfaces Dampening
Example Dell#show interfaces configured GigabitEthernet 13/18 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:05:f7:fc Current address is 00:01:e8:05:f7:fc Interface index is 474791997 Internet address is 1.1.1.1/24 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit, Mode full duplex, Master ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interfaces"...
Page 782: Show Interfaces Phy
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 783 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 784 • 4 - 140 meters Link Status: Up or Down Speed: • Auto • 1000MB • 100MB • 10MB Example Dell#show int gigabitethernet 1/0 phy Mode Control: SpeedSelection: AutoNeg: Loopback: False PowerDown: False Isolate: False DuplexMode: Full Mode Status: AutoNegComplete:...
Page 785: Show Interfaces Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 786: Show Interfaces Status
Commands output statistics. show interfaces — displays information on a specific physical interface or virtual interface. show interfaces status S4810 Syntax show interfaces [interface | linecard slot-number] status Parameters interface (OPTIONAL) Enter one of the following keywords and slot/ port or number information: •...
Page 787 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 788: Show Interfaces Switchport
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 789 (“False”), or hybrid (“Hybrid”), which supports both untagged and tagged VLANs by port 13/0. Vlan membership Lists the VLANs to which the interface is a member. Starting with Dell Networking OS version 7.6.1, this field can display native VLAN membership by port 13/0. Example Dell#show interfaces switchport Name: GigabitEthernet 13/0 802.1QTagged: Hybrid...
Page 790: Show Interfaces Transceiver
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on theS6000.
Page 791 Line Description Temp High Alarm Factory-defined setting, typically in Centigrade. Value differs threshold between SFPs and SFP+. Voltage High Displays the interface index number used by SNMP to Alarm threshold identify the interface. Bias High Alarm Factory-defined setting. Value can differ between SFP and threshold SFP+.
Page 792 Line Description Power Low Factory-defined setting. Value can differ between SFP and Warning threshold SFP+. Temperature Current temperature of the SFPs. If this temperature crosses Temp High alarm/warning thresholds, the temperature high alarm/warning flag is set to true. Voltage Current voltage of the SFPs. If this voltage crosses voltage high alarm/warning thresholds, the voltage high alarm/ warning flag is set to true.
Page 793 Rx Power Low This can be either true or false, depending on the Current Rx Warning Flag power value displayed above. Example Dell#show interfaces gigabitethernet 1/0 transceiver SFP is present. SFP 0 Serial Base ID fields Interfaces...
Page 794 SFP 0 Id = 0x03 SFP 0 Ext Id = 0x04 SFP 0 Connector = 0x07 SFP 0 Transciever Code = 0x00 0x00 0x00 0x01 0x20 0x40 0x0c 0x05 SFP 0 Encoding = 0x01 SFP 0 BR Nominal = 0x15 SFP 0 Length(9um) Km = 0x00 SFP 0 Length(9um) 100m...
Page 795: Show Range
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 796: Show Running-Config Ecmp-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 797 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 798: Speed (For 10/100/1000 Interfaces)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 799: Speed (Management Interface)
For speed settings of 1000 or auto, the software sets the link to auto-negotiation and you cannot change that setting. NOTE: Starting with Dell Networking OS version 7.8.1.0, when you use a copper SFP2 module with catalog number GP-SFP2-1T in the S25P model of the S-Series, you can manually set its speed with the speed command.
Page 800: Stack-Unit Portmode
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 801: Switchport
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 802 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 803: Egress Interface Selection (Eis) Commands
VLAN. To use the switchport backup interface command on a port, first enter the switchport command. For more information, refer to the “Configuring Redundant Links” section in the “Layer 2” chapter of the Dell Networking OS Configuration Guide. Related interface port-channel —...
Page 804: Application (For Http And Icmp)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. Introduced on the Z9000, S4810, and S4820T.
Page 805: Clear Management Application Pkt-Cntr
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. Introduced on the Z9000, S4810, and S4820T.
Page 806: Show Ip Management-Eis-Route
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 807: Show Management Application Pkt-Fallback-Cntr
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. Introduced on the Z9000, S4810, and S4820T.
Page 808: Port Channel Commands
A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell Networking OS, a LAG is referred to as a Port Channel.
Page 809 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 810: Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 811: Interface Port-Channel
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 812: Minimum-Links
A Port Channel can contain both 100/1000 interfaces and GE interfaces. Based on the first interface configured in the Port Channel and enabled, Dell Networking OS determines if the Port Channel uses 100 Mb/s or 1000 Mb/s as the common speed.
Page 813: Port-Channel Failover-Group
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 814: Show Config
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
Page 815: Show Interfaces Port-Channel
