Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cisco ME-C6524GS-8S
Summary of Contents for Cisco ME-C6524GS-8S
- Page 1 Cisco ME 6500 Series Ethernet Switch Installation Guide October 2009 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-8900-03...
- Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
-
Page 3: Table Of Contents
Shock and Vibration System Grounding Preventing Electrostatic Discharge Damage Power Requirements Power Connection Guidelines for AC-Powered Systems 2-10 Power Connection Guidelines for DC-Powered Systems 2-10 Cabling Requirements 2-11 Site Preparation Checklist 2-11 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... - Page 4 Required Tools Removing the AC-Input Power Supply Installing the AC-Input Power Supply Removing and Installing the Fan Tray Required Tools Removing the Fan Tray Installing the Fan Tray Upgrading the Memory 4-10 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 5 400 W DC-Input Power Supply 400 W AC-Input Power Supply 400 W Power Supply AC Power Cords SFP Transceiver Specifications A P P E N D I X N D E X Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 6 Contents Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 7: Preface
Preface This preface describes who should read the Cisco ME 6500 Series Ethernet Switch Installation Guide, how it is organized, and its document conventions. Audience Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the equipment described in this publication. -
Page 8: Conventions
Means reader take note. Notes contain helpful suggestions or references to material not covered in the Note publication. Cautions use the following conventions: Means reader be careful. In this situation, you might do something that could result in equipment Caution damage or loss of data. Cisco ME 6500 Series Ethernet Switch Installation Guide viii OL-8900-03... -
Page 9: Statement 1071-Warning Definition
éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... - Page 10 Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 11 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 12 Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 13 Preface Conventions Cisco ME 6500 Series Ethernet Switch Installation Guide xiii OL-8900-03...
-
Page 14: Related Documentation
Preface Related Documentation Related Documentation For additional Cisco ME 6500 series Ethernet switch information, refer to these publications: Regulatory Compliance and Safety Information for the Cisco ME 6500 Series Ethernet Switches • Cisco ME 6500 Series Ethernet Switch Software Configuration Guide •... -
Page 15: Obtaining Documentation And Submitting A Service Request
Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html... - Page 16 Preface Obtaining Documentation and Submitting a Service Request Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 17: Chapter 1 Product Overview
• Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) The ME 6524 Ethernet switch (ME-C6524GS-8S) is a member of the Cisco ME 6500 series Ethernet switches. The Cisco ME 6524 Ethernet switch (ME-C6524GS-8S) is a 1.5 RU horizontal chassis with 24 SFP downlink ports and 8 SFP uplink ports. - Page 18 Power supply terminal block (DC-input power shown) supply only) Fan tray Power on/off switch (DC-input power supply) Table 1-1 lists the features of the Cisco ME 6524 Ethernet switch (ME-C6524GS-8S) chassis. Table 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Features Feature Description Chassis 1.5 RU height, fixed configuration chassis...
- Page 19 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Table 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Features (continued) Feature Description Power supplies Supports one or two power supplies. The following power supplies are • supported: PWR-400W-DC (400 W DC-input power supply) –...
- Page 20 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Table 1-1 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Features (continued) Feature Description Chassis front panel features STATUS LED The STATUS LED indicates the system health. Green—The system is operating normally.
- Page 21 Blinking amber—The system has detected a fault with the link. Off—No link is established or the SFP transceiver is not installed. • Table 1-2 lists the physical and environmental specifications of the Cisco ME 6524 Ethernet switch (ME-C6524GS-8S) chassis. Table 1-2 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Specifications...
- Page 22 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Table 1-2 Cisco ME 6524 Ethernet Switch (ME-C6524GS-8S) Specifications (continued) Item Specification Shock and vibration This switch complies with Network Equipment Building Systems (NEBS) (Zone 4 per GR-63-Core) in the following areas: Earthquake environment and criteria •...
-
Page 23: Cisco Me 6524 Ethernet Switch (Me-C6524Gt-8S)
Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) The Cisco ME 6524 Ethernet switch (ME-C6524GT-8S) is a member of the Cisco ME 6500 series Ethernet switches. The Cisco ME 6524 Ethernet switch (ME-C6524GT-8S) is a 1.5 RU horizontal chassis with 24 10/100/1000 downlink ports and 8 1000BASE SFP uplink ports. - Page 24 Power supply status LEDs Power supplies Power supply terminal block Fan tray Power on/off switch Table 1-3 lists the features of the Cisco ME 6524 Ethernet switch (ME-C6524GT-8S) chassis. Table 1-3 Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Features Feature Description Chassis 1.5 RU height, fixed configuration chassis...
