hit counter script
Cisco 2431 - IAD Router Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 2431 - IAD Router
  6. Hardware installation manual
Cisco 2431 - IAD Router Hardware Installation Manual

Cisco 2431 - IAD Router Hardware Installation Manual

Ethernet access switch
Hide thumbs Also See for 2431 - IAD Router:
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco ME 2400 Ethernet Access Switch
Hardware Installation Guide
November 2005
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: OL-7678-01

Advertisement

Table of Contents
loading

Related Manuals for Cisco 2431 - IAD Router

Summary of Contents for Cisco 2431 - IAD Router

  • Page 1 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide November 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-7678-01...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...

  • Page 3: Table Of Contents

    C H A P T E R Setting up the Switch Features Front Panel Description Front Panel Descriptions 10/100 Ports SFP Module Slots SFP Modules SFP Module Patch Cable LEDs System LED Port LEDs Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 4 Connecting to Fiber-Optic SFP Modules 2-23 Connecting to 1000BASE-T SFP Modules 2-24 Where to Go Next 2-25 Troubleshooting C H A P T E R Understanding POST Results Diagnosing Problems Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 5 Taking Out What You Need Connecting to the Console Port Starting the Terminal-Emulation Software Connecting to a Power Source Entering the Initial Configuration Information IP Settings Completing the Setup Program N D E X Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 6 Contents Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 7: Preface

    Cisco.com Product Documentation home page. For information about the standard Cisco IOS Release 12.1 or 12.2 commands, see the Cisco IOS documentation set from the Cisco.com home page at Service and Support > Technical Documents. On the Cisco Product Documentation home page, select Release 12.1 or 12.2 from the Cisco IOS Software drop-down list.

  • Page 8: Conventions

    Appendix C, “Connecting to DC Power”describes how to connect the Cisco ME switch to a direct current (DC)-input power source. Appendix D, “Configuring the Switch with the CLI-Based Setup Program,”...
  • Page 9 å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 10 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 11 Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 12 Preface Conventions Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 13: Related Publications

    Release Notes for the Cisco ME 2400 Ethernet Access Switch (not orderable but available on • Cisco.com) Before installing, configuring, or upgrading the switch, see the release notes on Cisco.com for the latest Note information. Release Notes for the Cisco ME 2400 Ethernet Access Switch (not orderable but available on •...

  • Page 14: Obtaining Documentation

    Cisco products and to view technical documentation in HTML. With the DVD, you have access to the same documentation that is found on the Cisco website without being connected to the Internet. Certain products also have .pdf versions of the documentation available.

  • Page 15: Ordering Documentation

    Preface Documentation Feedback The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com users (Cisco direct customers) can order a Product Documentation DVD (product number DOC-DOCDVD=) from Cisco Marketplace at this URL: http://www.cisco.com/go/marketplace/ Ordering Documentation Beginning June 30, 2005, registered Cisco.com users may order Cisco documentation at the Product...

  • Page 16: Reporting Security Problems In Cisco Products

    Obtaining Technical Assistance Reporting Security Problems in Cisco Products Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you might have identified a vulnerability in a Cisco product, contact PSIRT: •...

  • Page 17: Submitting A Service Request

    Cisco engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

  • Page 18: Obtaining Additional Publications And Information

    Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.com/go/marketplace/ Cisco Press publishes a wide range of general networking, training and certification titles. Both new • and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com...

  • Page 19: Chapter 1 Product Overview

    The Cisco Metro Ethernet (ME) 2400 Ethernet Access switch—also referred to as the switch—is an Ethernet access switch to which you can connect other network devices such as routers, other switches, a home access gateway (HAG), or a computer. This chapter provides a functional overview of the Cisco ME switch. These topics are included: Setting up the Switch, page 1-1 •...

  • Page 20: Front Panel Description

    Note 1000 Mbps in full-duplex mode or at 10 or 100 Mbps in half-duplex mode. By default, the SFP module ports on the Cisco ME switch are configured as network node Note interfaces (NNIs). A port can be reconfigured from user network interface (UNI) to NNI and the reverse, but only four ports on the switch can be NNIs at the same time.

  • Page 21: Front Panel Descriptions

    (port 2) on the left. Port 3 is above port 4, and so on, as shown in Figure 1-1 (the Cisco ME AC switch) and Figure 1-2 (the Cisco ME DC switch). The SFP module slots are numbered 1 and 2. Figure 1-1 Cisco ME 2400 AC Ethernet Access Switch Front Panel...