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 816 Usage The following describes the show interfaces port-channel command shown Information in the following example. Field Description Port-Channel 1... Displays the LAG’s status. In the Example, the status of the LAG’s LAG fate-sharing group (“Failover-group”) is listed. Hardware is... Displays the interface’s hardware information and its assigned MAC address.
Page 817 Example Dell#show interfaces port-channel 20 Port-channel 20 is up, line protocol is up (Failover-group 1 is down) Hardware address is 00:01:e8:01:46:fa Port-channel is part of failover-group 1 Internet address is 1.1.120.1/24 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 2000 Mbit...
Page 818: Show Port-Channel-Flow
Field Description • In Layer 3 port channels, the primary port is not indicated. Example Dell#sh int por 1 br LAG Mode Status Uptime Ports 00:00:08 Gi 3/0 (Up) * Gi 3/1 (Down) Gi 3/2 (Up) Dell# Related show lacp —...
Page 819 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 820: Time Domain Reflectometer (Tdr)
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 821: Show Tdr
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 822: Udp Broadcast
(not to exceed 200 pps) IP/UDP broadcast traffic arriving on a physical or VLAN interface. Important Points to Remember • This feature is available only on the S4810 platform. • Routing information protocol (RIP) is not supported with the UDP Broadcast feature.
Page 823: Debug Ip Udp-Helper
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 824: Ip Udp-Broadcast-Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 825 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 826: Show Ip Udp-Helper
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 827: Enhanced Validation Of Interface Ranges
Enhanced Validation of Interface Ranges This functionality is supported on the S4810 platform. You can avoid specifying spaces between the range of interfaces, separated by commas, that you configure by using the interface range command. For example, if you enter a list of interface ranges, such as interface range fo 2/0-1,te 10/0,gi 3/0,fa 0/0, this configuration is considered valid.
Page 829: Internet Protocol Security (Ipsec)
Due to performance limitations on the control processor, you cannot enable IPSec on all packets in a communication session. crypto ipsec transform-set Create a transform set, or combination of security algorithms and protocols, of cryptos. S4810 Syntax crypto ipsec transform-set name {ah-authentication {md5|sha1| null} | esp-authentication {md5|sha1|null} | esp-encryption...
Page 830 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 831: Crypto Ipsec Policy
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 832: Management Crypto-Policy
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 833: Session-Key
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 834: Show Crypto Ipsec Transform-Set
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 835: Show Crypto Ipsec Policy
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 836 Protocol type : tcp IP or IPv6 : IPv6 Source address : a::1 Source mask : /128 Source port : 21 Destination address : a::2 Destination mask : /128 Destination port source-interface name : source-interface num Dell# Internet Protocol Security (IPSec)
Page 837: Transform-Set
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
Page 839: Ipv4 Routing
IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the S4810 platform. To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). S4810 Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command.
Page 840: Arp Backoff-Time
8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
Page 841: Arp Learn-Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 842: Arp Max-Entries
At time t=1, Dell Networking OS receives an ARP request for IP A.B.C.D. At time t=2, Dell Networking OS installs an ARP entry for A.B.C.D only on RP2. Beginning with Dell Networking OS version 8.3.1.0, when a gratuitous ARP is received, Dell Networking OS installs an ARP entry on all three CPUs.
Page 843: Arp Retries
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 844: Clear Arp-Cache
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 845 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 846: Clear Host
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 847: Clear Ip Route
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version Introduced on the S4820T. 8.3.19.0 Usage To clear Layer 3 CAM inconsistencies, use this command.
Page 848: Clear Tcp Statistics
Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. IPv4 Routing...
Page 849: Debug Arp
Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version Introduced on the E-Series. 6.2.1.1 debug arp View information on ARP transactions.
Page 850: Debug Ip Dhcp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 851 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
Page 852: Debug Ip Icmp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 853: Debug Ip Packet
Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale.
Page 854 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 855 Field Description Lists the destination address of the packet and the name of the interface (in parentheses) through which the packet is being sent out on the network. Displays the packet’s length. sending, rcvd, The last part of each line lists the status of the packet. fragment, sending broad/multicast proto, unroutable...
Page 856: Ip Address
A message appears identifying the error (refer to the Example below). Example (Error Dell#debug ip packet access-group test Messages) %Error: port operator GT not supported in access-list debug %Error: port operator LT not supported in access-list debug...
