hit counter script
Canon iR2200 Service Manual
Hide thumbs Also See for iR2200:
Table of Contents

Advertisement

iR2200/iR2800/
iR3300
REVISION 0
FY8-13H8-000
MAR. 2001
COPYRIGHT© 2001 CANON INC.
CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)

Advertisement

Table of Contents
loading

Summary of Contents for Canon iR2200

  • Page 1 REVISION 0 FY8-13H8-000 MAR. 2001 COPYRIGHT© 2001 CANON INC. CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
  • Page 2 Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality.
  • Page 3 Provides a description of a service mode. Provides a description of the nature of an error indication. Refers to the Copier Basics Series for a better understanding of the contents. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 4: Outline Of The Manual

    INTRODUCTION 2 Outline of the Manual This Service Manual contains basic information needed to service the iR2200/iR2800/ iR3300 and its accessories (i.e., side paper deck, shift tray) in the field, conducted for the purpose of maintaining its product quality and a specific level of performance. A separate Service Manual is made available for each of its accessories (except for the side paper deck and shift tray);...
  • Page 5 All service persons are expected to familiarize themselves with the contents of this Ser- vice Manual and Service Information bulletins and acquire a level of knowledge and skill required to promptly respond to the needs of the field. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 6 All service persons are expected to have a good understanding of the contents of this Ser- vice Manual and all relevant Service Information bulletins and be able to identify and isolate faults in the machine. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 7 SYSTEM UNIT COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 9: Table Of Contents

    Editing ........ 2-8S 4.2 Power Supply Modes ..... 2-15S 2.2.5 Density Conversion 4.3 Standby Mode (LUT) ......... 2-8S (normal operation) ....2-15S 4.4 Sleep Mode 1 ......2-15S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 10 Installing the Card Reader-C1 ..3-23S Connection ......3-18S Installing the Document 2.11.1 Using the PING Tray-D2 ........3-26S Function ......3-18S Replacing the Drum Unit ....3-27S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 11: Chapter 1 General Description

    CHAPTER 1 GENERAL DESCRIPTION COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 13: Specifications

    Dual process method (about 50 sheets of 80 g/m paper) Transfer Roller Separation Static eliminator (static separation) + curvature Cleaning Blade Fixing SURF method (plane heater and fixing film) T01-101-02 1-1 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 14: Functions

    • Transparency (Canon-recommended):A4, A4R, LTR, LTRR • Colored paper (Canon-recommended):B4, A4, A4R • Postcard: Jpn (vertical feed), double-card, 4-sheet card • Label sheet (Canon-recommended):B4, A4, A4R, LTR, LTRR • Thick paper (90 to 128 g/m ):A3, B4, A4, B5, A4R, B5R, LTR, LTRR •...
  • Page 15 • Transparency (Canon-recommended)A4, A4R, LTR, LTRR • Colored paper (Canon-recommended):B4, A4, A4R • Postcard: Jpn postcard (vertical feed), double-card, 4-sheet card • Label sheet (Canon-recommended):B4, A4, A4R, LTR, LTRR • Thick paper (90 to 128 g/m ):A3, B4, A4, B5, A4R, B5R, LTR, LTRR •...
  • Page 16 • Token Ring Network Interface Adapter iN-TR2 *1:The values within parentheses indicate when the DADF is used. T01-101-05 The above specifications are subject to change for product improvement. 1-4 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 17: Others

    720 W (approx.; reference only) Noise Sound power level (Impulse mode) Copying iR2200: 66 dB or less, iR3300: 71 dB or less Standby iR2200: 40 dB or less, iR3300: 50 dB or less Ozone 0.01 ppm or less avg., 0.02 ppm or less max.
  • Page 18 A4R → B4 A5 → B5 I (115.4%) B4 → A3 B5 → A4 Delivery by copier, Auto paper select ON, Auto density, Non-sort, Cassette T01-101-07 1-6 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 19 *STMTR cannot be used as an original. Delivery by copier, Auto paper select ON, Auto density, Non-sort, Cassette T01-101-08 The above specifications are subject to change for product improvement. 1-7 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 20: Side Paper Deck-L1

    None (DC power supplied by accessories power supply of host machine) Operating conditions Same as host machine T01-102-01 The above specifications are subject to change for product improvement. 1-8 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 21: Names Of Parts

    [5] Cassette 1 [13] Extension board slot [6] Cassette 2 [14] Main power switch [7] Delivery tray [15] Cassette heater switch [8] Multifeeder F01-201-01 1-9 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 22 [3] Left cover [6] Feeding assembly releasing lever [4] Left lower rear cover (waste toner [7] Duplex feeding assembly releas- case cover) ing lever F01-201-02 1-10 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 23: Cross Section

    [32] [35] [19] [34] [17] [30] [37] [33] [18] [31] [14] [24] [21] [25] [26] [20] [27] [36] [28] [16] [29] [23] [22] F01-202-01 1-11 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 24 [16] Transfer guide [35] Delivery roller [17] Multifeeder pickup roller [36] Duplexing roller [18] Multifeeder separation pad [37] Reversing frapper [19] Registration roller T01-202-01 1-12 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 25: System Configuration

    Image Formation Block Feeding Delivery Pickup Multi- tray control feeder Duplexing assembly Side paper deck Cassette 1 (accessory) Cassette 2 Pickup/Feeding Block F01-301-01 1-13 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 26: Outline Of The Electrical

    PCB • Sensor • Fan LAMP1 • Etc. Inverter Finisher (IC309) (accessory) DC controller Accessories Main Composite power power power supply supply supply F01-302-01 1-14 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 27 J401 J204 Scanner motor M400 J402 Switch Inverter J4021 Note: The in the diagram indicates connection between PCBs, NOT the flow of signals. F01-303-01 1-15 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 28 [2] Platen Cover TypeE [7] Finisher-J1 [3] Document Tray-D2 [8] Inner 2way Tray-A1 [4] Copy Tray-F1 [9] Paper Deck-L1 [5] Saddle Finisher-G1 [10] Cassette Feeding Unit-W1 F01-304-01 1-16 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 29 Adapter iN-TR2 TokenRing Riser TokenRing network Super G3 FAX Board-J1 PSEUDO Public SPEAKER telephone UNIT UNIT network UNIT MODEM Super G3 FAX Expansion Kit-B1 F01-304-02 1-17 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 31: Chapter 2 Main Controller

    CHAPTER 2 MAIN CONTROLLER COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 33: Basic Construction

    The machine may broadly be divided in to the following functional blocks, with the con- troller block covering the shaded area: Reader unit Control panel Controller unit Accessory Main controller PCB boards Printer unit F02-101-01 2-1 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 34: Outline Of The Electrical Circuitry

    • Stores the boot program. T02-102-01 1.2.3 HDD Item Description • Sores the system software. • Stores image data for the Box function. T02-102-02 2-2 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 35 CHAPTER 2 MAIN CONTROLLER Reader unit Accessory Control panel boards DIMM-ROM Main controller PCB Printer unit F02-102-01 2-3 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 36: Start-Up Sequence

    CPU reads the system software from the HDD to the SDRAM, and the progressive bar on the screen indicates the progress of the start-up sequence. Start-Up Screen Wait… Progressive bar F02-103-01 2-4 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 37: Start-Up Sequence

    F02-103-02 E601-0000, 0001 Indicates the presence of an error in image transfer information. E602-0001, 0002 Indicates the presence of an error in write/read operation. 2-5 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 38 System area area Boot Self-diagnostic program program Boot ROM Main controller PCB access to the program during execution. flow of the system program. F02-103-03 2-6 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 39: Digital Image Processing

    Compression/de-compression, rotation, enlargement/reduction Image memory SDRAM control I/O control Printer PG Image server Binary-binary processing density conversion Smoothing 4 or 2 Printer unit F02-201-01 2-7 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 40: Input Image Processing

    Density Correction (γ γ γ γ γ conversion) The γ conversion table best suited to each specific mode (test, text/photo, print photo, film photo) is used to correct density. 2-8 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 41: Compression/De-Compression

    The image data subjected to image memory control is temporarily stored in SDRAM. 2.3.3 HDD The HDD functioning as an image server is used to store image data for the Box function. 2-9 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 42: Output Image Processing

    600×600 dpi is converted into 2400*×600 dpi. *Equivalent. 2.4.2 Binary-Binary Density Conversion (read image output only) This processing is used as an auxiliary means for adjusting the density of images. 2-10 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 43: Soft Counters

    Sensor used Delivery slot Single-sided Inlet sensor Finisher delivery tray Double-sided 1st side PS18 Double-sided outlet sensor 2nd side Inlet sensor Finisher delivery tray T02-301-01 2-11 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 44 The following diagrams show the locations of the sensor in the finisher and the saddle fin- isher: Inlet sensor(S2) F02-301-01 Inlet sensor (PI1) F02-301-02 2-12 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 45 *2:The counter description may be changed or enabled/disabled for display in service mode (except counter 1, whose setting cannot be cannot be changed). T02-301-03 2-13 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 46 OPTION>USER>COUNTER6 Use it to enable or disable the display of soft counter 6 in the control panel, or to change the counter type. 2-14 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 47: Controlling The Power Supply

    4.4 Sleep Mode 1 In sleep mode 1, only the LCD image desplay remains OFF. 2-15 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 48: Shift From Sleep Mode 1 To Standby Mode

    A shift from sleep mode 1 to standby mode is expected for the following: • The power switch (soft switch) in the control panel is turned on. 2-16 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 49: Shift From Sleep Mode 2 To Standby Mode

    The power is turned off when the main power switch is turned off. A shift from this state may be made only by turning on the main power switch; the shift will be automatic and to standby mode. 2-17 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 50: New Functions

    Binary data (10) job n PDL data Print image processing block Binary data (11) Network PCB Image date (12) PDL data Printer unit F02-501-01 2-18 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 51: Smb Printing

    IP address of the machine before it sends a print job to the machine. WINS server Ethernet iR2200 Protocol:TCP/IP iR2800 Service:SMB iR3300 Windows 95/98 Windows 95/98 F02-502-01 2-19 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 52 When OPD printing is selected, the following job information will be printed: LPD Banner (sample) iR2200-3300 (iN-E2) USER NAME : ts HOST NAME : canon JOB NAME : golfer.ps F02-503-01 2-20 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 53: Chapter 3 Installation

    CHAPTER 3 INSTALLATION COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 55: Selecting The Site Of Installation

    5. The floor of the site must be level so that the feet of the machine will remain in contact and the machine itself will remain level. 3-1 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 56 110 cm min. 100 cm min. F03-100-02 7. The site must be well ventilated. Do not install the machine near the air inlet of the room. 3-2 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 57: Unpacking And Installation

    2. The machine weighs about 80 kg. Be sure to work in a group of four. 3-3 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 58: Unpacking And Removing The Fixing Materials

    (weight of body: about 80kg) Take care so that the main power switch will not be turned on when the machine is lifted. 3-4 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 59 Cassette size label (inside cassettes) • Cassette size plate (inside cassette) • Guidebook (model w/ printer function only) • CD-ROM (model w/ printer function only) 3-5 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 60: Mounting The Scanner

    2) Shift down the feeder releasing lever [1] to release the feeding assembly. 3) Turn the developing assembly locking lever [2] counterclockwise to free the developing assembly. 3-6 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 61: Supplying The Toner

    2.5 Supplying the Toner Work Checks/remarks 1) Holding the grip [1] of the developing assembly, pull the developing assembly [2] to the front until it stops. 3-7 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 62 (where the marking STOP is found). 5) Tap lightly on the top of the toner car- tridge so that all toner will drop. 3-8 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 63 The toner cartridge will become disen- gaged. 7) Remove the toner cartridge. 8) Push in the developing assembly until it butts against the rear. 3-9 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 64: Mounting The Drum Unit

    [2]. At this time, take full care not to bring the developing assembly in contact with the developing cylinder, which is situ- ated nearby. 3-10 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 65 Do not turn on the main power switch while the feeding assem- bly remains released; otherwise, the fixing assembly will be damaged. 7) Close the front cover. 3-11 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 66: Stirring The Toner

    Function Option Test Counter <INSTALL > < 1/ 1 > <NO-PAPER> TONER-S Check the Developer STRD-POS 0 →( CARD 0) { 1 - 2700} 3-12 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 67: Setting The Cassette

    2) Check with the user to find out the size of paper to use, and check the size set- ting (A/B or Inch) using the selection switch [1] of each cassette. 3-13 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 68 The middle cassette cannot hold A3 or 11×17 paper. 4) Set the paper size dial to suit the se- lected paper size. Set the dial as indicated. 3-14 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 69 [1], and fit the cassette size plate to each cassette. 6) Put paper into the cassettes [3], and slide them into the machine. 3-15 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 70: Checking The Images/Operations

    • Make copies in multiple sets, and check to make sure that copies are made specified numbers. 3-16 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 71 7) Clean the area around the machine, and fill out the Service Book. 3-17 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 72: Connecting To The Network

    IP address input Results (OK/NG) 3) Press the Start key. • If PING is successful, ‘OK’ will be in- dicated: otherwise, ‘NG’ will be indi- cated. 3-18 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 73: Making A Check Using A Remote Host Address

    If the connection is correct, go to 2.12.2. • If the connection is wrong, correct it, and make a check once again using the remote host address. 3-19 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 74: Making A Check Using A Loop-Back Address

    • If ‘OK’ is indicated, suspect a problem in the user’s network environment; report to the user’s system administrator, and ask for corrective measures. 3-20 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 75: Relocating The Machine

    4) Place a single sheet of A3/11×17 paper on the copyboard glass, and tape the copyboard cover (ADF) in place. 3-21 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 76: Lifting The Machine Off The Pedestal