  • Page 22: Sfp Module Slots

    UNIs and NNIs are supported on the Cisco ME switch. UNIs are typically connected to a host, such as a PC or a Cisco IP Phone. By default, the 10/100 ports on the Cisco ME switch are configured as UNIs.

  • Page 23: Sfp Module Patch Cable

    Product Overview Front Panel Description SFP Module Patch Cable The Cisco ME switch supports the SFP module patch cable, a 1/2 meter, copper, passive cable with SFP module connectors at each end (see Figure 1-3). The patch cable can connect two Cisco ME switches in a cascaded configuration.

  • Page 24: Port Leds

    CRC errors, and alignment and jabber errors are monitored for a link-fault indication. Amber Port is disabled. Rear Panel Description The Cisco ME switch rear panel has a cable lock and an exhaust fan. (See Figure 1-5.) Figure 1-5 Cisco ME Switch Rear Panel...

  • Page 25: Power Connectors

    AC power connector to an AC power outlet. Cisco ME DC Switch Power Supply The Cisco ME DC switch power supply supports input voltages between –36 to –72 VDC, 1 to 2 A. Appendix C, “Connecting to DC Power,”...

  • Page 26: Network Configurations

    Network Configurations See the switch software configuration guide on Cisco.com for an explanation of network configuration concepts. The software configuration guide also provides examples of network configurations that use the switch to create dedicated network segments that are interconnected through Ethernet connections.

  • Page 27: Preparing For Installation

    C H A P T E R Switch Installation This chapter describes how to start your Cisco Metro Ethernet (ME) switch and how to interpret the power-on self-test (POST) that ensures proper operation. It also describes how to install the switch and how to make connections to the switch.

  • Page 28: Chapter 2 Switch Installation

    • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006 Class 1 laser product. Statement 1008 Warning Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 29 When installing or replacing the unit, the ground connection must always be made first and Warning disconnected last. Statement 1046 Warning No user-serviceable parts inside. Do not open. Statement 1073 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 30: Installation Guidelines

    1310 32,810 feet (10 km) (100BASE-LX10) 1000BASE-BX10-D 1490 TX G.652 — 32,810 feet (10 km) (GLC-BX-D) 1310 RX 1000BASE-BX10-U 1310 TX G.652 — 32,810 feet (10 km) (GLC-BX-U) 1490 RX Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 31 Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent • lighting fixtures. Make sure that the cabling is safely away from other devices that might damage the cables. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 32: Verifying Package Contents

    Carefully remove the contents from the shipping container, and check each item for damage. If any item Note is missing or damaged, contact your Cisco representative or reseller for support. Return all packing material to the shipping container, and save it.

  • Page 33: Verifying Switch Operation

    POST completes, the system LED blinks amber. If POST fails, the system LED remains amber. If POST completes successfully, the system LED rapidly blinks green. POST failures are usually fatal. Call Cisco Systems if your switch does not pass POST. Note Powering Off the Switch After a successful POST, disconnect the power cord from the switch.

  • Page 34: Removing Screws From The Switch

    Installing the switch in a 24-inch rack requires an optional bracket kit that is not included with the Note switch. You can order a kit containing the 24-inch rack-mounting brackets and hardware from Cisco. The kit part number is RCKMNT-1RU= (700-12398-XX).