Page 857: Ip Directed-Broadcast
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 858: Ip Domain-List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 859: Ip Domain-Lookup
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 860: Ip Domain-Name
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 861: Ip Helper-Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 862: Ip Helper-Address Hop-Count Disable
DHCP client. Dell Networking OS uses standard DHCP ports, that is UDP ports 67 (server) and 68 (client) for DHCP relay services. It listens on port 67 and if it receives a broadcast, the software converts it to unicast, and forwards to it to the DHCP-server with source port=68 and destination port=67.
Page 863: Ip Host
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 864: Ip Icmp Source-Interface
IPv4 packets. This functionality is supported on the S4810, , , and platforms. Syntax...
Page 865: Ipv6 Icmp Source-Interface
IPv6 packets. This functionality is supported on the S4810, , , and platforms. Syntax...
Page 866 Not configured. Command CONFIGURATION Modes Command Version 9.3(0.0) Introduced on the S4810, S4820T, S6000, and Z9000 History platforms. Usage You can enable the mechanism to configure the source or the originating interface Information from which the packet (the device that generates the ICMP error messages) is...
Page 867: Ip Max-Frag-Count
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 868: Ip Max-Routes
Set the IP MTU (frame size) of the packet the RPM transmits for the line card interface. If the packet must be fragmented, Dell Networking OS sets the size of the fragmented packets to the size specified in this command.
Page 869 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 870: Ip Name-Server
Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. IPv4 Routing...
Page 871: Ip Proxy-Arp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 872: Ip Route
— displays the interface routing status and configuration. Commands ip route Assign a static route to the switch. S4810 Syntax ip route [vrf vrf-name] ip-address mask {ip-address | interface [ip-address]} [distance] [permanent] [tag tag-value] [vrf vrf- name] To delete a specific static route, use the no ip route destination mask command.
Page 873 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 874: Ip Source-Route
— views the switch routing table. Commands ip source-route Enable Dell Networking OS to forward IP packets with source route information in the header. S4810 Syntax ip source-route To drop packets with source route information, use the no ip route-source command.
Page 875: Ip Unreachables
6.1.1.0 load-balance By default, for C-Series and S-Series, Dell Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
Page 876 Defaults IP 4-tuple (IP SA, IP DA, Source Port, Destination Port) Command CONFIGURATION Modes Command This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. IPv4 Routing...
Page 877: Load-Balance Hg
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version Added the ingress-port parameter for the S4810.
Page 878 Parameters {ip-selection| To use IPv4 key fields in hash computation, enter the ipv6-selection keyword ip-selection then one of the parameters. To use [source-ip | IPv6 key fields in hash computation, enter the keyword source-ipv6 | ipv6-selection then one of the parameters. source-port-id •...
Page 879: Management Route
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 880: Show Arp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 881 Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF. NOTE: Use this attribute to start a BGP instance for either a specific address family corresponding to the default VRF or an IPv4 address family corresponding to a non- default VRF.
Page 882 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF and added usage information for the (0.0)
Page 883 Description VLAN Displays the VLAN ID, if any, associated with the ARP entry. Lists which CPU the entries are stored on. Example Dell>show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU ------------------------------------------------------------- Internet 192.2.1.254 1 00:00:c0:02:01:02 Gi 9/13 Internet 192.2.1.253 1...
Page 884: Show Arp Retries
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 885 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 886: Show Ip Cam Linecard
For dynamically learned entries only. Type Displays IP as the type of entry. Address Displays the IP addresses assigned to the host. Example Dell#show hosts Default domain is not set Name/address lookup uses static mappings Name servers are not set Host Flags...
Page 887 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 888 0 port pipe 0. Initial Size Displays the CAM size Dell Networking OS allocates for the corresponding mask. Dell Networking OS adjusts the CAM size if the number of routes for the mask exceeds the initial allocation.
Page 889: Show Ip Cam Stack-Unit
{detail | member-info [detail [group-index index- number]]}| summary] Parameters Enter the stack-unit ID. The unit ID range is from 0 to 11 for the S4810. port-set pipe- Enter the keyword port-set then the number of the stack number unit’s port-pipe. The unit ID range is from 0 to 0 for the S4810.
Page 890 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 891 0 port pipe 0. Initial Size Displays the CAM size Dell Networking OS allocates for the corresponding mask. Dell Networking OS adjusts the CAM size if the number of routes for the mask exceeds the initial allocation.
Page 892: Show Ip Fib Linecard