- Page 25 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Table 1-3 Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Features (continued) Feature Description Power supplies Supports one or two power supplies. The following power supplies are • supported: PWR-400W-DC (400 W DC-input power supply) –...
- Page 26 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Table 1-3 Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Features (continued) Feature Description Chassis front panel features STATUS LED The STATUS LED indicates the system health. Green—The system is operating normally.
- Page 27 Blinking amber—The system has detected a fault with the link. • Off—No link is established or the SFP transceiver is not installed. • Table 1-4 lists the specifications of the Cisco ME 6524 Ethernet switch (ME-C6524GT-8S) chassis. Table 1-4 Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Specifications Item Specification...
- Page 28 Chapter 1 Product Overview Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Table 1-4 Cisco ME 6524 Ethernet Switch (ME-C6524GT-8S) Specifications (continued) Item Specification Shock and vibration This switch complies with Network Equipment Building Systems (NEBS) (Zone 4 per GR-63-Core) in the following areas: Earthquake environment and criteria •...
-
Page 29: Chapter 2 Preparing For Installation
Statement 258 Before performing any of the following procedures, ensure that power is removed from the DC circuit. Warning Statement 1003 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... - Page 30 Hazardous voltage or energy may be present on DC power terminals. Always replace cover when Warning terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement 1075 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 31: Site Requirements
50°F (10°C) or hotter than 104°F (40°C). The Cisco ME 6524 Ethernet switch is designed to be installed in an environment where there is a sufficient volume of air available to cool the electronics and the power supplies. Any constraints placed on the free flow of air through the chassis or an elevated ambient air temperature can cause the switch to overheat and shut down. -
Page 32: Humidity
If the difference in air temperature exceeds 50°F (10°C), there is insufficient airflow to cool the chassis. A Cisco ME 6524 Ethernet switch that is currently installed in an enclosed or partially enclosed rack Note might meet ambient air temperature and air flow requirements now. However, if you add more chassis, the additional heat generated might cause the ambient air temperature within the rack to exceed 104°F... -
Page 33: Dust And Contamination
Caution properties of the materials used in their construction. Always ground the cables (especially in new cable runs) to a suitable and safe earth ground before connecting them to the system. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 34: Shock And Vibration
Site Requirements Shock and Vibration Cisco ME 6524 Ethernet switches have been shock- and vibration-tested for operating ranges, handling, and earthquake standards to NEBS (Zone 4 per GR-63-Core). These tests have been conducted in earthquake environment and criteria, office vibration and criteria, transportation vibration and criteria, and packaged equipment shock. -
Page 35: Preventing Electrostatic Discharge Damage
• grounding straps are available with banana plugs, metal spring clips, or alligator clips. All Cisco ME 6524 Ethernet switch chassis are equipped with an ESD connector (identified by the ground symbol next to the connector) on the front panel. - Page 36 If you are using an ESD wrist strap that is equipped with an alligator clip, attach the alligator clip directly over the head of the system ground lug screw or to the system ground lug barrel. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 37: Power Requirements
One AC-input power supply and one DC-input power supply The next two sections provide basic guidelines for connecting AC-input power supplies to the site source AC and for connecting DC-input power supplies to the site source DC. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 38: Power Connection Guidelines For Ac-Powered Systems
Ensure that all power connection wiring conforms to the rules and regulations in the National • Electrical Code (NEC) and any additional local codes. Ensure that the DC return remains isolated from the system frame and the chassis (DC-I). • Cisco ME 6500 Series Ethernet Switch Installation Guide 2-10 OL-8900-03... -
Page 39: Cabling Requirements
We strongly recommend that you locate the power cabling runs and other potential noise sources as far Caution away as practical from LAN cabling that terminates on Cisco equipment. If you cannot separate the long parallel cable runs by at least 3.3 feet (1 meter), we recommend that you shield these potential noise sources by housing them in grounded metallic conduits. - Page 40 Distance limitations for signaling • Site wiring • RFI levels • 1. Verify that each power supply installed in the chassis has a dedicated AC source or DC source circuit. Cisco ME 6500 Series Ethernet Switch Installation Guide 2-12 OL-8900-03...