  • Page 35: Attaching Brackets To The Switch

    For 24-inch racks, use part number RCKMNT-24IN-1RU (700-13248-XX), and see Attaching • Brackets to 24-Inch Racks, page 2-12. • For ETSI racks, use part number RCKMNT-ETSI-1RU= (700-19781-XX), and see Attaching Brackets for ETSI Racks, page 2-14. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 36 Attaching Brackets for 19-Inch Telco Racks to a Cisco ME Switch, Figure 2-5 on page 2-11 Figure 2-3 Attaching Brackets for 19-Inch Racks to a Cisco ME Switch, Front Panel Forward SY ST EM R A T IN 1 0 0 -2 4 0 V ~ 1 A -0 .5...
  • Page 37 Attaching Brackets for 23-Inch Telco Racks to a Cisco ME Switch, Figure 2-8 on page 2-12 • Figure 2-6 Attaching Brackets for 23-Inch Racks to a Cisco ME Switch, Front Panel Forward SY ST EM R A T IN 1 0 0 -2 4 0 V ~ 1 A -0 .5...
  • Page 38 Chapter 2 Switch Installation Installing the Switch Figure 2-7 Attaching Brackets for 23-Inch Racks to a Cisco ME Switch, Rear Panel Forward Phillips flat-head screws Figure 2-8 Attaching Brackets for 23-Inch Telco Racks to a Cisco ME Switch C is co M...
  • Page 39 Chapter 2 Switch Installation Installing the Switch Figure 2-9 Attaching Brackets for 24-Inch Racks to a Cisco ME Switch, Front Panel Forward SY ST EM R A T IN 1 0 0 -2 4 0 V ~ 1 A -0 .5...
  • Page 40 Attaching Brackets for ETSI Telco Racks to a Cisco ME Switch, Figure 2-14 on page 2-15 Figure 2-12 Attaching Brackets for ETSI Racks to a Cisco ME Switch, Front Panel Forward SY ST EM R A T IN 1 0 0 -2 4 0 V ~ 1 A -0 .5...

  • Page 41: Mounting The Switch In A Rack

    • Connect to a 10/100 port and either run the Initial Configuration Dialog or use the CLI to set up your switch. See the Cisco ME 3400 and ME 2400 Ethernet Access Switches Getting Started Guide for instructions. Connect to the front-panel ports. See the “Connecting to the 10/100 Ports”...

  • Page 42: Attaching The Cable Guide

    Use the supplied black screw shown in Figure 2-16 attach the cable guide to the left or right bracket. Figure 2-16 Attaching the Cable Guide on the Cisco ME Switch SYS TEM RA TIN 10 0-2 40 1A -0.

  • Page 43: Mounting The Switch On A Wall

    “Verifying Switch Operation” section on page 2-7. • Connect to a 10/100 port, and run the Initial Configuration Dialog. See the Cisco ME 3400 and ME • 2400 Ethernet Access Switches Getting Started Guide for instructions. Connect to the front-panel ports. See the “Connecting to the 10/100 Ports”...

  • Page 44: Table- Or Shelf- Mounting

    SFP module slots on the front of the Cisco ME switches. These field-replaceable modules provide uplink interfaces. You can use any combination of SFP modules. See the Cisco ME switch release notes for the list of SFP modules that the Cisco ME switch supports. Each port must match the wave-length specifications on the other end of the cable, and for reliable communications, the cable must not exceed the stipulated cable length.
  • Page 45 Do not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from the Caution fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide 2-19 OL-7678-01...

  • Page 46: Removing Sfp Modules From Sfp Module Slots

    For fiber-optic SFP modules, insert a dust plug into the optical ports of the SFP module to keep the optical interfaces clean. Step 6 Place the removed SFP module in an antistatic bag or other protective environment. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide 2-20 OL-7678-01...

  • Page 47: Inserting And Removing The Sfp Module Patch Cable

    C is co M E 2 4 0 0 SE RI ES Step 3 Repeat these steps for the second Cisco ME switch to which you want to cascade the first switch. Figure 2-23. Figure 2-23 Connecting Two Cisco ME Switches with an SFP Module Patch Cable...

  • Page 48: Connecting To The 10/100 Ports

    Note On user network interface (UNI) ports, the port LED is green after the link is established. It does not turn amber because. STP is not supported. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide 2-22 OL-7678-01...

  • Page 49: Connecting To Sfp Modules

    C is co M E 3 4 0 0 SE RI ES LC connector Insert the other cable end into a fiber-optic connector on a target device. Step 3 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide 2-23 OL-7678-01...

  • Page 50: Connecting To 1000Base-T Sfp Modules

    10/100 or 1000BASE-T SFP module port on the switch, regardless of the type of device on the other end of the connection. Insert the other cable end in an RJ-45 connector on a target device. Step 2 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide 2-24 OL-7678-01...

  • Page 51: Where To Go Next

    Use the CLI from the console to configure the switch. See the switch software configuration guide • or the switch command reference on for information about using the CLI with a Cisco ME switch. For setup instructions that use the CLI setup program, go to Appendix D, “Configuring the Switch...
  • Page 52 Chapter 2 Switch Installation Where to Go Next Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide 2-26 OL-7678-01...