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 893 Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version Introduced on the E-Series. 6.1.1.0 Usage The following describes the show ip fib command shown in the following Information example.
Page 894: Show Ip Fib Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 895: Show Ip Flow
Displays the MAC address. Port Displays the egress-port information. Displays the VLAN ID. If no VLAN is assigned, zero (0) is listed. Displays the number of ECMP paths. Example Dell#show ip fib stack-unit 0 Destination Gateway First-Hop Mac-Addr ------------------------------------------------------ 10.10.10.10/32 Direct, Nu 0 0.0.0.0...
Page 896 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 897: Show Ip Interface
Egress interface:Gi 1/14 to 1.7.1.2[CAM hit 103710] unfragmented packet Gi 1/10 to 1.2.1.2[CAM hit 103710] fragmented packet show ip interface View IP-related information on all interfaces. S4810 Syntax show ip interface [interface | brief] [configured] Parameters interface (OPTIONAL) Enter the following keywords and slot/port or number information: •...
Page 898 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 899 Example Dell#show ip int te 0/0 TenGigabitEthernet 0/0 is down, line protocol is down Internet address is not set IP MTU is 1500 bytes Inbound access list is not set Proxy ARP is enabled Split Horizon is enabled Poison Reverse is disabled...
Page 900: Show Ip Management-Route
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 901: Show Ipv6 Management-Route
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 902: Show Ip Protocols
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 903: Show Ip Route
View information, including how they were learned, about the IP routes on the switch. S4810 Syntax show ip route [vrf vrf-name] hostname | ip-address [mask] [longer-prefixes] | list prefix-list | protocol [process-id | routing-tag] | all | connected | static | summary]...
Page 904 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. Added support for VRF.
Page 905 Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured. Example Dell#show ip route all Codes:C- connected, S - static, R - RIP B- BGP, IN - internal BGP, EX - external BGP, LO - Locally Originated...
Page 906: Show Ip Route List
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 907: Show Ip Route Summary
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 908 Total 1388 Displays the number of active and non-active routes and active... the memory usage of those routes. If there are no routes configured in the Dell Networking OS, this line does not appear. Example Dell>show ip route summary Route Source...
Page 909: Show Ip Traffic
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 910 Definition unknown No receiver for these packets. Counts packets whose protocol... protocol type field is not recognized by Dell Networking OS. not a gateway... Packets can not be routed; the host/network is unreachable. security failures... Counts the number of received unicast/multicast packets that could not be forwarded due to: •...
Page 911: Show Tcp Statistics
1.3.6.1.4.1.6027.3.3.5.2.4 • ARP Statistics: Sent: Proxy: Object = f10ArpProxySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.5 Example Dell#show ip traffic Control Processor IP Traffic: IP statistics: Rcvd: 23857 total, 23829 local destination 0 format errors, 0 checksum errors, 0 bad hop count 0 unknown protocol, 0 not a gateway...
Page 912 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 913 Lists the number of keepalive packets in timeout, the number keepalive probes and the number of TCP connections dropped during keepalive. Example Dell#show tcp stat cp Control Processor TCP: Rcvd: 10585 Total, 0 no port 0 checksum error, 0 bad offset, 0 too short...
Page 914 14 Connections closed (including 0 dropped, 0 embryonic dropped) 20 Total rxmt timeout, 0 connections dropped in rxmt timeout 0 Keepalive timeout, 0 keepalive probe, 0 Connections dropped in keepalive Dell# Related show ip cam stack-unit — displays the CAM table. Commands...
Page 915: Ipv6 Access Control Lists (Ipv6 Acls)
IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking S4810 platform. NOTE: For IPv4 ACL commands, refer to the Access Control Lists (ACL) chapter. Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, refer to the cam-acl command.
Page 916: Show Cam-Acl
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 917 Version 8.4.2.1 Introduced on the S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.8.1.0 Introduced on the C-Series. Example Dell#show cam-acl -- Chassis Cam ACL -- Current Settings(in block sizes) L2Acl Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos -- Line card 4 --...
Page 918: Permit Icmp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 919: Permit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 920: Ipv6 Control-Plane Egress-Filter
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 921: Cam-Acl-Egress
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for CoPP for OSPFv3 on the S4810, S4820T, S6000, and Z9000 platforms.
Page 922 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 923: Cam-Acl
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 924 Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10). IPv6 Access Control Lists (IPv6 ACLs)
Page 925: Ipv6 Basics
IPv6 basic commands are supported on the Dell Networking S4810 platform. NOTE: For information about the Dell Networking operating software version and platform that supports IPv6 in each software feature, refer to the IPv6 Addressing chapter of the Dell Networking OS Configuration Guide.