    (pay attention to the pins of the pedestal). 5) Place the machine on the floor or on a desk. 3-22 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 77: Installing The Card Reader-C1

    4) Open the manual feed tray and the right lower cover. 5) Remove the five screws [1] ; and, while opening the right rear cover [2] slightly, detach the right rear cover. 3-23 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 78 8) Connect the connector [2] on the card reader [1] side and the connector [2] on the machine side. 3-24 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 79 [3] and a washer [4]. Take care not to trap the con- nector or the harness. 3-25 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 80: Installing The Document Tray-D2

    2. The document tray may be mounted to the left side of the machine. 3-26 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 81: Replacing The Drum Unit

    4. When removing the tape from the rear end of the drum unit, keep the rear end higher than the front cover to prevent spilling waste toner. 3-27 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 82 8) Secure the new drum unit in place using the fixing screw you removed in a pre- vious step. Screw Drum unit 3-28 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 83 14) Mount the paper lint cleaning cover. 15) Close the front cover. 16) Turn on the main power switch. 3-29 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 84 The machine ends APVC correction by delivering a blank sheet. 20) Press the Reset key twice to end service mode. 21) Turn off the main power switch. 3-30 S COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 85 READER UNIT COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 87 Drive Cable ..... 2-21R 3.1 Outline ........2-9R 5.2.5 Adjusting the Position of the 3.2 Scanning Lamp ......2-9R No. 1/No. 2 Mirror Base .. 2-22R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 88 3.4 Related Service Mode ....3-8R Controller PCB ....3-16R Disassembly and Assembly ... 3-9R 4.4.2 When Replacing the 4.1 External Covers ..... 3-10R Reader Controller PCB ... 3-16R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 89: Chapter 1 Basic Operation

    CHAPTER 1 BASIC OPERATION COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 91: Outline Of Electrical Circuitry

    T01-102-01 List of Control Items Inverter (IC400) LAMP1 Controller unit (IC401) Scanner M400 motor (IC402) Printer unit EEPROM (IC403) (IC404) Reader controller PCB F01-102-01 Major PCBs 1-1 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 92: Basic Sequence Of Operations

    While the scanner is moving in reverse. STBY(standby) From when shading correction ends to when the Start key is turned on or when the power switch is turned off. T01-202-01 1-2 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 93 3 Inputs to and Outputs from the Major PCBs 3.1 Wiring of Major PCBs J409 Controller controller unit Reader controller J408/J407/J403 CCD PCB J601/J600/J602 J402 Inverter PCB J4021 F01-301-01 1-3 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 95: Chapter 2 Original Exposure System

    CHAPTER 2 ORIGINAL EXPOSURE SYSTEM COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 97: Outline Of Operations

    [1] In book mode, by a reflection type sensor in sub scan- ning direction; by a CCD in main scanning direction. [2] With the ADF in use, by the ADF. 2-1 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 98 Photointerrupter (detects the state (open/closed) of sensor copyboard cover) [5] No.1 mirror base No. 1 mirror [6] No.2 mirror base No. 2/No. 3 mirror 2-2 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 99: Sequence Of Operations (Original Exposure)

    (at the speed used for 50% reduction). 6. The scanner moves to home position and remains in wait. : No. 1 mirror position. F02-102-02 2-3 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 100: Copyboard Cover Open

    (at the speed used for 50% reduction). 6. The scanner moves to the point of original size : No. 1 mirror base detection. F02-102-04 2-4 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 101: Enlargement/Reduction (Zoom)

    [4] For an enlargement between 401% and 800%, image data read at 200% to 400% is sub-jected to repeating (doubling) in the main controller assembly. 2-5 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 102: Scanner Drive System

    [4] Reader controller PCB [5] No.1 mirror base [6] Scanner motor [7] Scanner HP sensor [8] Copyboard cover sensor [9] Light-blocking plate [10] No.2 mirror base 2-6 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 103: Controlling The Scanner Motor

    [3] Image read. Used to read the image at a specific speed suited to the read ratio. [4] Deceleration. Used to enable the scanner to speed down and stop promptly, starting at the end of the image. F02-202-02 2-7 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 104: Reversing The Scanner After Scanning In Main Reading Direction

    Shading position Vertical size plate Vertical size plate Copyboard glass Copyboard glass Standard white plate Standard white plate Decrease Increase Decrease Increase F02-202-03 F02-202-04 2-8 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 105: Controlling The Scanning Lamp (La2)

    CPU on the reader controller PCB. When the signal is generated, the inverter generates a high-frequency voltage using the drive voltage (+24 V) supplied by the reader controller PCB to turn on the xenon tube. 2-9 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 106: Detecting An Error

    It is used to indicate a fault in the inverter PCB. E225 It is used to indicate a fault in the scanning lamp (xenon tube). 2-10 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 107: Detecting The Size Of Originals

    The combination of these output measurements is used to identify the size of the origi- nal. For specific movements, see the pages that follow. 2-11 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 108: Outline Of Detection Operation

    The machine will identify the size of an original based on the combination of the results (T02-404-01) 2-12 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 109: Book Mode, 1 Original, Copyboard Cover Close

    (external light) and the absence of an original is identified, excluding B5, B4, A4, and A3. 2-13 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 110 Originals Original Originals Point of CCD detection Original size sensor size sensor 11"* 17" LTRR None : Changes : Does not changes None T02-404-02 2-14 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 111: Disassembly And Assembly

    5. As a rule, the machine must not be operated with any of its parts removed. 2-15 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 112: Exposure Lamp

    [1] together with the cable fixing plate [5]. F02-501-01 5) Remove the screw [1], and detach the connector cover [2] found at the rear. F02-501-02 2-16 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 113: After Replacing The Scanning Lamp

    CCD adjust- ment data on the service label. 1.COPIER>FUNCTION> CCD>CCD-ADJ CCD Auto Adjust 2. All items under COPIER>ADJUST>CCD. CCD Adjustment Data 2-17 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 114: Scanner Drive Assembly

    5) Detach the belt, and remove the motor unit [2]. F02-502-02 6) Remove the two screws [1], and detach the scanner motor [3] from the motor mounting plate [2]. F02-502-03 2-18 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 115 F02-502-05 6) Tighten the two screws to secure the motor unit in place. 2-19 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 116: Removing The Scanner Drive Cable

    3) Remove the spring [3] used to secure the cable in place. 4) Remove the cable fixing plate [4], and free the cable [5] from the pulleys. F02-502-06 2-20 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 117: Routing The Scanner Drive Cable

    4) Temporarily secure the cable fixing in place to the No. 1 mirror base. (Do not tighten the screw fully.) 5) Fit the reader upper frame. 6) Adjust the position of the No. 1 and No. 2 mirror bases. F02-502-07 2-21 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 118: Adjusting The Position Of The No. 1/No. 2 Mirror Base

    • For the Front (F marking) (initial; FY9-3009) (set for the machine) F02-502-08 • For the Rear (R marking) (initial; FY9-3009) (set for the machine) F02-502-09 2-22 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 119 5) Fully tighten the screw on the cable fix- ing so that it is secured on the No. 1 mirror base. 6) Detach the mirror positioning tool (2 pc.). 2-23 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 120: Sensors

    2) Remove the left support cover. 3) Remove the two harness bands [1]. 4) Remove the screw [1], and detach the sensor mounting plate [2]. F02-503-03 2-24 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 121 2) Disconnect the connector [1]. 3) Remove the screw [2], and detach the copyboard sensor cover [3]. 4) Remove the copyboard cover sensor [4]. F02-503-05 2-25 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 122 [2]. F02-504-03 5) Disconnect the connector [1]. 6) Remove the two screws [2], and slide out the inverter PCB [3]. F02-504-04 2-26 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 123: Chapter 3 Image Processing System

    CHAPTER 3 IMAGE PROCESSING SYSTEM COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 125: Outline

    [1] CCD/AP PCB. Drives the CCD, performs analog image processing, performs A/D conversion. [2] Reader controller PCB. Performs shading correction, performs auto density adjustment (AE). 3-1 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 126: Analog Image Processing

    Output buffer Odd-number pixel data Shift register Gate Light receiving segment (photodiode) Gate Even-number pixel data Shift register Output buffer F03-202-01 CCD Block Diagram 3-2 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 127: Gain Correction And Offset Correction Of The Ccd Output 3-3R

    Range: 0 to 400 (A change by ‘1’ results in a shift of 0.1 mm.) Decrease Read start position Increase Original Vertical size plate F03-205-01 3-3 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 128: Digital Image Processing

    To make up for the fluctuations in the intensity of light occurring at short intervals, edge area gain correction is also executed. 3-4 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 129: Shading Adjustment

    CCD pixels, thereby ensuring a specific level of image density. CCD output Characteristics after correction Characteristics Target value before correction Results of measurement White Original density Standard white plate F03-302-01 3-5 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 130: Edge Gain Correction (Adf In Use)

    Edge gain correction plate 1 pixel Copyboard glass Main scanning direction Reading glass 7450 pixels Standard white plate (for shading) F03-302-02 3-6 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 131: Auto Density Adjustment (Ae)

    White Background Original Colored Original Surface of original (white) Output level (white) (black) (black) dynamic range of white-background original. dynamic range of colored-background original. F03-303-01 3-7 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 132: Related Service Mode

    (for real-time AE mode; 10 steps). Range: 0 to 9 (default: 4) Copy density White Lower setting Higher setting decreases text density increases text density White Original density F03-304-01 3-8 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 133: Disassembly And Assembly

    5. As a rule, the machine must not be operated with any of its parts removed. 3-9 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 134: External Covers

    [2]. When mounting the reader right cover [2], loosen the top screw [4] of the right rear cover [3] first. F03-401-02 3-10 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 135: After Mounting The

    COPIER>FUNCTION>CCD> SH-PS-ST Use it to execute optimum posi- tion auto adjustment for the standard white plate. 3-11 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 136: Removing The Ccd Unit . 3-12R

    4) Shift the CCD unit [4] to the left. F03-402-01 5) Disconnect the three connectors [1], and detach the CCD unit [2]. F03-402-02 3-12 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 137: Points To Note When

    CCD adjustment data on the service label. 1) COPIER>FUNCTION> CCD>CCD-ADJ CCD Auto Adjustment 2) COPIER>FUNCTION> CCD>EGGN-POS Edge Gain Correction Auto Adjustment 3) all items under COPIER>ADJUST>CCD CCD Adjustment Data 3-13 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 138: Frames

    2) Remove the two screws [1] from the top face. 3) Remove the 15 screws [2] from the side face. 4) Remove the reader upper frame [3]. F03-403-02 3-14 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 139: Mounting The Reader Upper Frame

    2) Fit the eight screws [5] of the claw as- sembly first. 3) Fit the seven screws [6] of the side. 4) Lastly, fit the two screws [7] on the top face. F03-403-03 3-15 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 140: Pcbs

    4.4.2 When Replacing the Reader Controller PCB See “Troubleshooting”>Chapter 4 “Troubleshooting Image Faults/Malfunctions” >6.7 “Variable Resistors (VR), Light-Emitting Diodes, and Check Pins by PCB” 3-16 R COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 141 PRINTER UNIT COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 143 1.2 Basic Sequence of Operations 2.1 Outline ........4-4P (image formation system) ..4-3P 2.2 Turning On/Off the Bias ... 4-5P 2.2.1 DC Bias ......4-5P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 144 Removing the Blade 6.1 Outline ........4-17P Base Unit ......4-35P Developing Assembly ....4-18P 9.5.6 Removing the 7.1 Outline ........4-18P Developing Cylinder ..4-35P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 145 3.6 Moving Up/Down the Roller ..........5-29P Pickup Roller ......5-15P 6.1 Outline ........5-29P 3.7 Pickup Retry Operation ..5-16P 6.2 Control System ....... 5-29P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 146 Removing the Riser Controlling the Fixing Temperature 6-6P Guide ....... 6-12P 3.1 Outline ........6-6P 4.1.3 Removing the Fixing 3.2 Temperature Control ....6-7P Assembly ......6-13P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 147 5.3.12 Removing the Accessories Cover ....... 7-14P Power Supply ....7-21P 5.1.3 Removing the Support 5.3.13 Removing the Main Cover ....... 7-15P Power Supply ....7-22P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 148 Removing the Right Pickup Roller ....8-38P Cover ....... 8-21P 3.4.4 Removing the Deck 3.1.5 Removing the Front Pickup/Feeding Roller ..8-38P Upper Cover ....8-21P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 149 Main Motor ...... 9-16P 4.1 Identifying the Size ....9-8P 5.4.3 Mounting the Pedestal 4.2 AB/Inch-Setting Switch ... 9-8P Main Motor ...... 9-17P 4.3 Paper Size ......... 9-8P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 150 5.2.1 Replacing the Spring ..11-7P Detecting Jams ......11-6P 5.3 Changing the Size ....11-8P 2.1 Outline ........11-6P 5.3.1 Changing the Size .... 11-8P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 151: Chapter 1 Introduction

    CHAPTER 1 INTRODUCTION COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 153: Safety

    The following is the label that indicates compliance with the CDRH ordinances, and it must be found on all laser products sold in the US. 1-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 154 CHAPTER 1 INTRODUCTION F01-102-01 CDRH Label The description may vary from model to model. 1-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 155: Handling The Laser System

    Take full care whenever servicing areas of the machine behind these covers. This label is attached to all covers inside the machine where hazards from laser light exist. F01-103-01 Laser Warning Label 1-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 156: Safety Of Toner