  • Page 53: Chapter 3 Troubleshooting

    POST completes, the system LED blinks amber. If POST fails, the system LED remains amber. If POST completes successfully, the system LED rapidly blinks green. POST failures are usually fatal. Call Cisco Systems if your switch does not pass POST. Note...
  • Page 54 For SFP module port • See your SFP module connections: documentation for cabling guidelines. The distance between the – SFP module port and the attached device exceeds the SFP module cabling guidelines. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 55 See the switch command reference guide for information on the errdisable recovery command. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 56 Refer to the switch command reference guide for information on the errdisable recovery command. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 57: Appendix

    Technical Specifications This appendix lists the switch technical specifications in Table A-1. Table A-1 Technical Specifications for the Cisco ME 2400 Ethernet Access Switch Environmental Ranges Operating temperature 32 to 113°F (0 to 50°C) Storage temperature –13 to 158°F (– 25 to 70°C)
  • Page 58 Appendix A Technical Specifications Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 59: Appendix

    A P P E N D I X Connector and Cable Specifications This appendix describes the Cisco ME switch ports and the cables and adapters that you use to connect the switch to other devices. Connector Specifications These sections describe the connectors used with the switch.

  • Page 60: Sfp Module Ports

    This applies only to switches on which auto-MDIX is disabled. SFP Module Ports The Cisco ME switch uses SFP modules for fiber-optic and copper uplinks. See the Cisco ME switch release notes for a list of supported SFP modules. Figure B-2 Fiber-Optic SFP Module LC Connector Invisible laser radiation may be emitted from disconnected fibers or connectors.

  • Page 61: Console Port

    PC. You need to provide a RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console port to a terminal. You can order a kit (part number ACS-DSBUASYN=) containing that adapter from Cisco. For console port and adapter pinout information, see...

  • Page 62: Four Twisted-Pair Cable Pinouts For 1000Base-T Ports

    1 TP0+ 2 TPO- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+ 5 TP2- 5 TP2- 7 TP3+ 7 TP3+ 8 TP3- 8 TP3- Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 63: Crossover Cable And Adapter Pinouts

    RJ-45-to-DB-9 adapter cable, and the console device. Table B-1 Console Port Signaling Using a DB-9 Adapter Switch Console RJ-45-to-DB-9 Console Port (DTE) Terminal Adapter Device Signal DB-9 Pin Signal Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 64 The RJ-45-to-DB-25 female DTE adapter is not supplied with the switch. You can order a kit (part number Note ACS-DSBUASYN=) containing this adapter from Cisco. Table B-2 Console Port Signaling Using a DB-25 Adapter Switch Console RJ-45-to-DB-25 Console Port (DTE) Terminal Adapter Device Signal DB-25 Pin Signal Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 65: Appendix

    A P P E N D I X Connecting to DC Power To connect the Cisco ME switch to a DC-input power source, follow these steps: Preparing for Installation, page C-1 Grounding the Switch, page C-2 Wiring the DC-Input Power Source, page C-5 Ethernet cables must be shielded when used in a central office environment.

  • Page 66: Grounding The Switch

    Slide the open end of the ground lug over the exposed area of the 6-gauge wire. Step 3 Using a Panduit crimping tool, crimp the ground lug to the 6-gauge wire. Step 4 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 67 Using a ratcheting torque screwdriver, torque each ground-lug screw to 15 lbf-in. (240 ounce-force Step 6 inches [ozf-in.]). Figure C-3 shows how to torque the ground screws on a Cisco ME DC switch. Figure C-3 Torquing Ground-Lug Screws Torque to 15 lbf-in.

  • Page 68: Connecting The Grounding Wire To Earth Ground

    Ci sco M E 34 00 SER IES Telco rack Grounding wire Figure C-5 Connecting the Grounding Wire to the Rack (Grounding) from the Rear-Panel Ground Connector Telco rack Grounding wire Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 69: Wiring The Dc-Input Power Source