-
Page 41: Warnings
C H A P T E R Installing the Switch This chapter describes how to install the Cisco ME 6500 series Ethernet switch and contains these sections: Preparing for Installation, page 3-1 • Rack-Mounting, page 3-4 • Desk-Top Mounting, page 3-7 •... - Page 42 Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 43 Avoid direct exposure to the laser beam. Statement 1012 Warning Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 44: Verifying Package Contents
Carefully remove the contents from the shipping container, and check each item for damage. If any item is missing or damaged, contact your Cisco representative or reseller for support. Return all packing material to the shipping container, and save it. -
Page 45: Attaching L Brackets To The Chassis
65 24 G S US B FL AS Front-mounting position M4 Phillips flat-head screws OU TP UT INP UT FA N OU TP UT INP UT FA N Rear-mounting position M4 Phillips flat-head screws Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 46: Installing The Chassis In The Rack
Figure 3-2 (bottom view) shows how to install a chassis in a rack when the chassis has the L brackets attached at the rear of the chassis. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 47: Installing The Chassis In The Rack
(See Figure 3-3.) Place the switch right-side up, and position it on the desk or shelf close to where the DC source and the Step 3 system ground are located. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 48: Installing The System Ground
The length of the grounding wire depends on the proximity of the switch to proper grounding facilities. No. 1 Phillips screwdriver. • Wire-stripping tool to remove the insulation from the grounding wire. • • Crimping tool to crimp the grounding wire to the grounding lug. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 49: Connecting Source Power To The Chassis
Connecting Source DC to the DC-Input Power Supply, page 3-10 • Connecting Source AC to the AC-Input Power Supply, page 3-11 • The ME6524 switches support mixing AC-input and DC-input power supplies in the same chassis. Note Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 50: Connecting Source Dc To The Dc-Input Power Supply
Remove any safety flag and lockout devices or any tape from the circuit breaker switch handle, and Step 9 restore power by moving the circuit breaker switch handle to the on (|) position. Cisco ME 6500 Series Ethernet Switch Installation Guide 3-10 OL-8900-03... -
Page 51: Connecting Source Ac To The Ac-Input Power Supply
65 24 G S US B FL AS The accessory kit that shipped with your Cisco ME 6524 Ethernet switch contains a cable to connect a Note terminal or modem to the console port. To connect a terminal to the console port using the cable and adapters provided, follow these steps: Connect one end of the console port cable to the CONSOLE port using the RJ-45-to-RJ-45 cable. -
Page 52: Installing The Sfp Transceivers
Use only Cisco SFP transceivers on the Cisco ME 6524 Ethernet switch. Each SFP transceiver has an internal serial EEPROM that is encoded with security information. This encoding allows Cisco to identify and validate that the SFP transceiver meets the requirements for the switch. - Page 53 Pivot the SFP transceiver bail-clasp fully down to lock the transceiver in place, and immediately reinstall Step 5 the dust plugs. Figure 3-7 Installing an SFP Transceiver into an SFP Transceiver Socket Cisco ME 6500 Series Ethernet Switch Installation Guide 3-13 OL-8900-03...
- Page 54 For complete information about inspecting and cleaning fiber-optic connections, see the document at this URL: http://www.cisco.com/en/US/tech/tk482/tk607/technologies_white_paper09186a0080254eba.shtml Remove the dust plugs from the SFP transceiver optical bores. Step 8 Immediately attach the network interface cable LC connector to the SFP transceiver. Step 9 Cisco ME 6500 Series Ethernet Switch Installation Guide 3-14 OL-8900-03...
-
Page 55: Powering Up The Chassis
CLI from the console to configure the switch as a member of a cluster or as an individual switch. See the Cisco ME 6500 Series Ethernet Switch Software Configuration Guide and the Cisco ME 6500 Series Ethernet Switch Cisco IOS Command Reference on Cisco.com for information on using the CLI with a Cisco ME 6524 Ethernet switch. - Page 56 Chapter 3 Installing the Switch Where to Go Next Cisco ME 6500 Series Ethernet Switch Installation Guide 3-16 OL-8900-03...
- Page 57 Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Removing and Installing the DC-Input Power Supply This section describes how to remove and install the DC-input power supplies in the Cisco ME 6524 Ethernet switch chassis and contains these subsections: Required Tools, page 4-2 •...
