Cisco TelePresence System Codec C40 Administrator's Manual page 67
Software version tc7.0
Hide thumbs
Also See for TelePresence System Codec C40:
- Reference manual (224 pages) ,
- Administrator's manual (143 pages) ,
- User manual (51 pages)
Table of Contents
Advertisement
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60
Contents
Cameras Camera [1..7] Gamma Mode
Applies to cameras which support gamma mode. Gamma describes the nonlinear relationship
between image pixels and monitor brightness. The Cisco TelePresence PrecisionHD 720p
camera supports gamma mode. The PrecisionHD 1080p camera does not support gamma
mode.
Requires user role: ADMIN
Value space: <Auto/Manual>
Auto: Auto is the default and the recommended setting.
Manual: In manual mode the gamma value is changed with the gamma level setting, ref:
Cameras Camera [1..n] Gamma Level.
Cameras Camera 1 Gamma Mode: Auto
Example:
Cameras Camera [1..7] Gamma Level
By setting the Gamma Level you can select which gamma correction table to use. This setting
may be useful in difficult lighting conditions, where changes to the brightness setting does not
provide satisfactory results. Requires the Gamma Mode to be set to Manual.
Requires user role: ADMIN
Value space: <0..7>
Range: Select a value from 0 to 7.
Cameras Camera 1 Gamma Level: 0
Example:
Cameras Camera [1..7] IrSensor
The IR sensor LED is located in the front of the camera and flickers when the IR sensor is
activated from the remote control. Both the Codec C Series and PrecisionHD camera have IR
sensors, and only one of them needs to be enabled at the time.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the IR sensor on the camera.
On: Enable the IR sensor on the camera.
Cameras Camera 1 IrSensor: On
Example:
D14636.13 Profile C60-C40 and Codec C60-C40 Administrator Guide TC7.0, DECEMBER 2013.
Introduction
Web interface
System settings
System settings
Cameras Camera [1..7] Mirror
With Mirror mode (horizontal flip) you can mirror the image on screen.
Requires user role: ADMIN
Value space: <Auto/Off/On>
Auto: When the camera is placed upside down the image is automatically mirrored. Use this
setting with cameras that can be mounted upside down, and that can auto detect that the
camera is mounted upside down.
Off: See the self-view in normal mode, that is the experience of self-view is as seeing
yourself as other people see you.
On: See the self-view in mirror mode, that is the self-view is reversed and the experience of
self-view is as seeing yourself in a mirror.
Cameras Camera 1 Mirror: Off
Example:
Cameras Camera [1..7] MotorMoveDetection
This setting applies only when using a Cisco TelePresence PrecisionHD 1080p12x camera.
If adjusting the camera position by hand you can configure whether the camera should keep its
new position or return to the preset or position it had before.
Requires user role: ADMIN
Value space: <Off/On>
Off: When the camera position is adjusted manually the camera will keep this position until
adjusted again. WARNING: If moving the camera by hand, the camera will not register the
new pan and tilt values since there is no position feedback. This will result in wrong pan and
tilt values when recalling the camera presets subsequently.
On: When the camera position is adjusted manually, or the camera detects that the motors
have moved, it will first re-initialize (i.e. go to default position) then return to the preset/
position it had before the camera was adjusted.
Cameras Camera 1 MotorMoveDetection: Off
Example:
www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reserved.
67
Administrator Guide
Setting passwords
Appendices
Hide quick links:
Advertisement
Table of Contents