Page 926: Clear Ipv6 Route
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 927: Ipv6 Address Autoconfig
The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version 8.3.11.1 Introduced on the Z9000. ipv6 address autoconfig Configure IPv6 address auto-configuration for the management interface.
Page 928: Ipv6 Address
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1(0.0) Updated Usage Information.
Page 929: Ipv6 Address Eui64
Example Dell(conf)#interface gigabitethernet 10/0 Dell(conf-if-gi-10/0)#ipv6 address ? X:X:X:X::X IPv6 address Dell(conf-if-gi-10/0)#ipv6 address 2002:1:2::3 ? <0-128> Prefix length in bits Dell(conf-if-gi-10/0)#ipv6 address 2002:1:2::3 /96 ? <cr> Dell(conf-if-gi-10/0)#ipv6 address 2002:1:2::3 /96 Dell(conf-if-gi-10/0)#show config interface GigabitEthernet 10/0 no ip address ipv6 address 2002:1:2::3 /96...
Page 930: Ipv6 Control-Plane Icmp Error-Rate-Limit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced.
Page 931: Ipv6 Flowlabel-Zero
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 932: Ipv6 Name-Server
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 933: Ipv6 Nd Dad Attempts
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 934: Ipv6 Nd Prefix
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. ipv6 nd prefix Specify which IPv6 prefixes are included in Neighbor Advertisements. S4810 Syntax ipv6 nd prefix {ipv6-prefix | prefix-length | default} [no- advertise] | [no-autoconfig] [no-rtr-address] [off-link]...
Page 935: Ipv6 Route
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 936 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 937: Ipv6 Unicast-Routing
When the interface goes down, Dell Networking OS withdraws the route. The route Information is re-installed, by Dell Networking OS, when the interface comes back up. When a recursive resolution is “broken,” Dell Networking OS withdraws the route. The route is re-installed, by Dell Networking OS, when the recursive resolution is satisfied.
Page 938: Show Ipv6 Cam Stack-Unit
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 939 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 940: Show Ipv6 Control-Plane Icmp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 941: Show Ipv6 Flowlabel-Zero
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 942: Show Ipv6 Interface
Display the status of interfaces configured for IPv6. S4810 Syntax show ipv6 interface interface [brief] [configured] [gigabitethernet slot | slot/port] [loopback interface-number] [managementethernet slot/port] [port-channel number] [stack- unit id] [tengigabitethernet slot | slot/port] [fortyGigE slot | slot/port] [tunnel tunnel-id] [vlan vlan-id]...
Page 943 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. Added support for tunnel interface.
Page 944 ND router advertisements are sent every 200 to 600 seconds ND router advertisements live for 1800 seconds Dell# Example Dell# (Managementet Dell#show ipv6 int man 0/0 ManagementEthernet 0/0 is up, line protocol is up hernet) IPV6 is enabled Link Local address: fe80::201:e8ff:fe8a:e8f7 Global Unicast address(es):...
Page 945: Show Ipv6 Mld_Host
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 946: Show Ipv6 Route
---- MLDv1 Queries ---- Errors: Malformed Packets: 4510 show ipv6 route Displays the IPv6 routes. S4810 Syntax show ipv6 route [ipv6-address prefix-length] [hostname] [all] [bgp as number] [connected] [isis tag] [list prefix-list name] [ospf process-id] [rip] [static] [summary] Parameters ipv6-address...
Page 947 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000.
Page 948 Dist/Metric Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured. Example (E- Dell#show ipv6 route Series) Codes:C-connected, L-local, S-static, R-RIP, B-BGP, IN-internal BGP, EX-external BGP, LO-Locally Originated, O-OSPF, IA-OSPF inter area, N1-OSPF NSSA external type 1,...
Page 949: Trust Ipv6-Diffserv
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 950 IPv6 Service Class Queue ID Field 101XXXXX 100XXXXX 011XXXXX 010XXXXX 001XXXXX 000XXXXX IPv6 Basics...
Page 951: Iscsi Optimization
Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on an S4810 system. To configure and verify the iSCSI optimization feature, use the following Dell Networking OS commands. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements.
Page 952: Iscsi Aging Time
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 953: Iscsi Enable
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 954: Iscsi Priority-Bits
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 955: Iscsi Profile-Compellant
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 956: Show Iscsi
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 957: Show Iscsi Session
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 958: Show Iscsi Session Detailed
Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version Introduced on MXL 10/40GbE Switch IO Module. 8.3.16.0 Example Dell# show isci session Session 0: ------------------------------------------------------ Target: iqn.2001-05.com.equallogic: 0-8a0906-0e70c2002-10a0018426a48c94-iom010 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg ISID: 400001370000 Session 1: --------------------------------------------------------- Target: iqn.2001-05.com.equallogic: 0-8a0906-0f60c2002-0360018428d48c94-iom011 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg...
Page 959 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 960: Show Run Iscsi
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Introduced on the S4820T.
Page 961: Intermediate System To Intermediate System (Is-Is)