    In addition, avoid bringing toner into contact with plastic material, as it tends to dissolve easily. Do not throw toner into fire to avoid explosion. 1-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 157 [3] Laser scanner unit [9] Pickup (deck/cassette) [4] Primary charging roller [10]Transfer roller [5] Developing cylinder [11]Static eliminator [6] Pre-transfer roller [12]Cleaner assembly (drum unit) [13]Fixing assembly 1-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 158 4. Development 8. Drum cleaning Manual feed tray 5. Transfer Registration Delivery 6. Separation 7. Fixing Deck/cassette flow of paper. direction of drum rotation. F01-201-02 1-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 159: Chapter 2 Sequence Of Operations

    CHAPTER 2 SEQUENCE OF OPERATIONS COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 161: Basic Operations

    Image Formation Block Feeding Delivery Pickup Multi- tray control feeder Duplexing assembly Side paper deck Cassette 1 (accessory) Cassette 2 Pickup/Feeding Block F02-101-01 2-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 162: Outline For The Electrical Circuitry

    • Motor (IC303) supply PCB • Sensor • Fan • Etc. Accessories power supply PCB Finisher (IC309) (accessory) Composite power DC controller supply PCB F02-102-01 2-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 163: Basic Sequence Of Operations

    Power switch ON INTR STBY Fixing moter (M4) Main motor (M1) Scanning lamp (LAMP1) *1: The scanning lamp goes OFF at the end of shading. T02-103-01 2-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 164 Keeps the machine at rest from when WUP3 ends to the Start key is pressed or until the power switch is turned off. T02-103-01 2-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 165 PCB (M1) Clock pulse J308 J3086 MM_LOCK generation circuit MM_ON Control DC controller circuit Reference signal gene- ration circuit F02-104-01 Control Circuit Block Diagram 2-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 166 J3114 J1015 Conposit J301 power supply J136 J1014 J111 J409 J201 J308 Main J205 power J300 supply Reader J204 controller Switch F02-105-01 2-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 167: Chapter 3 Laser Exposure System

    CHAPTER 3 LASER EXPOSURE SYSTEM COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 169: Outline Of Operations

    Main scanning direction: control by BD signal Sub scanning direction: control by image leading edge signal Laser scanner motor control Constant speed rotation control T03-101-01 3-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 170 Polygon mirror 6-faceted BD mirror/BD PCB Laser beam detection Laser driver PCB Laser activation control DC controller PCB Laser scanner motor rotation control T03-101-02 3-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 171: Sequence Of Operations (Laser Exposure System)

    BD signal so that the image will be placed at a specific position on the paper without fail. 3-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 172: Flow Of Sync Signals

    Controller assembly F03-202-01 E100 Indicates that the BD signal cannot be detected within a specific period of time after the laser has been turned on. 3-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 173: Laser Driver Circuit

    (PS11). 3-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 174 Use it to adjust the position of laser illumination. ADJUST>LASER>LA-OFF Use it to adjust the timing of laser trailing edge de-activation for non-de- fault size papers. 3-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 175: Controlling The Laser Scanner Motor

    Main power generation supply PCB circuit Laser scanner J204 motor F03-401-01 E110 Indicates the presence of an error in the laser scanner motor. 3-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 176 Leakage of laser light must be avoided, as it can adversely affect the human body. Do not disassemble parts not discussed herein or remove any paint-locked screws. 3-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 177: Laser Scanner Assembly

    F03-501-02 When mounting the Finisher-J1, attach the protective sheet [2] by aligning it against the press line [1] of the laser unit. F03-501-03 3-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 179: Chapter 4 Image Formation System

    CHAPTER 4 IMAGE FORMATION SYSTEM COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 181: Outline Of Processes

    Transfer guide bias control DC constant voltage (-600 v) Separation static eliminating DC constant voltage (switching between -2.3 KV and -3.0 KV) bias control T04-101-01 4-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 182 F04-101-01 shows the major components of the image formation system: Primary charging roller Pre-exposure lamp Developing assembly Cleaner unit Photosensitive drum Separation static eliminator Transfer guide Transfer charging roller F04-101-01 4-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 183: Basic Sequence Of Operations (Image Formation System)

    Transfer guide bias Separation static eliminating bias [1] transfer charging cleaning bias [2] transfer sheet-to-sheet interval bias [3] transfer charging reference bias(each 1000sheets, cumulative) F04-102-01 4-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 184: Controlling The Primary Charging Roller Bias

    F04-201-01 The primary charging output enable signal is used as the AC pulse ON sig- nal when the developing bias is being controlled. Memo 4-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 185: Ac Bias

    AC bias output control signal as needed to drive the transformer. [2] The AC bias is made to assume a specific current level. 4-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 186: Temperature Correction Of The Dc Bias

    Counter reading: 0 to 10,000 sheets Counter reading: 10,001 or higher 2300µA 2150µA 2000µA High High Humidity Humidity F04-205-01 4-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 187: Controlling The Detection Of The Photosensitive Drum Resistance (Apvc Control)

    PW-CPU. If you have replaced the drum unit with a new one, be sure to execute the following service mode: COPIER>FUNCTION>DPC>D-GAMMA. 4-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 188 Use it to enter the adjustment value of primary charging AC component for the image area. COPIER>FUNCTION>DPC>D-GAMMA Use it to force photosensitive drum resistance measurement control (APVC). 4-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 189: Controlling The Transfer Charging Roller Bias

    2 Current Drive detection control Environment sensor (humidity) Transfer bias output Transfer output current switching signal mode signal 3 J302-B14 Measurement result F04-301-01 4-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 190: Turning On/Off The Bias

    [2] The transfer charging mechanism operate using the voltage level determined by the PW- CPU. If you have replaced the transfer charging roller with a new one, be sure to execute 'clean roller' in user mode ('adjust/clean'). 4-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 191: Controlling The Output By Operating Mode

    E064 Indicates the presence of a high-voltage (primary charging, transfer charg- ing, development) output fault. 4-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 192: Turning On/Off The Cleaning Bias

    When the cleaning bias output ON signal (composite power supply PCB) goes ‘1’, the output of the transfer cleaning bias transformer is applied to the transfer charging roller. 4-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 193: Controlling The Output

    Use it to enter the output adjustment value for transfer charging (special pa- per; single-sided print and double-sided print) COPIER>OPTION>BODY>TRANS-SW Use it to set the transfer charging roller bias output control method for large-size paper. 4-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 194: Controlling The Separation Static Eliminator Bias

    ON signal level Serial communication control Print/standby mode signal Static eliminator bias Static eliminator bias mode signal mode signal J301 J136 -A10 -A12 F04-401-01 4-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 195: Turning On/Off The Bias

    The selection of an application voltage is done in response to the static eliminator bias mode signal (serial communication) from the DC controller PCB. 4-15 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 196: Controlling The Transfer Guide Bias

    Serial communication Photosensitive Transfer Transformer drum guide output High-voltage drive signal Print/standby mode signal main transformer J131-3 (T504) Transfer guide J301 J136 -A10 -A12 F04-501-01 4-16 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 197: Primary Charging Roller Cleaning Mechanism

    SL6 (ON) Back-and-forth movement Primary charging roller Cleaning pad Photosensitive drum F04-601-01 4-17 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 198: Developing Assembly

    Developing bias J301 J136 J130-1 Photosensitive drum Toner sensor(S1) Main Developing motor clutch Main motor drive signal J308 Toner detention signal J302-5 F04-701-01 4-18 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 199: Controlling The Developing Bias

    ON signal -B11 F04-702-01 The AC pulse ON signal is used as the primary charging output enable sig- nal when controlling primary charging. Memo 4-19 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 200: Controlling The Dc Developing Bias

    Use it to enter the adjustment value of the developing bias DC component for the image area. COPIER>ADJUST>DEVELOP>DE-OFST Use it to enter the offset value for the developing bias DC component. 4-20 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 201: Detecting The Level Of Toner

    6 sec to check the presence of toner; if toner is found, recovery is made. If toner is not found, the Add Toner message will be indicated. F04-703-01 4-21 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 202: Drum Cleaner

    Waste toner feedscrew Waste toner case full sensor (S2) Main motor Waste toner case J311-B9 J308 DC controller PCB F04-801-01 4-22 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 203 Waste toner case Cleaning blade full sensor (S2; light-receiving) Photosensitive drum Waste toner case full sensor (S2; light-emitting) Waste toner feedscrew Waste toner case F04-801-02 4-23 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 204: Monitoring The Waste Toner Case

    DC controller PCB Waste toner case J311-B7 full sensor Waste toner case full signal (light-receiving) Waste toner case full sensor (light-emitting) Waste toner case F04-802-01 4-24 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 205: Locking Of The Waste Toner Feedscrew

    The machine is not equipped with a sensor to detect the locking of the waste toner feedscrew. Memo Photosensitive drum Main motor Spring Coupling Waste toner feedscrew F04-803-01 4-25 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 206: Disassembly And Assembly

    6. The door switch or the main power switch must be turned off whenever the duplex unit or the fixing/feeding unit must be slid out. The toner must not be disposed of into fire to avid explosion. 4-26 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 207: Pre-Exposure Lamp Unit

    -2) Remove the inside cover. (p. 7-14P) 3) Disconnect the connector [1], and re- move the screw [2]. 4) Remove the pre-exposure lamp unit [3]. F04-901-01 4-27 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 208: Photosensitive Drum

    Take care when deciding where and how to place the drum unit after tak- ing it out of the machine. F04-902-03 4-28 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 209: Cleaning The Photosensitive Drum

    (Do not use paper, lint-free or otherwise.) Do not dry wipe it nor use sol- vent. Further, never use drum cleaning powder. 4-29 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 210: Transfer Charging Roller

    When mounting it, be sure to fit the bottom of the spring of the pre-transfer arm into the seat (dent) in the feeder frame [4]. F04-903-02 4-30 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 211: Charging Roller Solenoid

    6) Remove the three screws [2], and shift the duct unit [3] to the side, and slide it out to the front. F04-904-02 4-31 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 212 [2]. F04-904-04 9) Remove the two screws [1], and discon- nect the connector [2]; then, detach the charging roller solenoid [3]. F04-904-05 4-32 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 213: Developing Assembly

    4) Holding the grip on the developing as- sembly, place your other hand on the bottom of the developing assembly; then, slide it out to the front. F04-905-01 4-33 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 214: Removing The Grip Assembly

    1) Remove the grip assembly. (item 9.5.2) 2) Remove the two screws [1], and free the three claws [2]. 3) Remove the developing assembly upper cover [3]. F04-905-04 4-34 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 215: Removing The Blade Base Unit

    9.5.6 Removing the Developing Cylinder 1) Remove the developing assembly upper cover. (p. 4-34P) 2) Remove the E-ring [1], bearing [2], and gear [3]. F04-905-07 4-35 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 216 [1] and the blade [2]. F04-905-09 6) Remove the screw [1], and remove the grounding plate [2]. 7) Remove the grip ring [3]. F04-905-10 4-36 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 217 [2] and the sleeve holder [3]. F04-905-12 10) Remove the developing cylinder [2] to- gether with the two bearings [1]. F04-905-13 4-37 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 218: Positioning The Developing Assembly Magnetic Seal

    The surface of the developing cylinder is highly susceptible to scratches. Be sure to fit the gap gauge on ends of the developing cylinder. 4-38 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 219: Removing The Paper Lint

    [1], and move it back and forth. F04-906-02 9.6.2 When Removing the Paper Lint Execute APVC correction in service mode. (p. 5-67T) APVC correction COPIER>FUNCTION>DPC> D-GAMMA 4-39 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 220 F04-907-02 4) Fit the new waste toner case [1], and mount the waste toner case cover [2] with a screw [3]. F04-907-03 4-40 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 221 5) Fit the waste toner case [1] back in the machine, and mount the waste toner case cover [2] with a screw [3]. F04-907-06 4-41 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 223 CHAPTER 5 PICK-UP/FEEDING SYSTEM COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 225: Chapter 5 Pickup/Feeding System

    Duplex copying Through path Related user mode Cassette auto selection (enabled/disabled) Paper icon Related mechanical adjustments Cassette horizontal registration adjustment Multifeeder horizontal adjustment T05-101-01 5-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 226: Arrangement Of Rollers

    Photosensitive drum Transfer charging roller [10] Fixing delivery roller [11] Delivery vertical path roller [12] Delivery roller [13] Duplex roller [14] Multifeeder pickup roller 5-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 227: Arrangement Of Motors, Clutches, And Solenoids

    Notation Name Main motor Pickup motor Delivery motor Duplex motor Registration motor Vertical path clutch Multifeeder clutch Pickup DOWN solenoid Multifeeder rely releasing solenoid 5-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 228: Arrangement Of Sensors

    No. 1 delivery paper sensor PS16 No. 1 delivery full sensor PS17 Duplex inlet paper sensor PS18 Duplex outlet paper sensor PS22 Multifeeder paper sensor T05-102-01 5-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 229: Detecting Jams

    Pickup assembly Motor Sensor Cassette 1 Pickup motor (M2) Cassette 1 retry sensor (PS7) Cassette 2 Pickup motor (M2) Cassette 2 retry sensor (PS8) T05-201-01 5-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 230 PS13 Fixing feeding sensor PS15 No. 1 delivery paper sensor PS17 Duplex inlet paper sensor PS18 Duplex outlet paper sensor PS22 Multifeeder paper T05-201-02 5-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 231: Stationary Jam

    The following are retained in response to a jam, and brought back to use after the jam has been removed. • Remaining number of copies to make • Selected copying mode 5-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 232: Pickup Assembly

    [11] Cassette pickup PCB Separation roller Main motor Lifter Pickup motor Vertical path roller Registration motor Vertical path clutch Registration roller Pickup DOWN solenoid 5-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 233: Outline

    The drive for the vertical path roller and the No. 2 registration roller is provided by the pickup motor (M2) through the vertical path clutch (CL1). The registration roller is driven by the registration motor (M9). 5-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 234: Sequence Of Operations (Pickup)