-
Page 58: C H A P T E R 4 Removal And Replacement Procedures
EMI gaskets. Step 7 If the power supply bay is to remain empty, install a blank faceplate (Cisco part number 700-20988-xx) over the opening, and secure it with the two captive installation screws. Cisco ME 6500 Series Ethernet Switch Installation Guide... - Page 59 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supply Figure 4-1 Removing the DC-Input Power Supply Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 60: Installing The Dc-Input Power Supply
DC cables. They should be sized according to local and national installation requirements and electrical codes. The wire should be sized according to local and national installation requirements and electrical Note codes. Use only copper wire. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... - Page 61 Verify the power supply operation by ensuring that the power supply front panel LEDs are in these states: Step 13 INPUT OK LED is green • FAN OK LED is green • OUTPUT OK is green • Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 62: Removing And Installing The Ac-Input Power Supply
Figure 4-2 Installing the DC-Input Power Supply Removing and Installing the AC-Input Power Supply This section describes how to remove and install the AC-input power supply in the Cisco ME 6524 Ethernet switch chassis and contains the following subsections: •... -
Page 63: Removing The Ac-Input Power Supply
When sliding the power supply into or out of the power supply bay, be careful not to damage the EMI gaskets. If the power supply bay is to remain empty, install a blank faceplate (Cisco part number 700-20988-xx) Step 5 over the opening, and secure it with the two captive installation screws. -
Page 64: Installing The Ac-Input Power Supply
As an added check, verify that you can hear the power supply fan operating. Removing and Installing the Fan Tray This section describes how to remove and install the fan tray in the Cisco ME 6524 Ethernet switch chassis and contains these subsections: Required Tools, page 4-8 •... -
Page 65: Removing The Fan Tray
Slide the fan tray into the fan tray bay until the power connector seats in the chassis fan connector and the captive installation screw makes contact with the chassis. Step 4 Tighten the captive installation screw. Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... -
Page 66: Upgrading The Memory
In order to remove the cover from the chassis, you must first remove both power supplies from the Note chassis. To upgrade the SP and the RP memory on the Cisco ME 6524 Ethernet switch, follow these steps: If your chassis is equipped with one or two DC-input power supplies, remove them from the chassis. Step 1 Refer to the “Removing and Installing the DC-Input Power Supply”... - Page 67 DRAM DIMM up away from the tabs. Be careful not to bend the locking spring tabs too far, because you can break them. (See Figure 4-6.) Cisco ME 6500 Series Ethernet Switch Installation Guide 4-11 OL-8900-03...
- Page 68 DIMM into the socket connector. A notch (key) is located on the left connector edge of the DIMM. This notch key ensures that Note the DIMM is correctly oriented in the socket. Cisco ME 6500 Series Ethernet Switch Installation Guide 4-12 OL-8900-03...
-
Page 69: Installing The Dc-Input Power Supply
When inserting the DIMM, use firm but not excessive pressure. If you damage a socket, you will have Caution to return the main board to Cisco for repair. Press down on the edges of the DRAM DIMM until the DIMM socket tabs click into place on both sides Step 10 of the DRAM DIMM locking the DIMM in place. - Page 70 Chapter 4 Removal and Replacement Procedures Upgrading the Memory Cisco ME 6500 Series Ethernet Switch Installation Guide 4-14 OL-8900-03...
-
Page 71: Appendix
A P P E N D I X Power Supply Specifications This appendix provides the specifications for the Cisco ME 6500 series Ethernet switch power supplies. Two power supply models are available: 400 W DC-Input Power Supply, page A-1 •... - Page 72 Red—A power supply fan failure is detected. • OUTPUT OK Red—A problem with the DC-output voltage from • • the power supply is detected. Green—The DC-output voltage is within • acceptable margins. Weight 4.41 lb (2.0 kg) Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 73: 400 W Dc-Input Power Supply
Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max) • High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max) • AC-input current AC-input frequency 50/60 Hz (nominal) (±3% for full range) Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... - Page 74 OUTPUT OK LED is lit red rather than unlit on the power supply that is powered off. Weight 4.41 lb (2 kg) Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 75: 400 W Power Supply Ac Power Cords
1. Plug contains a 13 A fuse. Figure A-3 CAB-ACR (Argentina) Power Cord Cordset rating: 10 A, 250 V Length: 8 ft. 2 in. (2.5 m) Plug: IRAM 2073 Connector: IEC 60320 C13 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03... - Page 76 Length: 8 ft 2 in. (2.5 m) Plug: GB16C Connector: IEC 60320 C13 Figure A-6 CAB-ACI (Italy) Power Cord Cordset rating: 10A, 250V Length: 8 ft. 2 in. (2.5 m) Plug: CEI 23-16/7 Connector: IEC 60320 C13 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 77 Length: 6 ft. 7 in. (2 m) Connector: IEC 60320 C13 Figure A-9 CAB-AC-250V/13A(North America) Power Cord Cordset rating: 13 A, 250 V Length: 6 ft. 7 in. (2 m) Plug: NEMA 6-20 Connector: IEC 60320 C13 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
- Page 78 Plug: JIS C8303 Connector: IEC 60320 C13 Figure A-12 CAB-ACS (Switzerland) Power Cord Cordset rating: 10 A, 250 V Length: 8 ft. 2 in. (2.5 m) Plug: SEV 1011 Connector: IEC 60320 C13 Cisco ME 6500 Series Ethernet Switch Installation Guide OL-8900-03...