(Level 1 and Level 1-2 devices). Only Level 1-2 and Level 2 devices communicate with other areas. IS-IS protocol standards are listed in the Standard Compliance chapter in the Dell Networking OS Configuration Guide. NOTE: The fundamental mechanisms of IS-IS are the same between IPv4 and IPv6. Where there are differences between the two versions, they are identified and clarified in this chapter.
Page 962: Advertise
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 963: Area-Password
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 964: Clear Config
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 965: Clear Isis
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 966: Clns Host
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 967: Debug Isis Adj-Packets
This guide is platform-specific. For command information about other platforms, History refer to the relevant FTOS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 968: Debug Isis Local-Updates
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000.
Page 969: Debug Isis Snp-Packets
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000.
Page 970: Debug Isis Spf-Triggers
The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version 6.3.1.0 Introduced.
Page 971: Debug Isis Update-Packets
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000.
Page 972: Default-Information Originate
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 973: Description
Modes Command Version 9.0.2.0 Introduced on the S6000. History Version Introduced on the S4820T. 8.3.19.0 Version Introduced on the S4810. 8.3.12.0 Version 8.3.11.1 Introduced on the Z9000. pre-7.7.1.0 Introduced. Related router isis — Enter ROUTER mode on the switch. Commands...
Page 974: Distance
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 975: Distribute-List In
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 976: Distribute-List Out
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 977: Distribute-List Redistributed-Override
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 978: Domain-Password
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 979: Graceful-Restart Ietf
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 980: Graceful-Restart Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 981: Graceful-Restart T1
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 982: Graceful-Restart T2
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 983: Graceful-Restart T3
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 984: Hello Padding
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 985: Hostname Dynamic
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 986: Ignore-Lsp-Errors
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 987: Ipv6 Router Isis
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 988: Isis Circuit-Type
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 989: Isis Csnp-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 990: Isis Hello-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 991: Isis Hello-Multiplier
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 992: Isis Hello Padding
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 993: Isis Ipv6 Metric
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 994: Isis Metric
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 995: Isis Network Point-To-Point
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 996 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 997: Isis Priority
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OSCommand Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 998: Is-Type
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 999: Log-Adjacency-Changes
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1000 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1001: Lsp-Mtu
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1002: Lsp-Refresh-Interval
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1003: Max-Area-Addresses
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1004: Maximum-Paths
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1005: Metric-Style
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1006: Multi-Topology
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1007: Net
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version Introduced on the S4810. 8.3.12.0 Version 7.8.1.0 Introduced.
Page 1008: Passive-Interface
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1009: Redistribute
Redistribute routes from one routing domain to another routing domain. S4810 Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] To end redistribution or disable any of the specified keywords, use the no...
Page 1010 This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
Page 1011: Redistribute Bgp
This guide is platform-specific. For command information about other platforms, History refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. 1011 Intermediate System to Intermediate System (IS-IS)
Page 1012: Redistribute Ospf
Introduced on the S6000. Version Introduced on the S4820T. 8.3.19.0 Version 8.3.11.1 Introduced on the Z9000. Version Introduced on the S4810. 8.3.12.0 Version 7.5.1.0 Added support for IPv6 ISIS. Version 6.3.1.0 Introduced. Usage BGP to IS-IS redistribution supports “match” options using route maps. You can set...

Dell S4810 Reference Manual

1 About this Guide

151 CLI Basics

3 File Management

4 Control and Monitoring

5 1Ag

6 1X

7 Access Control Lists (ACL)

8 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM)

9 Bidirectional Forwarding Detection (BFD)

10 Border Gateway Protocol

Quick Links

Related Manuals for Dell S4810

Summary of Contents for Dell S4810