    Print start PRINT LSTR Pickup down solenoid(SL1) Pickup motor(M2) Retry sensor(PS7) Vertical path roller clutch(CL1) Pre-registration paper sensor(PS9) Registration paper sensor(PS10) Regist motor(M9) F05-303-01 5-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 235: Operation Of The Cassette Lifter

    The foregoing series of operation is repeated to maintain the height of the paper stack to a specific level. The cassette pickup operation ends when paper runs out and the cassette pa- per sensor detects the absence of paper. 5-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 236: Releasing The Lifter

    Be sure to turn off and then on the main power so that the machine will be in standby state whenever the cassette must be slid out. 5-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 237: Rotating The Pickup Roller

    The up and down movement of the pickup roller when the cassette is set in the machine is driven with reference to the position of the pickup roller shaft. [1] Pickup motor (M2) [2] Gear 1 F05-305-01 5-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 238: Pickup Roller

    Pickup Drive for the Lower Cassette Holder (pickup motor CCW rotation) Feeding roller Cassette pickup motor (M2) Pickup roller Separation roller Gear 1 F05-305-03 5-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 239 Feeding roller Feeding roller shaft Pickup roller Pickup roller shaft Roller holder Pickup lever Cam 1 (rotates when SL1 goes ON) Pickup solenoid (SL1) F05-306-02 5-15 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 240: Pickup Retry Operation

    *1:retry operation is executed if paper does not arrive after moving it over ‘distance to the retry sen- sor + 100 mm’. F05-307-01 Retry Operation 5-16 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 241 Pickup motor Retry sensor *1:paper moved by the retracting roller for a equivalent of a distance over which paper may be moved 10 cm. F05-307-02 5-17 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 242: Operation Other Than Cassette Pickup (Standby)

    (SL1) go ON to swing the pickup lever. [1] Cassette [2] Lever 1 [3] Pickup roller [4] Feeding roller [5] Pickup roller shaft F05-308-01 5-18 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 243: Moving Up The Lifter/Moving Down The Pickup Roller Shaft (Cassette Slid In)

    Pickup roller shaft Lifter trigger lever F05-308-02 5-19 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 244: Moving Up The Pickup Roller Shaft And Releasing The Separation Roller Pressure (Cassette Slid Out)

    [1] Cassette [2] Lever 1 [3] Pickup roller [4] Feeding roller [5] Pickup roller shaft F05-308-03 5-20 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 245 [3] Separation roller F05-308-04 b. Releasing the Lifter The lifter is released when the cassette is slid out while the machine is in standby state. 5-21 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 246: Detecting The Level Of Paper

    1 bar about 10% or less of capacity no bar No paper light-blocking plate over the sensor. light-blocking plate not over the sensor. T05-309-01 5-22 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 247: Detecting The Presence/Absence Of Paper Inside The Cassette

    (Q1604 for cassette 1; Q1605 for cassette 2). Q1604: cassette 1. Q1605: cassette 2. Paper detecting lever F05-310-01 5-23 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 248: Identifying The Size Of Paper

    When the cassette is slid into the machine, the cassette side detecting switch recognizes the paper configuration (AB or Inch) [1] Dial [2] AB-/Inch-setting switch [3] Size detecting cam F05-402-01 5-24 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 249: Paper Size

    Note 1:U Cassette The following are special types of paper: U1: FOOLSCAP/OFFICIO/A-OFFICIO/E-OFFICIO/B-OFFICIO/A-LGL U2: FOLIO U3: A-FLS U4: G-LTR U5: G-LTR(R) U6: G-LGL U7: X-LGL U8: K-LGL(R) 5-25 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 250: Paper Size List

    Combination of states of cassette size detection switches Main scanning Sub scanning Cassette name SW1 direction (mm) direction(mm) No cassette STMT STMTR (A-LTR) LTRR (A-LTRR) 11×17 T05-403-01 List of Paper Sizes 5-26 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 251: Multifeeder

    Registration roller Separation pad DC controller PCB Paper guide plate Main motor Multifeeder tray Multifeeder clutch Drive cam Multifeeder holding plate Spring cutch releasing solenoid 5-27 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 252: Identifying The Size Of Paper In The Multifeeder

    Use it to adjust the paper width basic value of A6R for the manual feed tray. COPIER>ADJUST>CST-ADJ>MF-A4 Use it to adjust the paper width basic value of A4 paper for the manual feed tray. 5-28 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 253: Controlling The Registration Roller

    6.2 Control System Registration rollers Registration drive signal DC controller J309 F05-602-01 COPIER>ADJUST>FEED-ADJ>REGIST Use it to adjust the timing at which the registration roller is started. 5-29 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 254: Double-Sided Printing

    As many as two sheets may exist at a time between the registration sensor and the duplex paper sensor. COPIER>ADJUST>FEED-ADJ>ADJ-REFE Use it to adjust the image write start position in main scanning direction for re-pickup. (-100 to 100 mm) 5-30 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 255: Outline Of Operations

    4) The 2nd sheet is picked up, and the 4th side ery assembly, and is then sent to the duplex is printed. feeding assembly. F05-703-01 5-31 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 256 8) The 3rd sheet is picked up, and the 6th side in the duplex feeding assembly. is printed. After this operation, a series of processes are repeated. F05-703-02 5-32 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 257: Detecting The Horizontal Registration Position

    Related service mode: COPIER>ADJUST>FEED-ADJ>ADJ-REFE Related error code: E051 (home position not detected within specific time) T05-703-01 PS11 Copy paper 10mm(approx.) Detecting start position Home position F05-703-01 5-33 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 258: Operation

    SP. start position of the duplex horizontal sensor. detection start position of the duplex horizontal registration sensor. F05-703-02 5-34 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 259: Controlling The Pickup Assembly Motor

    (M3) E051 Others Registration moter (M9) Jam occurred Delivery moter (M5) Jam occurred T05-801-01 DC controller Feeder driver J302 J1601 +24V J1602 (IC303) F05-801-01 5-35 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 260: Disassembly And Assembly

    The toner must not be disposed of into fire to avid explosion. 8. Do not operate the machine without locking the feeding assembly in place to avoid dam- age. 5-36 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 261: Pickup Assembly

    7) Disconnect the two connectors [1]. 8) Remove the seven screws [2], and re- move the screw [3] from the right rear; then, detach the pickup assembly [4]. F05-901-03 5-37 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 262: Removing The Pickup/Feeding/Separation Rollers

    9.1.3 Removing the Pickup Solenoid 1) Remove the pickup assembly. (p. 5-37P) 2) Disconnect the connector [1]. 3) Remove the screw [2], and detach pickup solenoid [3]. F05-901-05 5-38 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 263: Removing The Frame Lid

    [2]; mount back the bush- ings; then, check to see if the harness is routed correctly by looking through the opening in area A. F05-901-08 5-39 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 264: Removing The Pickup Motor

    9.1.6 Remove the Vertical Path Cultch 1) Remove the frame lid. (p. 5-39P) 2) Remove the flange [1], belt [2], and gear [3]. F05-901-11 5-40 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 265: Removing The Horizontal Registration Sensor Shift Motor

    3) Remove the two screws [2], and detach the horizontal registration unit. [3]. F05-901-13 4) Remove the two screws [1], and detach the horizontal registration sensor shift motor [2]. F05-901-14 5-41 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 266: Checking The Image Rear Front Position

    COPIER>FUNCTION>C1- ADJ-Y/C2-ADJ-Y/C3-ADJ-Y/ C4-ADJ-Y Use it to adjust the image read start position. If correction in service mode fails, make the following adjustments. 5-42 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 267 3) Loosen the screw [1], and adjust the horizontal registration plate [2]. When making adjustments, try to match the arrow [3] against the index (each graduation being about 1 mm). F05-901-17 5-43 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 268: Removing The Multifeeder

    F05-902-02 4) Open the multifeeder tray once again, and detach it to the right. 5-44 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 269: Tray Pickup Roller

    When mounting, be sure that the pin notch (cross-shaped) in the collar [6] of the multifeeder tray pickup roller [5] is toward the rear. F05-902-04 5-45 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 270 A, pull the multifeeder intermediate retaining plate [2] in the direction of B to detach. 7) Remove the separation pad [4]. F05-902-07 5-46 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 271: Attaching The Timing Belt Of The Multifeeder Tray

    COPIER>FUNCTION>MF- ADJ-Y Use it to adjust the image read start position. If correction in service mode fails, make the following adjustments. 5-47 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 272 1) Open the multifeeder tray. 2) Loosen the two screws [1], and move the side guide plate unit [2] back and forth to adjust. F05-902-10 5-48 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 273: Feeding Assembly

    12) While taking care not to trip them on the flapper [8] and the like, detach the feeding assembly [2] to the front. F05-903-03 5-49 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 274: Mounting The Feeding Assembly

    1) Fit the hinge [2] of the feeding assem- bly in the hinge hole [3] in the frame (rear) of the host machine. F05-903-04 5-50 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 275: Registration Roller Assembly . 5-51P

    F05-904-02 7) Remove the spring [1] from the front. 8) Remove the stepped screw [2], and de- tach the developing assembly base [3]. F05-904-03 5-51 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 276 [3]. 14) Remove the upper registration roller [4]. F05-904-05 15) Remove the E-ring [1] at the rear, and detach the busing [2]. F05-904-06 5-52 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 277 CHAPTER 5 PICK-UP/FEEDING SYSTEM 16) Remove the E-ring [1] at the front, and detach the bushing [2]. 17) Remove the lower registration roller [3]. F05-904-07 5-53 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 279 CHAPTER 6 FIXING SYSTEM COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 281 Cleaning roller Error detection [1] Temperature error detection by thermistor [2] Overheating detection by thermal switch Fixing film Equipped with rotation detection mechanism T06-101-01 6-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 282 Thermal switch (TP1) Fixing main heater (H1) Fixing sub heater (H2) Fixing motor Fixing delivery roller Fixing lower roller Cleaning roller Main power supply PCB F06-101-01 6-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 283 Temperature control, error detection Sub thermistor Error detection Thermal switch Operating temperature: 250 ± 7°C Fixing film sensor PS26 Rotation detection; reflection type sensor T06-101-02 6-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 284 E014 (fixing motor speed error) Indicates that the drive lock signal cannot be detected with 1.3 sec after the fixing motor drive signal (M4) is generated. 6-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 285: Controlling The Fixing Film Speed

    (Blurry images can occur 400-some millimeters of the trailing edge.) This mode may also be used to adjust the reproduction ratio in feed direction. 6-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 286 Main power supply PCB RelayRL1 Heater relay circuit High- temperature detection Thermal switch circuit (TP1) IC300 Fixing main A/D converter thermistor (200V) Fixing sub thermistor IC334 F06-301-01 6-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 287: Temperature Control

    [7] Fixing temperature switch-over The target temperature for fixing control is Upon selection COPIER>OPTION>BODY> switched. FIX-TEMP 1: -10°C 2: -6°C 3: -3°C 4: +3°C 5: +6°C 6: +10°C 7: +15°C T06-302-01 6-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 288: Fixing Temperature Control

    Bond paper 210˚C mode 205˚C 200˚C 195˚C Thick paper 190˚C mode 185˚C 180˚C 175˚C Plain paper mode 170˚C 165˚C Lower←Fixing lower temperature estimate→Higher F06-302-01 6-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 289: Detecting Errors

    PCB RelayRL1 Heater relay circuit High- temperature Thermal switch detection circuit (TP1) IC300 A/D converter Fixing main (200V) thermistor Fixing sub thermistor IC334 F06-303-01 6-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 290 (as occurring immediately after the switch is turned on/off). 6-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 291: Disassembly And Assembly

    The door switch or the main power switch must be turned off whenever the duplex unit or the fixing/feeding unit must be slid out. 6-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 292: Fixing Assembly

    2) Remove the screw [1], and detach the connector cover [2]. F06-401-02 3) Remove the screw [1], and detach the riser guide [2]. F06-401-03 6-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 293: Removing The Fixing Assembly

    [2] to the rear to re- move. 3) Remove the screw [3], and detach the sensor unit [4] and the sensor unit guide [5]. F06-401-06 6-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 294: Removing The Roller Bushing, Conducting Rubber, And Fixing Roller

    1) Remove the fixing assembly. (p. 6-13P) 2) Remove the E-ring [1], and detach the gear [2]. F06-401-09 3) Remove the fixing film unit. (p. 6-13P) 6-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 295 [1], and slide it to the rear to re- move. F06-401-11 6) Detach the two roller bushings [2] from the fixing roller [1]. 7) Remove the conducting rubber [3]. F06-401-12 6-15 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 296 [2] to free and detach. After mounting it, look from below to make sure that the claw [3] is positioned correctly. F06-401-14 6-16 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 297 [3] of the fixing drive unit (e.i., where the rear [4] of the gear of the locking cam unit is in contact with the cut-up [5] of the frame). F06-401-17 6-17 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 299: Chapter 7 Externals And Controls

    CHAPTER 7 EXTERNALS AND CONTROLS COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 301: Control Panel

    Use it to end a check on the activation of the LEDs in the control panel. COPIER>FUNCTION>PANEL>KEY-CHK Use it to start a check on key inputs. COPIER>FUNCTION>PANEL>TOUCHCHK Use it to check the coordinates on the touch panel. 7-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 302: Fans

    Prevents curling of paper No (24 V) E805-0005 The curl reducing fans 1 and 2 are enabled or disabled in service mode: COPIER>OPTION>BODY>DECRL-FN> T07-201-01 7-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 303 CHAPTER 7 EXTERNALS AND CONTROLS The arrangement of the fans and the directions of current are as follows: F07-201-01 7-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 304: Operation

