Cisco TelePresence System Codec C40 Administrator's Manual page 72
Software version tc7.0
Hide thumbs
Also See for TelePresence System Codec C40:
- Reference manual (224 pages) ,
- Administrator's manual (143 pages) ,
- User manual (51 pages)
Table of Contents
Advertisement
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60
Contents
Conference [1..1] VideoBandwidth Mode
Set the conference video bandwidth mode.
Requires user role: ADMIN
Value space: <Dynamic/Static>
Dynamic: The available transmit bandwidth for the video channels are distributed among the
currently active channels. If there is no presentation, the main video channels will use the
bandwidth of the presentation channel.
Static: The available transmit bandwidth is assigned to each video channel, even if it is not
active.
Conference 1 VideoBandwidth Mode: Dynamic
Example:
Conference [1..1] VideoBandwidth MainChannel Weight
The available transmit video bandwidth is distributed on the main channel and presentation
channel according to "MainChannel Weight" and "PresentationChannel Weight". If the main
channel weight is 2 and the presentation channel weight is 1, then the main channel will use
twice as much bandwidth as the presentation channel.
Requires user role: ADMIN
Value space: <1..10>
Range: 1 to 10.
Conference 1 VideoBandwidth MainChannel Weight: 5
Example:
Conference [1..1] VideoBandwidth PresentationChannel Weight
The available transmit video bandwidth is distributed on the main channel and presentation
channel according to "MainChannel Weight" and "PresentationChannel Weight". If the main
channel weight is 2 and the presentation channel weight is 1, then the main channel will use
twice as much bandwidth as the presentation channel.
Requires user role: ADMIN
Value space: <1..10>
Range: 1 to 10.
Conference 1 VideoBandwidth PresentationChannel Weight: 5
Example:
D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.
Introduction
Web interface
System settings
System settings
Conference [1..1] Presentation Policy
Control how the presentation service is to be performed.
Requires user role: ADMIN
Value space: <LocalRemote/LocalOnly>
LocalRemote: The presentation will be shown locally and sent to remote side.
LocalOnly: The presentation will only be shown locally.
Conference 1 Presentation Policy: LocalRemote
Example:
Conference [1..1] Presentation RelayQuality
This configuration applies to video systems that are using the built-in MultiSite feature (optional)
to host a multipoint video conference. When a remote user shares a presentation, the video
system (codec) will transcode the presentation and send it to the other participants in the
multipoint conference. The RelayQuality setting specifies whether to give priority to high frame
rate or to high resolution for the presentation source.
Requires user role: ADMIN
Value space: <Motion/Sharpness>
Motion: Gives the highest possible frame rate. Used when there is a need for higher frame
rates, typically when there is a lot of motion in the picture.
Sharpness: Gives the highest possible resolution. Used when you want the highest quality of
detailed images and graphics.
Conference 1 Presentation RelayQuality: Sharpness
Example:
Conference [1..1] Presentation OnPlacedOnHold
Define whether or not to continue sharing a presentation after the remote site has put you on
hold.
Requires user role: ADMIN
Value space: <Stop/NoAction>
Stop: The video system stops the presentation sharing when the remote site puts you on
hold. The presentation will not continue when the call is resumed.
NoAction: The video system will not stop the presentation sharing when put on hold. The
presentation will not be shared while you are on hold, but it will continue automatically when
the call is resumed.
Conference 1 Presentation OnPlacedOnHold: NoAction
Example:
www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reserved.
72
Administrator Guide
Setting passwords
Appendices
Hide quick links:
Advertisement
Table of Contents
