Honeywell EQUIP Series Quick Install Manual
Fixed mini dome network camera
Hide thumbs
Also See for EQUIP Series:
- Installation and configuration manual (148 pages) ,
- Instruction manual (102 pages) ,
- User manual (100 pages)
Advertisement
Quick Links
EQUIP™ Series Fixed
Mini Dome Network Camera
Quick Install Guide
Thank you for purchasing a Honeywell EQUIP Series Fixed Mini Dome
Network Camera. Before installing the camera, please verify your
model and read this guide carefully:
HD4DIP, NTSC, 2.8 - 10 mm Vari-focal Auto Iris lens
HD4DIPX, PAL, 2.8 - 10 mm Vari-focal Auto Iris lens
For detailed information on this camera, please refer to the
Series Fixed Mini Dome Network Camera Reference Guide
your CD.
Before installing the camera, Honeywell recommends that you check
www.honeywellvideo.com/products/cameras/
and download the latest manuals and software updates.
Warnings
Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain
your warranty.
WARNING!
12 VDC/24 VAC models require the use of CSA
Certified/UL Listed Class 2 power adapters to ensure
compliance with electrical safety standards. Power
over Ethernet (PoE) should meet the IEEE 802.3 af
PoE standard.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
WEEE (Waste Electrical and Electronic Equipment). Correct
disposal of this product (applicable in the European Union and
other European countries with separate collection systems).
This product should be disposed of, at the end of its useful life,
as per applicable local laws, regulations, and procedures.
FCC Compliance
Information to the User: This equipment has been tested and found to comply
with the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules,
these limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference. For example, try reorienting
or relocating the receiving antenna, increasing the separation between the
equipment and receiver, or connecting the equipment to an outlet on a different
circuit.
Caution
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2
No. 60950-1.
Europe
The manufacturer declares that the equipment supplied with this guide is
compliant with the essential protection requirements of the EMC directive 89/
336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the
requirements of standards EN 55013 for emissions, EN 50130-4 for immunity,
and EN 60950 for Electrical Equipment safety.
Document 800-01741 – Rev B – 08/08
Unpack Everything
•
•
You may also require a drill, screwdrivers and side-cutters.
Installation
1.
2.
EQUIP™
located on
to find your camera
3.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
4.
5.
6.
7.
Connect the Wiring
Power, Network, and Video
Caution
one type of power supply (PoE IEEE 802.3 Ethernet or 12 VDC or 24
VAC power plug) at the same time.
HD4DIP/X Camera
This guide
Use the mounting template to mark and pre-drill the holes.
Remove the gimbal from the enclosure base so you can easily
access the mounting holes (see illustration below).
a.
Squeeze the 4 black
tabs until they are
free of the black
clips.
b.
Elevate the hinge
until the gimbal is
above the housing
and you have
access to the
camera board
connections and
mounting holes.
Install the conduit plug
into the unused conduit
entry (see illustration
below). The HD4DIP
comes with the conduit
plug pre-installed in the
conduit entry on the
back of the housing. This
plug may be removed
and installed in the side
conduit entry.
Connect the cables through the back or side conduit entries.
See
Connect the Wiring
below.
Mount the camera to a wall or ceiling using the supplied screws.
To prevent moisture from entering housing:
Position the enclosure with the conduit pointing down. Apply
sealant around the conduit connection and mounting screws.
Replace the gimbal by reinserting the black tabs into the black
clips before installing the dome enclosure.
Cabling (side or back)
To avoid damage to the camera, never connect more than
•
Mounting template
•
Hardware kit
Black tabs (x4)
Metal
hinge
Mounting
holes
Black clips (x4)
Back entry conduit
Side entry conduit
Conduit plug
Power (12 VDC/24
VAC)
BNC video out (see
Adjust the Field of
page
2)
Audio/Alarms (see
Audio and
Alarms,
page
2)
RJ45 Ethernet network
connection (using
10Base T or 100Base
TX cable). Also for
Power over Ethernet
(PoE 802.3 af).
View,
Advertisement
Related Manuals for Honeywell EQUIP Series
Summary of Contents for Honeywell EQUIP Series
-
Page 1: Unpack Everything
This guide • Hardware kit You may also require a drill, screwdrivers and side-cutters. Thank you for purchasing a Honeywell EQUIP Series Fixed Mini Dome Network Camera. Before installing the camera, please verify your Installation model and read this guide carefully: HD4DIP, NTSC, 2.8 - 10 mm Vari-focal Auto Iris lens... -
Page 2: Network Setup
Document 800-01741 – Rev B – 08/08 © 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.