Table of Contents
Advertisement
Cisco Webex Room Panorama and Room 70 Panorama
Introduction
Video Selfview Default FullscreenMode
Define if the main video source (self-view) shall be shown in full screen or as a small
picture-in-picture (PiP) after a call. The setting only takes effect when self-view is switched
on (see the Video Selfview Default Mode setting).
Requires user role: ADMIN, INTEGRATOR
Default value: Current
Value space: Off/Current/On
Off: Self-view will be shown as a PiP.
Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e.
if it was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the
call, it remains fullscreen after the call.
On: The self-view picture will be shown in fullscreen.
Video Selfview Default Mode
Define if the main video source (self-view) shall be displayed on screen after a call. The
position and size of the self-view window is determined by the Video Selfview Default
PIPPosition and the Video Selfview Default FullscreenMode settings respectively.
Requires user role: ADMIN, INTEGRATOR
Default value: Current
Value space: Off/Current/On
Off: Self-view is switched off when leaving a call.
Current: Self-view is left as is, i.e. if it was on during the call, it remains on after the call;
if it was off during the call, it remains off after the call.
On: Self-view is switched on when leaving a call.
D15439.02 Room Panorama and Room 70 Panorama Administrator Guide CE9.14, OCTOBER 2020.
Configuration
Peripherals
Maintenance
Video Selfview Default OnMonitorRole
Define which screen/output to display the main video source (self-view) after a call. The
value reflects the monitor roles set for the different outputs in the Video Output Connector
[n] MonitorRole setting.
The setting applies both when self-view is displayed in full screen, and when it is displayed
as picture-in-picture (PiP).
Requires user role: ADMIN, INTEGRATOR
Default value: Current
Value space: Current/First/Second/Third
Current: When leaving a call, the self-view picture will be retained on the same output as
it was during the call.
First: The self-view picture will be shown on outputs with the Video Output Connector [n]
MonitorRole set to First.
Second: The self-view picture will be shown on outputs with the Video Output
Connector [n] MonitorRole set to Second.
Third: The self-view picture will be shown on outputs with the Video Output Connector
[n] MonitorRole set to Third.
Video Selfview Default PIPPosition
Define the position on screen of the small self-view picture-in-picture (PiP) after a call.
The setting only takes effect when self-view is switched on (see the Video Selfview
Default Mode setting) and fullscreen view is switched off (see the Video Selfview Default
FullscreenMode setting).
Requires user role: ADMIN, INTEGRATOR
Default value: LowerRight
Value space: Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/
LowerLeft/LowerRight
Current: The position of the self-view PiP will be kept unchanged when leaving a call.
UpperLeft: The self-view PiP will appear in the upper left corner of the screen.
UpperCenter: The self-view PiP will appear in the upper center position.
UpperRight: The self-view PiP will appear in the upper right corner of the screen.
CenterLeft: The self-view PiP will appear in the center left position.
CentreRight: The self-view PiP will appear in the center right position.
LowerLeft: The self-view PiP will appear in the lower left corner of the screen.
LowerRight: The self-view PiP will appear in the lower right corner of the screen.
www.cisco.com — Copyright © 2020 Cisco Systems, Inc. All rights reserved.
181
Administrator Guide
Device settings
Device settings
Appendices
Advertisement
Chapters
Table of Contents