    *1: Rotates for 30 sec after the leading edge sensor goes ON during printing; if the sensor goes ON for a second time during the 30-sec period, rotates for another 30 sec. F07-202-02 7-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 305: Power Supply

    PCB Thermistor power supply PCB (200 V) • Supplies power to thermsitor Leakage breaker • Cuts power in response to error T07-301-01 7-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 306: Power Supply

    Main heater Sub heater Triac Side paper deck Options 24VA1 power Finisher supply 24VA2 Side paper deck DC power supply AC power supply F07-301-01 7-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 307: Power Outputs

    Composite power supply PCB AC/DC converter Accessories Main power supply PCB power supply PCB Main power stitch AC/DC AC/DC converter converter Switch PCB F07-301-02 7-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 308: Rated Outputs Of The Main Power Supply Pcb

    Note: The above assumes that the AC input is between 85 and 135 V for the 100/120V model, and between 187 and 264 V for the 230V model. 7-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 309 Note: The above assumes that the AC input is between 85 and 135 V for the 100/120V model, and between 187 and 264 V for the 230V model. 7-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 310: Protective Functions

    PCB, if 3VB stops from the composite power supply PCB be- cause of a fault in the high-violate output or melting of the fuse, all outputs of power will be cut. 7-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 311: Others

    In silent mode, the drive of the laser scanner motor during standby is stopped for a spe- cific period of time* after the start of standby to reduce the machine’s operating noise. *The length may be changed in user mode. 7-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 312: Disassembly And Assembly

    6. The door switch or the main power switch must be turned off whenever the duplex unit or the fixing/feeding unit must be slid out. 7-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 313: External Covers

    [13]Left rear cover (1 screw) [14]Waste toner case cover (1 screw) [12] [15]Rear cover (7 screws) [16]Right inside cover (7 screws) [15] [10] F07-501-01 7-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 314: Removing The

    6) Remove the grip ring [2], and detach the feeding lever [3]. 7) Remove the six screws [4], and detach the inside cover [5]. F07-501-03 7-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 315: Removing The Support Cover

    4) Remove the screw [1], and detach the support cover [2]. Take care not to break the claw (circled) behind the support cover. F07-501-04 7-15 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 316: Control Panel

    3) Remove the two screws [1], and discon- nect the connector [2]. F07-502-01 4) Shift the control panel [1] to the left, and lift it to detach. F07-502-02 7-16 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 317: Pcbs

    1) Remove the rear cover. (7 screws) 2) Remove the 12 screws [1] (if the HDD unit [2] has been removed, 9 screws); then, detach the controller cover [3]. F07-503-02 7-17 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 318: Removing The Hdd

    3) Remove the four screws [2], and detach the HDD support base [3]. F07-503-03 4) Remove the four screws [1], and detach the HDD [2]. F07-503-04 7-18 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 319: Removing The Hdd Unit

    3) Remove the HDD unit. (See item 5.3.5) 4) Disconnect all the connectors of the harness. 5) Remove the eight screws [1], and detach the controller box unit [2]. F07-503-06 7-19 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 320: Removing The Reader Controller Pcb

    6) Remove the screw [1] (1 each), and de- tach the two PCB guides [2]. 7) Remove the eight screws [3], and detach the main controller PCB [4]. F07-503-08 7-20 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 321 3) Disconnect the connector [1] to the main power supply. 4) Remove the two screws [2], and detach the accessories power supply [3]. F07-503-10 7-21 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 322: Removing The Accessories Power Supply

    3) Disconnect the connector [1] to the composite power supply. 4) Remove the four screws [2], and detach the main power supply [3]. F07-503-11 7-22 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 323: Chapter 8 Paper Deck-L1

    CHAPTER 8 PAPER DECK-L1 COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 325: Pickup

    The registration roller is controlled so that the leading edge of paper will match the image on the photosensitive drum. 8-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 326 CHAPTER 8 PAPER DECK-L1 DC controller PCB (host machine) Deck driver PCB PS1D CL1D PS6D CL2D SL1D F08-101-01 8-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 327: Sequence Of Pickup Operations (Deck)

    (M1D) Deck pickup clutch (CL2D) Deck pickup roller releasing solenoid (SL1D) Deck pickup sensor (PS6D) Deck feed sensor (PS1D) Deck feeding clutch (CL1D) F08-101-02 8-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 328: Detecting Paper In The Deck

    (OPTION>ACC-DK-P). 8-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 329: Detecting The Level Of Paper In The Deck

    100% to about 50% about 50% to about 10% No paper 1: light-blocking plate over the sensor. 0: light-blocking plate not over the sensor. T08-102-01 8-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 330: Deck Lifter

    Each time paper is supplied, the lifter repeats its descent movement until the deck lifter lower limit detecting switch (SW2D) is pushed (point of maximum paper supply). 8-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 331 [5] Deck open detecting switch [13]Deck lifter cable [6] Deck lifter lower limit detecting switch [14]Lifter [7] Deck open switch [15]Copy paper [8] Deck main motor 8-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 332: Indicating The Level Of Paper (Deck Front Cover)

    (while the white area de- creases), indicating the increasing level of paper. F08-103-02 8-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 333: Opening/Closing Of The Compartment

    SW2D Deck lifter lower limit detection signal (DLLD) Open Deck lifter motor drive signal -9,10 (host machine) 9 : LIFT_M_UP 10 : LIFT_M_DOWN F08-104-01 8-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 334: Sequence Of Operations

    (SW1D) Deck open sensor (PS9D) Deck lifter position sensor (PS4D) Deck lifter DOWN Deck lifter UP varies depending on the amount of paper. F08-104-02 8-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 335: Controlling The Deck Motor

    Side deck driver PCB +24V +5V Motor drive current switch FEED_M_A * DC controller FEED_M_A Motor rotation control circuit FEED_M_B FEED_M_B * Deck main motor F08-105-01 8-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 336: Controlling The Deck Lifter Motor (M2D)

    The deck lifter motor DOWN signal (LIFT_M_DOWN) is ‘0’. • The deck lifter UP signal (LIFT_M_UP) is ‘1’. The above conditions move down the lifter. 8-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 337 Side deck driver PCB Note: The communication conversion IC (IC4) is used to convert between serial signals and parallel signals. F08-105-02 8-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 338: Detecting Jams

    PS1D PS6D F08-201-01 Notation Name Function PS1D Deck feed sensor Detection of delay jam PS6D Deck pickup sensor Detection of delay jam T08-201-01 8-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 339 PRINT INTR SCAN Deck pickup clutch (CL2D) Jam check Deck pickup sensor (PS6D) Deck feed sensor Normal Error (PS1D) Deck main motor (M1D) F08-201-02 8-15 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 340: Disassembly And Assembly

    5. As a rule, the machine must not be operated with any of its parts removed. 8-16 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 341: External Covers

    [2] at the left rear to open the compartment [3]. F08-301-02 8-17 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 342 [2] to detach it to the front. F08-301-03 When mounting the front cover, be sure to match it against the coupling [1] of the paper level indicator. F08-301-04 8-18 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 343 [1] by hand so that the white area inside the window [3] increases, i.e., in the di- rection for the arrow [4]; move it until a little resistance is felt. F08-301-06-A 8-19 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 344: Sliding Out The Compartment

    3.1.3 Removing the Rear Cover 1) Release the deck from its host machine; then, remove the six crews [1], and de- tach the rear cover [2]. F08-301-07 8-20 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 345: Removing The Right Cover

    When mounting the front upper cover, take care not to trap the harness on the open switch PCB or to forget connecting the con- nectors. F08-301-10 8-21 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 346: Removing The Upper Cover

    2) Sliding out the compartment. (p. 8-17P) 3) Remove the front upper cover. (p. 8-21P) 4) Remove the two screws [1], and detach the upper cover [2]. F08-301-11 8-22 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 347: Paper Deck Body

    [2]. F08-302-01 2) Remove the right cover. (p. 8-21P) 3) Remove the two screws [1] from the right side. F08-302-02-A 8-23 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 348 5) Holding the deck [1] by the areas indi- cated, move and place the deck on the block of paper prepared previously (p. 8-23P). F08-302-03 8-24 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 349: Removing The Compartment

    3) Remove the right cover. (p. 8-21P) 4) Disconnect the connector [1] at the rear of the compartment, and remove the screw [2]; then, detach the harness unit [3]. F08-302-05 8-25 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 350 [3] about 1 cm, and remove it to the front. 7) Place the compartment [3] on the block of copy paper prepared previously. (p. 8-25P) F08-302-07 8-26 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 351: Changing The Deck Paper Size

    3.2.4 After Changing the Deck Paper Size Execute 'machine settings selection' in service mode, and make settings to suit the selected paper size. COPIER>OPTION>ACC>DK- Machine Settings 8-27 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 352: Checking The Image Rear Front Position

    COPIER>FUNCTION>DK- ADJ-Y Use it to adjust the image read start position. If correction in service mode fails, make the following adjustments. 8-28 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 353: Adjusting The Registration For The Deck

    [2] is about 3 mm when the compart- ment is fully slid out. (At this time, use the scale [5] on the front side plate as a reference.) F08-302-11 8-29 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 354: Drive System

    E-ring [3]; then, detach the deck feed- ing clutch [4]. When mounting the deck feed- ing clutch, be sure to fit the clutch in the rotation stop [5]. F08-303-01-B 8-30 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 355: Removing The Deck Main Motor (M1D)

    3) Fit a hex wrench [2] into the opening in the lifter drive shaft [1] to fix the lifter drive shaft [3] in place (against rota- tion). F08-303-03 8-31 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 356: Removing The Lifter Cable (Deck Front)

    5) Fit two long screwdrivers [3] through to keep the lifter in position. F08-303-05b 8-32 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 357 [10] on the inside, remove the two [11] set screws [12] of the pulley [11] on the outside, and detach the pulley on the outside. F08-303-07 8-33 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 358 F08-303-08 7) Remove the screw [1], and detach the sensor plate [2]. 8) Remove the five screws [3], and detach the plate [4]. F08-303-09 8-34 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 359 F08-303-10 10) Remove the five screws [1], and detach the lifter motor unit [2]. F08-303-11 8-35 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 360: Routing The Lifter Cable

    6) Mount the pulleys [8] to the lifter drive shaft; then, measure the distance from the base plate of the compartment to the top face of the lifter, making sure that the lifter is level. F08-303-12 8-36 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 361: Feeding Mechanism

    [2]. The deck pickup roller has a specific orientation (direction of rotation). Pay attention to it when mounting it. F08-304-03 8-37 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 362: Mounting The Deck Pickup Roller

    2) Turn over the deck pickup unit. 3) Remove the resin ring [1], and detach the deck pickup/feeding roller [2] and the drive belt [3] to the front. F08-304-06 8-38 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 363: Orientation Of The Deck Pickup/Feeding Roller

    [1], and detach the separation roller support plate [2]. F08-304-08 2) Remove the joint [1], and detach the deck separation roller [2]. F08-304-09 8-39 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 364: Adjusting The Deck Separation Roller Pressure

    If pickup failure occurs, move the spring in the direction of arrow A. • If double feeding occurs, move the spring in the direction of arrow B. F08-304-10 8-40 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 365 The solenoid must always be positioned in its initial loca- tion. F08-304-11 8-41 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 366 1) Remove the front upper cover. (p. 8-21P) 2) Remove the two screws [2] from behind the front upper cover [1], and detach the open switch PCB [3]. F08-305-02 8-42 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 367: Chapter 9 Cassette Feeding Unit-W1

    CHAPTER 9 CASSETTE FEEDING UNIT-W1 COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 369: Outline

    22.2 (W) × 26.7 (D) × 9.76 (H) inches Weight 28 kg / 61.7 lb Operating noise 3 dB or less + that of host machine T09-101-01 9-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 370: Arrangement Of Rollers

    The following rollers are used to move paper inside the machine: Notation Name Pickup roller Feeding roller Separation roller Pull-off roller Vertical path roller 9-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 371: Arrangement Of Motors, Clutches, And Solenoids

    The following motors, clutch, and solenoid are used to move paper inside the machine: Notation Name Pedestal main motor Cassette pickup motor CL1C Vertical path roller clutch SL1C Pickup roller descent solenoid 9-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 372: Arrangement Of Sensors

    Cassette 3 paper sensor Q1605 Cassette 4 paper sensor PS2C Cassette 3 re-try paper sensor PS3C Cassette 4 re-try paper sensor Q1603 Vertical path paper sensor 9-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 373: Detecting Jams

    2.1.2 Stationary Jams See the descriptions under “Pickup/Feeding System” in Chapter 5. 2.1.3 Jam History See the descriptions under “Pickup/Feeding System” in Chapter 5. 9-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 374: Pickup Assembly

    Pickup roller Cassette pickup PCB Feeding roller Main motor Separation roller Pickup motor Lifter CL1C Vertical path clutch Vertical path roller SL1C Pickup descent solenoid 9-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 375: Outline

    See the descriptions under “Pickup/Feeding System” in Chapter 5. 3.10 Detecting the Level of Paper See the descriptions under “Pickup/Feeding System” in Chapter 5. 9-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 376: Identifying The Size Of Paper

    4.2 AB/Inch-Setting Switch See the descriptions under “Pickup/Feeding System” in Chapter 5. 4.3 Paper Size See the descriptions under “Pickup/Feeding System” in Chapter 5. 9-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 377: Disassembly And Assembly

    As a rule, the machine must not be operated with any of its parts removed. 9-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 378: External Covers

    5.1 External Covers F09-501-01 [1] Cassette 3 [4] Right cover (2 screws) [2] Cassette 3 [5] Rear cover (2 screws) [3] Pickup cover [6] Left cover 9-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 379 4) Remove the cable [2] from the front support shaft [1]. 5) Shift down the pickup cover [3], and detach it to the right. F09-501-04 9-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 380: Removing The Pickup Cover

