Owner’s Manual of Pioneer® Contents Energy Recovery Ventilator Table of Contents Safety Remarks............................1 Product Information..........................4 Specifications.............................5 Overview..............................8 Installation..............................9 Applicable To Models: Operation..............................12 - ERV035AVTTW5W Wi-Fi Connection............................17 Maintenance...............................21 Troubleshooting............................23 Attention Please read this manual carefully before installing or operating the equipment.
2.1 m (>7 Ft.) above the floor. WARNING! NOT PERMITTED recovery ventilator ERV035AVTTW5W. • Precautions must be taken to prevent the back-flow of gases into the room from any • Installation and operation of the ventilator...
Ventilator Accessories Bag Remote Controller INTRODUCTION User’s Manual This user’s manual includes technical description operation, installation and mounting Packaging Box guidelines, as well as technical data for the heat recovery ventilator ERV035AVTTW5W.
Specifications Specifications MAIN TECHNICAL PARAMETERS TECHNICAL SPECIFICATIONS • The ventilator is designed for indoor applications with an ambient temperature ranging from Description Unit Value -20°C (-4°F) to +50°C (+122°F), and a relative humidity below 80%. Voltage 100-240 Frequency 50/60 • The ventilator is classified as a class II electric appliance. Input Power 9.7/10.7/11.5 Current...
Specifications Overview OPERATION MODES INSTALLATION DRA WING Ventilation Mode - The ventilator runs in exhaust or supply mode at a set speed. When synchronous operation of two connected ventilators occurs, one runs in the supply mode and the other in exhaust mode. Silica Gel Sealing Circle Regeneration Mode - The ventilator runs in two cycles of 75 seconds each, to...
Installation Installation VENTILATOR INSTALLATION 2. Pull the mobile bracket into the outer duct Slightly pull the duct back into place so that the silicone ring on if it is stuck in the wall. Pull the duct further in if the outside of the outer duct is tight against 1.
Page 7
Installation Operation FUNCTION DESCRIPTION Status Light (RGB-LED) 4. Install the main unit on the indoor surface wall. Connect the adapter wire from the back of the main unit to the wiring of the fan and temperature sensor exposed in the inner duct, and tidy ON Status the wiring.
Operation Operation Fan Speed PAIRING SYNCHRONIZATION FUNCTION Indicator Light Working ON/OFF Mode Fan Boost Mode Negative Ion ON/OFF The suggested maximum distance is 50 feet Button cell CR2025 Filter Reset Cover ON/OFF Master Unit Slave Unit Remote Control Please insert the button cell (prepared by user) before attempting to use the controller.
Page 9
Operation Operation Slave Unit Settings MASTER-SLAVE UNIT SETTINGS 1. Connect the device to power. In the OFF state, as shown in the figure, press and hold the mode button of the device for 5 seconds, and the status indicator green light will start flashing slowly. Master Unit Settings Once done, the device enters master-slave linkage mode, and the unit is set to the slave role.
Installation of “Pioneer Airlink” smartphone application Version Search for “Pioneer Airlink” in the Google Play Store (for Android users) or the App Store (for iOS users). Note that a 2.4GHz Wi-Fi connection is needed to use the Wi-Fi control feature.
Page 11
2. When the device is powered on, in the OFF state, long press the ON/OFF button of any 3. Open the downloaded Pioneer Airlink app, device for 5 seconds, the device status 6. After successful Wi-Fi connection, 2.
Maintenance Maintenance MAINTENANCE Fan Maintenance (Once Per Year) Loosen the screws on the top of the main unit. Remove the secured bracket from within the inner duct and take out the fan. After unplugging the connecting wires of the Clean the impeller blades. Use a soft brush, doth, or a vacuum cleaner to clean the impeller. Do not use main unit and the inner duct, remove the main unit and the inner duct from the wall separately.
According to the manual, use the same remote controller controller for the Master-Slave units settings Pioneer product line, parts, and supplies are Excessive metal structures and interference The ventilator is installed where it is sources around will weaken the wireless...