-
Page 79: Appendix
A P P E N D I X SFP Transceiver Specifications This appendix provides cabling specifications for the SFP transceivers supported on the Cisco ME 6500 Ethernet switch. Figure B-1 shows an optical SFP transceiver with the major features labeled. - Page 80 Appendix B SFP Transceiver Specifications Table B-1 lists the specifications and cabling distances for the SFP transceivers. Table B-1 SFP Transceiver Port Cabling Specifications Modal SFP Transceiver SFP Transceiver Wavelength Core Size Bandwidth Product Number Type (nm) Fiber Type (micron) (MHz/km) Cable Distance GLC-T...
- Page 81 Appendix B SFP Transceiver Specifications Table B-2 lists the fiber loss budgets for the 100-MB SFP transceivers. Table B-2 Fiber Loss Budgets for the 100-MB SFP Transceivers 100-MB SFP Transceiver Transmit (dBm) Receive (dBm) Product Number GLC-FE-100BX-U –8 (maximum) –7 (maximum) –14 (minimum) –28.2 (minimum) GLC-FE-100BX-D...
- Page 82 Storage temperature -40° to 185°F (-40° to 85°C) You can use any combination of SFP modules that your Cisco device supports. The only restrictions are Note that each SFP port must match the wavelength specifications on the other end of the cable and that the cable must not exceed the stipulated cable length for reliable communications.
- Page 83 Appendix B SFP Transceiver Specifications Figure B-3 CWDM SFP Transceiver Color arrow on label Dustplug Receive optical bore Transmit optical bore Bail clasp DWDM SFP transceivers are used as part of a DWDM optical network to provide high-capacity bandwidth across an optical fiber network. There are 32 fixed-wavelength DWDM SFPs that support the International Telecommunications Union (ITU) 100-GHz wavelength grid.
- Page 84 Appendix B SFP Transceiver Specifications Table B-6 DWDM SFP Transceiver Product Numbers, Wavelengths, and ITU Channel Numbers (continued) DWDM SFP Description ITU Channel Product Number DWDM-SFP-4851 1000BASE-DWDM 1548.51 nm SFP DWDM-SFP-4772 1000BASE-DWDM 1547.72 nm SFP DWDM-SFP-4692 1000BASE-DWDM 1546.92 nm SFP DWDM-SFP-4612 1000BASE-DWDM 1546.12 nm SFP DWDM-SFP-4453...
-
Page 85: I N D E X
DC 3-10 ME-C6524GS-8S Ethernet switches heat dissipation ME-C6524GT-8S Ethernet switches 1-12 input current AC power cords input voltages illustrations A-5 to A-8 installing specifications table LEDs Cisco ME 6500 Series Ethernet Switch Installation Guide IN-1 OL-8900-03... - Page 86 LED fan trays installing features table FAN LED 1-10 physical characteristics fan tray power supplies removal and replacement procedure description required tools shock and vibration specifications specifications Cisco ME 6500 Series Ethernet Switch Installation Guide IN-2 OL-8900-03...
- Page 87 ME-C6524GS-8S Ethernet switches 400W DC-input power supply (figure) ME-C6524GT-8S Ethernet switches 1-12 AC-input power supplies installation procedure signaling and pinouts AC-input power supplies removal procedure terminal setup 3-12 AC power cords Cisco ME 6500 Series Ethernet Switch Installation Guide IN-3 OL-8900-03...
- Page 88 ME-C6524GT-8S Ethernet switches 1-12 ME-C6524GS-8S Ethernet switches ME-C6524GT-8S Ethernet switches 1-11 STATUS LED 1-10 system ground accessory kit connecting grounding lug guidelines tools required telco racks uplink port LEDs 1-11 Cisco ME 6500 Series Ethernet Switch Installation Guide IN-4 OL-8900-03...