    9) Remove the screw [4], and detach the grounding wire [5]. 10) Remove the four screws [6], and detach the pickup unit [7]. F09-502-02 9-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 381: Removing The Pickup/Feeding/Separation Roller

    5.2.6 Removing the Vertical Path Clutch See “Pickup/Feeding System” in Chapter 5-9.1.6. 5.2.7 Adjusting the Registration for the Cassette Rear Front See “Pickup/Feeding System” in Chapter 5-9.1.8. 9-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 382: Pcbs

    [2] to the front to detach. 4) Disconnect the two connectors [3]. 5) Remove the cassette size detection unit. F09-503-02 9-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 383: Removing The Pedestal Controller Pcb

    3) Disconnect all the connectors. 4) Release the locking support [1]. 5) Remove the five screws [2], and detach the pedestal controller PCB [3]. F09-503-03 9-15 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 384: Drive Mechanisms

    2) Remove the rear cover. (2 screws) 3) Disconnect the connector [1]. 4) Remove the four screws [2], and detach the pedestal main motor [3]. F09-504-02 9-16 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 385: Mounting The Pedestal Main Motor

    1) When mounting the pedestal main mo- tor, be sure to tighten the screws in the order indicated in the figure: (1) through (4). F09-504-03 9-17 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 387 CHAPTER 10 INNER 2 WAY TRAY-A1 COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 389: Chapter 10 Inner 2Way Tray-A1

    Without the Saddle Finisher-G1 A: No 1 delivery slot (host machine) B: No. 2 delivery slot C: No. 3 delivery slot (Copy Tray-F1/ Saddle Finisher-G1) F10-101-01 10-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 390: Cross Section

    [2] No. 3 delivery flapper [3] No. 2 delivery roller [4] Tray B [5] No. 2 delivery inlet roller [6] No. 2 deliver inlet flapper 10-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 391: Outline

    SL4: 2-way delivery solenoid PS19B: No. 2 delivery sensor PS20B: No. 2 delivery full sensor PS21B: No. 3 delivery sensor PS4B: 2-way delivery open/closed sensor F10-201-01 10-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 392 2-way delivery outlet motor stop to rotate. No. 2 delivery slot No. 3 PS20B delivery slot PS21B PS19B No. 1 delivery slot F10-202-02 10-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 393: Delivery To The No. 3 Delivery Slot

    2) The 2-way delivery solenoid goes on, and the feeding path switches to the No. 2 delivery lot. No. 2 delivery slot No. 3 PS20B delivery slot PS21B PS19B No. 1 delivery slot F10-203-02 10-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 394 No. 3 delivery slot. No. 2 delivery slot No. 3 PS20B delivery slot PS21B PS19B No. 1 delivery slot F10-203-04 10-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 395: Detecting Jams

    No. 1 delivery slot PS13 PS19B: No. 2 delivery sensor PS21B: No. 3 delivery sensor PS24B: 2-way delivery open/closed sensor PS13: fixing/feeding sensor (host machine) F10-204-01 10-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 396: Delay Jam

    [1]: specific feeding time F10-204-02 Notation Name Delay jam PS13 Fixing/feeding sensor (host machine) (yes) PS119B No. 2 delivery sensor PS20B No. 3 delivery sensor 10-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 397: Stationary Jam

    2.4.5 Door Open Jam A door open jam will be identified if the 2-way delivery open/closed sensor (PS24B) identifies the state of the door as being open. 10-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 398: Disassembly And Assembly

    5. As a rule, the machine must not be operated with any of its parts removed. 10-10 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 399 [3] Connector cover (1 screw) 3.1.1 Removing the Inner 2-Way Delivery Unit 1) Remove the inside delivery tray. 2) Open the inner 2-way delivery unit [1]. F10-301-02 10-11 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 400 3) Remove the screw [1], and detach the connector cover [2]. F10-201-03 4) Disconnect the two connectors [1]. F10-201-04 5) Close the inner 2-way delivery unit [1]. F10-201-05 10-12 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 401 6) Remove the screw [1] and the stepped screw [2] from inside. F10-201-06 7) Remove the screw [1] and the stepped screw [2] from outside. F10-201-07 10-13 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 402: 2-Way Delivery Unit

    CHAPTER 10 INNER 2 WAY TRAY-A1 8) Remove the rib [2] from the stay [1] of the host machine, and remove the inner 2-way delivery unit [3]. F10-201-08 10-14 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 403 CHAPTER 11 ENVELOPE FEEDER ATTACHMENT-B1 COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 405: Host Machine

    [1] Side guide plate (front) [2] Side guide plate (rear) [3] Lifter [4] Lifter stop [5] Mounting screw (4 pc.) [6] Spring (2 pc. including attachment) F11-101-03 11-1 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 406 Uses that of the host machine. Power supply Dimensions 565(W)×523(D)×95(H)mm / 22.2(W)×20.6(D)×3.74(W)inches Weight 3.4 kg / 7.5 lb Operating environment As determined by host machine T11-102-01 11-2 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 407 176 × 250 (mm) Schneidersohne Kuvert No.15269 YOUKEI 4 105 × 235 (mm) Y-401 T11-102-02 Configuration of Envelopes COM10, Monarch, DL C5, YOUKEI 4 F11-102-01 11-3 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 408 Face of the Envelope (common) 10mm F11-102-02 • Back of the Envelope (COM10, Monarch, D, C5, YOUKEI 4) 10mm F11-102-03 • Back of the Envelope (B5) 10mm F11-102-04 11-4 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 409 11-5 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 410: Error Codes

    4.1 Making Selections *5*OPTION ENV_SW 1: enable 2: disable (the key ‘select envelope cassette’ offered as part of common settings in user mode will be dimmed) 11-6 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 411: Making Adjustments

    (front, rear) and the lifter [3]. F11-502-01 2) Holding the bottom (1st, 2nd loops) of the spring [1], turn it clockwise to free it from the envelope feeder. F11-502-02 11-7 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 412: Changing The Size

    (as by choosing the wrong mounting hole). See the next page for the correct mounting hole. 11-8 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 413 2) Register the specifications of the enve- lope using ‘register envelope’ offered as part of common settings. 3) Check to make sure that envelopes are fed correctly. 11-9 P COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 415: Troubleshooting

    TROUBLESHOOTING COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 417 Duplex Feeding Unit ..3-5T 2.5 Mounting the Copyboard 1.4 Adjusting the Image Leading Glass ........3-11T Edge Margin ......3-5T 2.6 Mounting the Reader Upper Frame ........3-12T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 418 3.4 The copy has uneven density 1.7 Checking the Periodically (darker at front) ...... 4-12T Replaced Parts ......4-2T 3.5 The copy has uneven density (lighter at front) ...... 4-12T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 419 ....... 4-29T 5.1.2 Separation/Feeding 4.2 Printer Unit ......4-30T Assembly ......4-43T 4.2.1 Pickup fails ...... 4-30T 5.1.3 Fixing/Delivery Assembly, Duplex Reversing Assembly ......4-43T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 420 4.2 FEEDER ........ 5-58T 2.1 COPIER ........5-6T 4.3 SORTER ........ 5-59T 2.2 FEEDER ........ 5-19T FUNCTION Operation/ I/O, I/O Display mode ....5-20T Inspection Mode ......5-61T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 421 F. List of Special Tools ......A-8 Circuit Diagram ....... A-5 G. List of Solvents/Oils ...... A-10 D. 2-Cassette Feeding Unit-W1 General Circuit Diagram ....A-6 COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 423: Chapter 1 Maintenance And Inspection

    CHAPTER 1 MAINTENANCE AND INSPECTION COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 425: Periodically Replaced Parts

    The cassette feeding unit does not have parts that require periodical replacement. 1.5 Inner 2-Way Tray The inner 2-way tray does not have parts that require periodical replacement. 1-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 426: Checking The Time Of Replacement

    240,000 Actual prints made (multifeeder) Fixing film unit (100V) FG6-5712 150,000 Fixing film unit (115V) FG6-6039 150,000 Fixing film unit (230V) FG6-6041 150,000 T01-203-01 1-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 427: Side Paper Deck

    Separation roller FF5-4634-020 120,000 Actual prints 2.6 Inner 2-Way Tray-A1 The inner 2-way tray-A1 does not have parts that are designated as a durable. 1-3 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 428 250,000 prints. (2) Scanner rail; clean the slide area, and apply silicone oil (FY9-6011). 1-4 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 429 14. Fill out the Service Book, and report to the person in charge; put a description of the check made on the operation of the leakage breaker in the Service Book. 1-5 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 430 Scanner rail × Silicone oil (S20; FY9-6011) Copyboard glass No. 1 through No. 3 mirror Original illumination reflecting plate Original size sensor Lens T01-401-01 1-6 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 431 Waste toner Waste toner case Inspect/remove. collection (Remove waste toner, assembly and then clean the toner case. Replase the toner case, if any.) 1-7 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 432 Transfer guide Cleaning Waste toner case Checking, disposing (Remove waste toner, and then clean the toner case, Replace the toner case, if any.) F01-500-01 1-8 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 433 2) Slide out the developing assembly [1]. 3) Dry wipe the bottom of the developing assembly. 4) Slide in the developing assembly. 5) Close the front door. F01-601-01 1-9 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 435: Chapter 2 Image Adjustment Basic Procedure

    CHAPTER 2 IMAGE ADJUSTMENT BASIC PROCEDURE COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 437: Checking The Scanner Side

    'OK!' is indicated. Is the copy image density End. Replace the composite normal? power supply PCB. Go to Checking the Printer Side (1/3). 2-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 438: Checking The Printer Side (1/3)

    (transfer charging roller) locked mechanism is faulty, replace the securely in place? transfer charging roller unit. Replace the laser scanner unit. 2-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 439: Chapter 3 Standards And Adjustments

    CHAPTER 3 STANDARDS AND ADJUSTMENTS COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 441: Image Adjustments

    F03-101-01 Image Leading Edge Margin F03-101-02 Left/Right Image Margin 2.5±1.5mm<2.5±2.0mm> 2.5±1.5mm F03-101-04 Left Non-Image Width F03-101-03 Leading Edge Non-Image < >: with DADF-H1 Width 3-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 442: Checking The Image Position

    2. Adjusting the image leading edge margin (registration) 3. Adjusting the left/right non-image width (CCD read start position) 4. Leading edge non-image width (scanner image leading edge position) 3-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 443: Adjusting Left/Right Lamge Margin

    3) Loosen the screw [1], and adjust the horizontal registration plate [2]. When making adjustments, try to match the arrow [3] against the index (each graduation being about 1 mm). F03-103-02 3-3 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 444 3 ±1 mm. 4) If the gap is not 3 ±1 mm, adjust the front cover. 3-4 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 445: Duplex Feeding Unit

    (A decrease by ‘12’ will (An increase by ‘12’ will increase decrease the margin by 1 mm.) the non-image width by 1 mm.) 2.5mm±2.0 F03-105-01 3-5 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 446: Adjusting The Leading Edge Non-Image Width

    CCD adjust- ment data on the service label. 1. CCD Auto Adjust COPIER>FUNCTION>CCD> CCD-ADJ 2. CCD Adjustment Data All items under COPIER>ADJUST>CCD. 3-6 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 447: Mounting The Motor Unit

    F03-202-02 6) Tighten the two screws to secure the motor unit in place. 3-7 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 448: Routing The Scanner Drive Cable

    4) Temporarily secure the cable fixing in place to the No. 1 mirror base. (Do not tighten the screw fully.) 5) Fit the reader upper frame. 6) Adjust the position of the No. 1 and No. 2 mirror bases. F02-203-01 3-8 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 449: Adjusting The Position Of The No. 1/No. 2 Mirror Base

    • For the Front (F marking) (initial; FY9-3009) (set for the machine) F03-204-01 • For the Rear (R marking) (initial; FY9-3009) (set for the machine) F03-204-02 3-9 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 450 5) Fully tighten the screw on the cable fix- ing so that it is secured on the No. 1 mirror base. 6) Detach the mirror positioning tool (2 pc.). 3-10 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 451: Mounting The Copyboard Glass

    800% enlargement copy to check.) • Thereafter, execute optimum position auto adjustment for the standard white plate to ensure correct shading correc- tion: COPIER>FUNCTION>CCD>SH- PS-ST. 3-11 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 452: Mounting The Reader Upper Frame

    COPIER>ADJUST>CCD 2.8 When Replacing the Reader Controller PCB See “Troubleshooting” > Chapter 3 “Standards and Adjustment” > 7. “Electrical Compo- nents” 3-12 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 453: Image Formation System

    The surface of the developing cylinder is highly susceptible to scratches. Be sure to fit the gap gauge on ends of the developing cylinder. 3-13 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 454: Removing The Paper Lint

    2) Remove the paper lint cleaning cover [1] by inserting a flat-blade screwdriver. F03-303-01 3) Slide out the paper lint cleaning lever [1], and move it back and forth. F03-303-02 3-14 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 455: Cleaning The Waste Toner Case

    5) Fit the waste toner case [1] back in the machine, and mount the waste toner case cover [2] with a screw [3]. F03-304-03 3-15 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 456: Fixing System

    [3] of the fixing drive unit (e.i., where the rear [4] of the gear of the locking cam unit is in contact with the cut-up [5] of the frame). F03-401-01 3-16 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 457: Paper Deck

    3-17 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 458: Adjusting The Paper Level Indicator

    [2] is about 3 mm when the compart- ment is fully slid out. (At this time, use the scale [5] on the front side plate as a reference.) F03-503-01 3-18 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 459: Mounting The Deck Pickup Roller

