Chapter 9 Error Code List - Brother BES-116 Instruction Manual
Electronic embroidery machine
Hide thumbs
Also See for BES-116:
- Supplementary manual (5 pages) ,
- User manual (3 pages) ,
- Supplement manual (3 pages)
Table of Contents
Advertisement
Chapter 9 Error code list
Code
Error Messages
E-00
ERROR 00
E-01
ERROR 01
E-02
Overtravel
Stop SW was pressed during
E-03
home positioning
E-04
Zero positioning is out of range
E-05
Needle stop position error
E-09
X-axis home position error
E-0A
Thread breakage error
E-0B
ERROR 0B
E-0C
ERROR 0C
E-0D
ERROR 0D
E-0F
ERROR 0F
E-14
Y-axis home position error
E-15
Press
for reatart.
E-16
ERROR 16
E-17
ERROR 17
E-1A
ERROR 1A
E-1C
Restart perimeter
Stop while transferring to next
E-1D
repeat pattern
E-21
Area over
E-22
Area over
E-23
Area over
E-24
Area over
E-25
Area over
E-26
Area over
E-27
Area over
E-28
Area over
E-29
Area over
E-2A
Area over
E-2B
Area over
136
Error
No error occurs.
Either motor of main shaft, X- or Y-axis has
locked.
Overtravel occurs during home position detect-
ing movement.
The stop switch is pressed during home position
detecting movement.
Zero detecting movement out of range
Needle stop position error
X-axis home position detection error
Thread breaking error
Stop or emergency stop during sewing
Insufficient bobbin thread
The machine does not return to the home position.
Undefined error
Y-axis home position error
Stop error during SSP processing (when press-
ing the stop key while the hoop is moving)
Needle with specified number is out of movable
area.
Speed Vol. No. is out of range.
Destination coordinates error
The machine stops during mask tracing.
The machine stops while the needle is moving
between patterns during repeat sewing.
Errors E-1C and E-1D are not displayed due to mechanical problems.
Hoop overhang(+X)
Hoop overhang(+Y)
Hoop overhang(+X, +Y)
Hoop overhang(-X)
Hoop overhang(+X, -X)
Hoop overhang(-X, +Y)
Hoop overhang(+X, -X, +Y)
Hoop overhang(-Y)
Hoop overhang(+X, -Y)
Hoop overhang(+Y, -Y)
Hoop overhang(+X, +Y, -Y)
BES-116AC
Measures
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the area sensor is faulty.
Press the
to restart the home position detecting movement
STOP
again.
Turn the power off and on once. If the same error occurs
again, the home position sensor is faulty.
Adjust the pulley stop position (100 degrees) above the
needle and press the
.
STOP
Turn the power off and on once. If the same error occurs
again, the X-axis mechanism is faulty.
After passing through the thread, press the
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the Y-axis mechanism is faulty.
Hoop movement restarts if you press
This is not usually displayed.
Tracing is cancelled if the
key is pressed when the ma-
STOP
chine is stopped during mask tracing. Press the
continue tracing.
This is displayed when the stop switch is pressed while the
hoop is moving. Press the
to move the hoop again. (It is
necessary to press the
again to start sewing.)
Pattern or the needle position is out of the embroidering area.
Reset the embroidering area on the panel or move the hoop to
the sewable position.
.
STOP
.
key to
Advertisement
Table of Contents