    Warning Statement 1030 You must connect the Cisco ME DC switch only to a DC-input power source that has an input supply Caution voltage from –36 to –72 VDC. If the supply voltage is not in this range, the switch might not operate properly or might be damaged.
  • Page 70 Insert the exposed wire of one of the four DC-input power source wires into the terminal block plug, as shown in Figure C-9. Make sure that you cannot see any wire lead. Only wire with insulation should extend from the terminal block. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 71 Use a ratcheting torque screwdriver to torque the terminal block captive screw (above the installed wire Step 6 lead) to 4.5 lbf-in. (72 ozf-in.). (See Figure C-10.) Do not overtorque the terminal-block captive screws. The recommended maximum torque is 4.5 lbf-in. Caution Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 72 Supply (negative) Feed A Supply (negative) Feed B Step 8 Insert the terminal block plug in the terminal block header on the front panel of the switch. (See Figure C-12). Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 73 C U R R E N T 2 – 1 C O N S O Remove the tape from the circuit-breaker switch handle, and move the circuit-breaker handle to the Step 9 on position. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 74 Appendix C Connecting to DC Power Wiring the DC-Input Power Source Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide C-10 OL-7678-01...

  • Page 75: Appendix

    “Connecting to the Console Port” section on page D-3 “Starting the Terminal-Emulation Software” section on page D-4 • “Connecting to a Power Source” section on page D-5 • “Entering the Initial Configuration Information” section on page D-5 • Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 76: Taking Out What You Need

    Taking Out What You Need Remove the items shown in Figure D-1 from the shipping container: Figure D-1 The Cisco ME Switch, Adapter Cable, and AC Power Cord SYST EM INP UT -36 CUR REN – -72 V T 2 – 1A...

  • Page 77: Connecting To The Console Port

    Figure D-1 Figure D-2. Attach the DB-9 female DTE of the adapter cable to a PC serial port, or attach an appropriate adapter to Step 2 the terminal. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 78: Starting The Terminal-Emulation Software

    Configure the baud rate and character format of the PC or terminal to match these console port default Step 2 characteristics: 9600 baud • 8 data bits • 1 stop bit • No parity • • None (flow control) Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 79: Connecting To A Power Source

    When POST completes, the system LED blinks amber. If POST fails, the system LED remains amber. If POST completes successfully, the system LED rapidly blinks green. POST failures are usually fatal. Call Cisco Systems if your switch does not pass POST. Note If you started the terminal emulation program before you powered on your switch, the PC or terminal displays the bootloader sequence.

  • Page 80: Completing The Setup Program

    Configuring interface vlan1: Configure IP on this interface? [yes]: yes IP address for this interface: 10.4.120.106 Subnet mask for this interface [255.0.0.0]: 255.0.0.0 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 81 To use the CLI, enter commands at the Switch> prompt through the console port by using a terminal program or through the network by using Telnet. For configuration information, see the switch software configuration guide or the switch command reference. Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...
  • Page 82 Appendix D Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide OL-7678-01...

  • Page 83: I N D E X

    2-24 specifications pinouts adapter pinouts, terminal See also connectors and cables RJ-45-to-DB-25 cautions viii RJ-45-to-DB-9 Cisco IOS command-line interface auto-MDIX 2-24 CiscoView autonegotiation accessing through console port Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide IN-1 OL-7678-01...
  • Page 84 2-3, C-2 grounded equipment warning DC power connecting to 2-7, D-5 HP OpenView exposed wire warning warning 2-2, C-5 diagnosing problems disconnect device warning 2-3, C-5 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide IN-2 OL-7678-01...
  • Page 85 SFP module ports mounting brackets POST attaching 2-9, ?? to 2-15 LEDs 3-1, D-5 attaching 19-inch racks 2-10 results 3-1, D-5 attaching 24-inch racks 2-12 attaching ETSI racks 2-14 Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide IN-3 OL-7678-01...
  • Page 86 Telnet, and accessing the CLI description temperature, operating installing and removing 2-21 terminal emulation software SFP modules trained and qualified personnel warning 1000BASE-BX troubleshooting 3-1 to 3-3 1000BASE-LX/LH 1000BASE-SX 1000BASE-T 1000BASE-ZX Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide IN-4 OL-7678-01...
  • Page 87 2-3, C-1 shield Ethernet cables short-circuit (overcurrent) protection 2-2, C-5 short-circuit protection stacking chassis trained and qualified personnel two-poled disconnect two-poled disconnect device wall-mounting Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide IN-5 OL-7678-01...
  • Page 88 Index Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide IN-6 OL-7678-01...

This manual is also suitable for:

Me 2400

Table of Contents