    2) Turn over the deck pickup unit. 3) Remove the resin ring [1], and detach the deck pickup/feeding roller [2] and the drive belt [3] to the front. F03-505-01 3-19 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 460 If pickup failure occurs, move the spring in the direction of arrow A. • If double feeding occurs, move the spring in the direction of arrow B. F03-507-01 3-20 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 461 The solenoid must always be positioned in its initial loca- tion. F03-508-01 3-21 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 462 1 mm, and then tighten the fixing screws. 10) Mount the right cover, and then put the paper back into the deck. 3-22 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 463 1) When mounting the pedestal main mo- tor, be sure to tighten the screws in the order indicated in the figure: (1) through (4). F03-601-01 3-23 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 464 (front, rear) and the lifter [3]. F03-702-01 2) Holding the bottom (1st, 2nd loops) of the spring [1], turn it clockwise to free it from the envelope feeder. F03-702-02 3-24 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 465 (as by choosing the wrong mounting hole). See the next page for the correct mounting hole. 3-25 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 466 2) Register the specifications of the enve- lope using ‘register envelope’ offered as part of common settings. 3) Check to make sure that envelopes are fed correctly. 3-26 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 467: Chapter 4 Troubleshooting Image Faults

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/ MALFUNCTIONS COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 469: Checking The Site Of Installation

    Copyboard glass (standard white plate) If the ADF platen, copyboard cover, or copyboard glass is soiled, clean it with a solution of mild detergent; if scratched, replace it. 4-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 470: Charging Roller And Static

    If the copies have uneven density (difference between front and rear), light images, or foggy background, try the Image Adjustment Basic Procedure first to see if the problem is corrected. 4-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 471: Others

    3. Condensation on the pickup/feeding guide can cause feeding faults. If condensation is noted, dry wipe the part, or leave the machine pow- ered and alone for 60 min. 4-3 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 472 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS Blank Page 4-4 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 474: Samples Of Image Faults

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 2 Samples of Image Faults 4-6 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 475: Troubleshooting Image Faults

    4) Is the coating on the developing cylinder even? Check the developing assembly. Scanner, Photosensitive drum 5) Clean the mirrors and lenses. Is the problem corrected? YES: End. Replace the drum unit. 4-7 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 476: The Copy Is Too Light (Including Solid Black)

    The paper may be moist. Advise the user on the correct method of storing paper. • Advise the user that the use of paper not of a recommended type may fail to produce poor images. 4-8 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 477 The resistance of the high-voltage cord (white) is about 10 kΩ • The resistance of the cord for the transfer guide is about 10 kΩ 4-9 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 478: The Copy Is Too Light (Entire Face, Considerable)

    (The resistance of the high-voltage cord of the transfer charging roller is about 10 kΩ.) YES: Check the composite power supply PCB and the DC controller PCB. 4-10 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 479 (Check to see that the developing block members are in firm contact with the photosensitive drum.) Fit the developing assembly once again. YES: • Check the developing assembly. • Check the developing bias. 4-11 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 480: The Copy Has Uneven Density (Darker At Front)

    Drum cartridge, Shading 6) Is there an uneven image in the halftone area of PG? YES: Replace the drum unit. Execute shading adjustment (i.e., FUNCTION>CCD>CCD-ADJ). 4-12 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 481: The Copy Is Foggy (Entire Face)

    YES: End. Developing bias, DC controller PCB 7) Try replacing the composite power supply. Is the problem corrected? YES: End. Replace the DC controller PCB. 4-13 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 482: The Copy Is Foggy (Vertical)

    4) Is there a scratch in the peripheral direction on the surface of the photo- sensitive drum? YES: Replace the drum unit. Check to see if the photosensitive drum is subjected to light from outside. 4-14 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 483: The Copy Has A Black Line (Vertical, Fine)

    4) Is there a scratch it the peripheral direction of the fixing roller? YES: Replace the fixing roller. Check the fixing inlet assembly for dirt. 4-15 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 484: The Copy Has A White Spot (Vertical)

    Change the setting in the following service mode to change the point of shading measurement: FUNCTION>SHDG-POS. If the problem is not corrected after several attempts, replace the copyboard glass. 4-16 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 485: The Copy Has A White Spot (Horizontal)

    5) Is there a white spot on the photosensitive drum during copying opera- tion? Check the transfer charging roller for leakage. YES: Check the developing bias. 4-17 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 486: The Back Of The Copy Is Soiled/Soiled Edge

    Fixing assembly 6) Execute fixing cleaning mode in the following service mode: COPIER>OPTION>BODY>FIX-CLN. Is the problem corrected? Replace the fixing cleaning roller. YES: End. 4-18 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 487: The Copy Has A Fixing Fault

    Service mode 8) Set priority on fixing in the following service mode: COPIER>OPTION>BODY>FIX-TEMP. Is the problem corrected? YES: End. 4-19 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 488: The Copy Has A Displaced Leading Edge

    Generate a PG test pattern ( [6] ; solid bal). • Make adjustments so that the leading edge margin is 2.5 ± 1.5 mm. A higher setting will decrease the margin. 4-20 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 489: The Copy Is Blurred

    4) Does the problem occur at intervals of about 35 mm? YES: Check the developing assembly. • Check the drum drive assembly. • Replace the drum unit. 4-21 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 490: The Copy Is Foggy (Horizontal)

    6) Make reduced copies (about 50% to 60%), and compare them against copies made in Direct. Is the position of the problem different? YES: Check the scanner. Check the feeding assembly. 4-22 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 491: The Copy Has Inadequate Sharpness

    Replace the DC controller PCB. Drum unit, Transfer charging system 5) Try replacing the drum unit. Is the problem corrected? YES: End. Check the transfer charging system. 4-23 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 492: The Copy Is Completely Blank

    9) Is about 12 VDC present on J602-1 of the CCD PCB? Is about 5 VDC present on J602-4? Check the wiring; if normal, replace the reader controller PCB. 4-24 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 493 Laser scanner unit, Drum unit 11)Try replacing the drum unit. Is the problem corrected? Check the laser shutter mechanism; if normal, replace the laser scanner unit. YES: End. 4-25 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 494: The Copy Is Completely Black

    YES: Replace the composite power supply PCB. Reader controller PCB, CCD unit 7) Try replacing the CCD unit. Is the problem corrected? Replace the reader controller PCB. YES: End. 4-26 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 495: The Copy Has A Block/White Dot After Replacement Of The Drum Unit

    YES: Check the reading glass for dirt and a scratch. Paper lint (droppings) can be suspected. Clean the ADF roller, original path, and reading glass. 4-27 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 496: Troubleshooting Malfunctions

    YES: Check the AC power line (power cord, leakage breaker, switch PCB, main power supply PCB (J6)) for poor wiring (i.e., electrical continuity); check the connectors for poor contact. 4-28 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 497: The Dc Power Is Absent

    J124-9, 10 J126-2, 3, 5, 7 YES: Check the wiring from each power supply PCB to each load. Replace the faulty power supply PCB. 4-29 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 498: Printer Unit

    J302A of the DC controller PCB? (J302A-1: 24 V, J302A-3: GND, J302A-6: IN1, J302A-7: IN2, J302A-8: IN3, J302A-8: IN4) YES: Replace the pickup PCB. Replace the DC controller PCB. 4-30 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 499: The Lifter Fails To Move Up (Pickup From The Cassette)

    COPIER>FUNCTION>PART>CHK>SL; i.e., SL-ON. Is the solenoid con- trol signal present at J302A-5 of the DC controller PCB? (J302A-5: FDOWN_SL*) YES: Replace the pickup PCB. Replace the DC controller PCB. 4-31 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 500: The Vertical Path Roller Fails To Rotate

    REG_A*, J309-3: 24 VU, J309-4: 24 VU, J309-5: REG_B, J309-6: REG_B*) YES: The registration motor is faulty. Replace the motor. The DC controller PCB is faulty. Replace the PCB. 4-32 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 501: Pickup From The Multifeeder Tray Fails (I.e., The Pickup Roller Fails To Rotate)

    J308A-1 and -2 on the DC controller PCB? (J308A- 2: 24 V, J308A-1: MLT_SL) YES: Check the wiring and the link; if normal, replace the solenoid. Replace the DC controller PCB. 4-33 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 502: The Photosensitive Drum Fails To Rotate

    YES: Check the wiring from the DC controller PCB to the pre-exposure lamp; if normal, replace the pre-exposure lamp. Replace the DC controller PCB. 4-34 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 503: Reader Unit

    Is the drive signal present at J401 of the reader controller PCB? (J401-5/6: +24 V, J401-1/2/3/4: drive pulse) YES: Replace the scanner motor. Replace the reader controller PCB. 4-35 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 504: The Scanning Lamp Fails To Go On

    PCB? (J402-2: LMP_ON, J402-3: GND, J402-4: +24 VU) YES: The scanning lamp is faulty. Replace the lamp. The reader controller PCB is faulty. Replace the PCB. 4-36 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 505: Message Indication

    2: J302-A11 (from 0 to 5 V)) The paper sensor or the pickup PCB is faulty. Replace the PCB. YES: The DC controller PCB is faulty. Replace the PCB. 4-37 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 506 PCB to the DC controller PCB? • Composite power supply PCB (J136A-3) • DC controller PCB (J301A-10) YES: Replace the DC controller PCB. Replace the composite power supply PCB. 4-38 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 507: Paper Deck

    Start key is pressed, is the clutch drive signal generated? (J5-B3: FEED_CL_ON*, J5-B4: 24 V) YES: Check the wiring; if normal, replace the clutch. Replace the deck driver PCB. 4-39 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 508: The Deck Lifter Fails To Move Up

    PCB change from about 0 to 5 V? YES: Check the lever and the wiring; if normal, replaced the switch. Replace the deck driver PCB. 4-40 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 509: Troubleshooting Feeding Faults

    The descriptions that follow are also grouped according to the locations of jams; the loca- tion and the nature of a specific jam may be checked in the machine’s service mode (COPIER>DISPLAY>JAM). F04-501-01 4-41 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 510: Pickup Assembly

    Does the main motor rotate? YES: Check the roller and the vertical path clutch of the vertical path as- sembly. Replace the main motor. 4-42 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 511: Separation/Feeding Assembly

    3. Fixing/ feed sensor lever, No. 1 delivery paper sensor lever Does the lever of the sensor in question move smoothly? Correct the lever so that it moves smoothly. 4-43 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 512: Duplex Feeding Assembly

    CHK. When the OK key is pressed, does the duplex motor rotate? YES: Check the roller of the duplex assembly. Check the wiring; if normal, replace the motor. 4-44 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 513: Faulty Feeding

    Is the fixing film, fixing lower roller, or cleaning roller faulty? YES: Clean or replace it. Check the delivery feeding assembly for a fault. 4-45 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 514: Outline Of Electrical Components

    FEED: pickup circuit PCB MPWS: main power supply PCB DECK-CON: side deck driver PCB DECK-FEED: 2-Cassette Pedestal Pickup PCB FAX-CON: G3 FAX control PCB 4-46 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 515: Checking The Photointerrupters

    For an open/closed sensor, the state in which the cover/unit is closed. • For a home position sensor or a set sensor, the item in question is in home position or set in place. 4-47 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 516 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2 E201 (reader unit/printer unit) 6.2.1 Clutches 6.2.2 Solenoids, Switches F04-602-01 4-48 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 517: Clutches

    1: ON, 0: OFF SW1 (MPWS) A3-12-B Main power switch SW2 (MPWS) A3-12-B Environment heater switch SW3 (MPWS) A3-14-B P008-7 Front cover switch 0: open, 1: closed 4-49 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 518: Motors (1/2)

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.3 Motors (1/2) M400 F04-602-02 4-50 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 519 A3-15-J P001-3 Fixing motor 0: ON, 1: OFF P001-4 1: ON, 0: OFF P008-5 0: lock M5 (DC-CON) A3-9-N P010-0 to 8 Delivery motor 4-51 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 520 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.3 Motors (2/2) M400 F04-602-02 4-52 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 521 M9 (DC-CON) A3-14-M P002-5 Registration motor 1: OFF, 0: ON P020-6, 7 M10 (DC-CON) A3-14-J P001-2 Laser scanner motor 0: lock P008-3 0: lock 4-53 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 522: Fans

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.4 Fans F04-602-03 4-54 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 523 Curl reducing fan 1 1: ON, 0: OFF P009-6 0: ON FM5 (DC-CON) A3-7-I P005-7 Curl reducing fan 2 1: ON, 0: OFF P009-7 0: ON 4-55 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 524: Sensors (1/3)

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.5 Sensors (1/3) PS400 PS401 PS10 PS23 PS22 PS1-6 PS11 PS12 F04-602-04 4-56 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 525 50% (bit6=1; bit7=1) Cassette 2 paper 100% (bit6=0; bit7=0) level sensor 2 PS7 (DC-CON) A3-20-M P015-0 Cassette 1 re-try 1: present, 0: absent (paper) paper sensor 4-57 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 526 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.5 Sensors (2/3) PS400 PS401 PS10 PS23 PS22 PS1-6 PS11 PS12 F04-602-04 4-58 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 527 S2 (DC-CON) A3-6-I P008-2 Waste toner case full sensor 1: full (waste toner) S3 (DC-CON) A3-17-N P023-4, P33 (humidity) Environment sensor P023-5, P34 (room temperature) 4-59 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 528 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.5 Sensors (3/3) PS400 PS401 PS10 PS23 PS22 PS1-6 PS11 PS12 F04-602-04 4-60 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 529 P013-0 to 4 Cassette 1 size sensor S5 (DC-CON) A3-16-J P014-0 to 4 Cassette 2 size sensor VR1 (DC-CON) A3-18-M P023-2, P31 Multifeeder paper width sensor 4-61 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 530: Lamps, Heaters, And Others

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.6 Lamps, Heaters, and Others LAMP1 PLG1 LAMP2 H1,H2, TP1, TH1,TH2 F04-602-05 4-62 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 531 PLG1 (DC-CON) A3-14-A Power supply cord TH1 (MPWS) A3-12-J P023-0, P29 Main thermistor TH2 (DC-CON) A3-12-J P023-1, P30 Sub thermistor TP1 (DC-CON) A3-9-B Thermal switch 4-63 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 532 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.2.7 PCBs [14] [13] [10] [12] [10] [11] [10] F04-602-06 4-64 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 533: Pcbs

    Includes counter PCB, Main controller PCB processing/system. soft IDPCB, Centronics PCB. [11] Controls the DC-DC converter. 200V model only. Thermistor separation power supply PCB 4-65 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 534: Side Paper Deck-L1

    CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.3 Side Paper Deck-L1 6.3.1 Clutches 6.3.2 Solenoids, and Switches 6.3.3 Motors SW100D SW1D SW2D SL1D CL2D CL1D LED100D SL2D F04-603-01 4-66 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 535 Electrical signal (target) Reference to general I/O address Remarks Name circuit diagram I/O indication M1D (DECK-CON) A5-5-H Deck main motor M2D (DECK-CON) A5-5-B Deck lifter motor 4-67 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 536 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.3.4 Sensors 6.3.5 PCBs PS4D PS2D PS8D PS9D PS1D PS3D PS6D PS7D PS5D F04-603-02 4-68 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 537 PS8D (DECK-CON) A5-7-C Deck paper supply position sensor PS9D (DECK-CON) A5-3-C Deck open sensor 6.3.5 PCBs Ref. Description Remarks Name Side deck driver PCB 4-69 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 538 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.4 2-Cassette Feeding Unit-W1 6.4.1 Clutches 6.4.2 Solenoids and Switches 6.4.3 Motors SL1C CL1C F04-604-01 4-70 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 539 Electrical signal (target) Reference to general I/O address Remarks Name circuit diagram I/O indication M1C (PEDE-CON) A6-2-E Pedestal main motor M2C (PEDE-FEED) A6-11-G Cassette pickup motor 4-71 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 540 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.4.4 Sensors 6.4.5 PCBs PS1C PS2C Q1603~1609 PS3C F04-604-02 4-72 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 541 Cassette 4 paper level sensor 1 6.4.5 PCBs Ref. Description Remarks Name Controls the pickup assembly. 2-cassette pedestal pickup PCB Controls the paper deck. Pedestal controller PCB 4-73 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 542 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.5 Inner 2-Way Tray-A1 6.5.1 Solenoids 6.5.2 Motors 6.5.3 Sensor PS20B PS24B PS19B PS21B SL3B F04-605-01 4-74 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 543 PS21B (DC-CON) A7-8-G P016-4 No. 3 delivery sensor 1: present, 0: absent (paper) PS24B (DC-CON) A7-4-G P016-7 2-way delivery open/closed 1: open, 0: closed sensor 4-75 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 544 CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS 6.6 Super G3 FAX Board-J1 6.6.1 Others 6.6.2 PCBs [3] [4] F04-606-01 4-76 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 545 Stores firmware for the fax 16M bit DIMM system. Generates a pseudo CI signal. 100V Pseudo CI PCB Detects off-hook state of the 120V Off-hook detection PCB telephone 4-77 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 546 Do not touch those VRs and check pins not discussed herein; they are for exclusive use in the factory, and require high accuracy and special instru- ments. 4-78 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 547 Box text file data and control data on the hard disk will be ini- tialized. 4) Download all data using the Service Support Tool. 4-79 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 548 J312 J314 J311 J320 J332 F04-607-02 6.7.3 Reader Controller PCB J406 J405 J404 J403 J402 J401 J407 J400 J408 J413 J410 J409 J412 F04-607-03 4-80 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 549 When replacing the PCB, be sure to enter the settings indicated on the service label [1] in service mode. F04-607-04 6.7.5 Fixing Film Sensor PCB J3146 F04-607-05 4-81 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 551: Chapter 5 Survice Mode

    CHAPTER 5 SERVICE MODE COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 553: Outline Of Service Mode

    Select a Level 2 item from the list. Level 3 Item Level 3 Item Level 3 Item Level 3 Item screen screen screen screen Previous/Next page Previous/Next page Previous/Next screen F05-101-01 5-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 554: Starting Service Mode And Making Selections

    ADF service mode FEEDER if installed. SORTER Finisher service mode if installed. Fax board service mode if installed. BOARD Accessories board service mode if installed. F05-102-01 5-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 555: Ending Service Mode

    You can print out the settings stored in the machine in service mode: COPIER>FUNCTION>MISC-P>P-PRINT. In addition, you can obtain a new service label using service mode: COPIER>FUNCTION>MISC-P>LBL-PRINT. F05-104-01 5-3 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 556: Using Service Mode

    Level 1 items Touch an item to VERSION select. USER ACC-STS ANALOG CST-STS SENSOR MISC Level 2 items Touch an item to select. HV-STS ALARM-2 F05-105-02 5-4 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 557: Level 3 Item Screen

    Clear Start key: use to make a copy with ending service mode. F05-105-04 5-5 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 558: Display Control Display Mode

    The following screen will appear in response to COPIER>DISPLAY; the respective item follows: Function Adjust Counter Display Option Test VERSION USER ACC-STS ANALOG CST-STS SENSOR HV-STS ALARM-2 F05-201-01 5-6 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 559 Indication: for copier model, xx.yyC; for PSPCL model; xx.yyP; for PCL model, xx.yyL DIAG-DVC Indicates the version for the remote diagnostic device. Indicates the version of the RUI. 5-7 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 560 LANG-HU Indicates the version of the Hungarian file. LANG-KO Indicates the version of the Koran file. LANG-NL Indicates the version of the Dutch file. 5-8 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 561 Indicates the version of the Swedish file. LANG-TW Indicates the version of the Chinese file (traditional). LANG-ZH Indicates the version of the Chinese file (simplified). 5-9 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 562 (00: Canon, 01: OEM, 02: common (all)) paper size configuration code (00: AB, 01: Inch, 02: A, 03: all sizes) MODEL Indicates the model (0: iR2200, 1: iR2800, 2: iR3300). COPIER>DISPLAY>ACC-STS <ACC-STS> Indicates the connection of accessories. FEEDER Indicates the connection of an ADF.
  • Page 563 Indicates the temperature of the fixing heater. (main thermistor; in °C) FIX-E Indicates the temperature of the edge of the fixing heater. (sub thermistor; in °C) 5-11 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 564 Indicates the size of paper in the cassettes and the manual feeder. WIDTH-MF Indicates the width of paper in terms of paper size (manual feed). 5-12 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 565 T05-201- 05, -06. Indicates the source of paper. See T05-201-03. HHHHHH Indicates the soft counter of the source of paper. IIIII Indicates paper size. 5-13 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 566 2-way delivery open/closed sensor (PS24B)/ relay delivery open/closed sensor (PS24Z) xx36 right cover open/closed sensor (PS1C) xx37 deck set sensor (PS5D) xx39 finisher front cover sensor (S1) T05-201-02 5-14 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 567 PS19Z delay 0214 relay delivery sensor PS19Z stationary 0B35 relay delivery cover PS24Z open jam 0B39 front cover open jam T05-201-06 5-15 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 568 Indicates the location of occurrence. 0: copier/main controller 1: feeder 2: finisher 3: CFF 4: reader 5: printer 6: PDL 7: fax not used 5-16 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 569 COPIER>DISPLAY>SENSOR <SENSOR> Indicates the condition of sensors. DOC-SZ Indicates the size of the original detected by the original size sensor. 5-17 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 570 Indicates the total counter reading at time of See the table below. occurrence. GGGG Indicates the detail code. R&D control code. HHHHHHHH Indicates the total counter of occurrence. 5-18 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 571 0001: stitch staple absent puncher system of 0001: punch waste case full sorter/finisher FEEDER>DISPLAY 2.2 FEEDER FEEDSIZE Indicates the size of the original detected by the ADF. 5-19 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 572 Input/output port of finisher controller PCB MN-CON Input/output port of main controller PCB F05-301-01 <Guide to the screen> P001 xxxxxxxxxxxxxxxx bit 0 bit 15 address 5-20 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 573: Inner 2-Way Tray-A1

    IN3 relay delivery assembly 2-way delivery outlet motor pulse signal IN4 Inner 2-way tray-A1 relay delivery outlet motor pulse signal IN4 relay delivery assembly 5-21 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 574 0: in rotation curl reducing fan 1 rotation detection signal 0: in rotation curl reducing fan 2 rotation detection signal 0: in rotation 5-22 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 575 0 optional output signal 1 optional output signal 2 optional output signal 3 5-23 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 576 0 optional input signal 1 optional input signal 2 optional input signal 3 optional input signal 4 not used not used not used 5-24 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 577 2-way tray absent: bit 6=1 saddle finisher detection signal finisher: bit6=0, bit 7=1 saddle finisher: bit 6=0, bit 7=0 5-25 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 578 1: paper present P026 not used not used not used not used not used not used not used not used 5-26 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 579 ON signal A/D hexadecimal notation humidity detention signal A/D hexadecimal notation room temperature detection signal A/D hexadecimal notation AC monitor signal A/D hexadecimal notation 5-27 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 580 0: ON not used M400 scanner drive current set signal analog signal not used 5-28 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 581 IO-P09 0 ON LED (not used) not used not used not used not used not used not used not used 5-29 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 582 If the port is ‘0’ when 24V is supplied, the initial rotation is omitted (to prevent turning on the reader in response to a PING command while the machine is in sleep mode); if ‘1’, the initial operation is executed. 5-30 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 583 ROM connection detection 1: connected flash RPOM R/B# 0: Busy, 1: Ready parallel EEPROM R/B# for factory battery alarm 0: Normal, 1: Error 5-31 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 584 SSB ID FOPTI0N1 for fax SSB ID FOPTI0N0 for fax SSB ID P009 IPC-PB not used 0: fixed P010 IPC-PO not used 0: fixed 5-32 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 585: Feeder

    EEPROM chip select PI10 original set sensor signal 1: paper present cover open/close sensor signal 0: open feed motor clock signal pickup motor clock signal 5-33 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 586 IO-P11 0-7 not used AD-P01 original width volume (analog port) AD-P02 feed motor current level (analog port) AD-P03 pickup motor current level (analog port) 5-34 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 587: Finisher-J1

    1: up ON (output) 1 not used stack try ascent/descent motor CCW signal 1: down ON not used delivery motor current switch 2 (T05-301-01) not used 5-35 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 588 2 signal 0: current medium rear alignment motor current switch signal 0: current high front alignment motor current switch signal 0: current high 5-36 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 589 IO-P033 0-7 not used IO-P034 0-7 not used IO-P035 0-7 not used IO-P036 0-7 not used IO-P037 0-7 not used IO-P038 0-7 not used 5-37 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 590 (output) 1 EEPROM/DA clock output (used in common) EEPROM/DA data output (used in common) DA load signal output (used in common) 1: load not used 5-38 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 591 0: ON stapler safety detecting switch signal 1: open front cover open detecting switch signal 1: open joint open detecting switch signal 1: open 5-39 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 592 P028 DIP switch 3, 4 (analog port) P029 DIP switch 1, 2 (analog port) P030 PI10 fold position sensor (light emission; output) (analog port) 5-40 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 593: Puncher Unit (Saddle Finisher-G1)

    0, 1 not used (input) 2 registration interrupt horizontal registration signal H: blocked HFS communication RXD HFS communication TXD (output) not used ACK (output) 5-41 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 594 1 A4 (analog port) P037 horizontal registration sensor light intensity level UP: adjustment intensity increased P038 registration sensor light intensity adjustment level UP: intensity increased 5-42 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 595 CHAPTER 5 SERVICE MODE COPIER>I/O>SORTER delivery motor current switch 1 delivery motor current switch 2 Current (A) (P011-3) (P005-5) T05-301-01 5-43 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 596: Adjust Adjustment Mode

    The following screen will appear in response to COPIER>ADJUST: Function Adjust Counter Display Option Test BLANK ADJ-XY FEED-ADJ LASER HV-PRI CST-ADJ HV-TR MISC DEVELOP DENS F05-401-01 5-44 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 597 1 to 9; default: 5 adjustment Copy density White White Original density A higher setting generates darker text. A lower setting generates darker text. F05-401-02 5-45 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 598 Use it to adjust the CCD read start position (X direction). Range of 100 to 400 (‘1’ being 0.1 mm) adjustment Lower setting Read start position Higher setting Original Vertical size plate F05-401-04 5-46 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 599 Feed direction F05-401-06 STRD-POS Use it to adjust the CCD read position for stream reading. Range of 0 to 60 (‘1’ being 0.1 mm) adjustment 5-47 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 600 (a higher setting increases the time interval up to de-activation) POWER Use it to adjust the laser paper for non-potential control mode. Range of 0 to 255 adjustment 5-48 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 601 • If you have replaced the composite power supply PCB, be sure to enter the settings indicated on the label attached to the new PCB (case). 5-49 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 602 Use it to enter the leading edge non-image width. Range of -100 to +100 adjustment BLANK-B Use it to enter the trailing edge non-image width. Range of -100 to +100 adjustment 5-50 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 603 If you have replaced the composite power supply PCB, be sure to enter the settings indicated on the label attached to the new PCB (case). Range of 0 to 255 adjustment 5-51 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 604 Use it to enter the adjustment value for the primary charging AC component 3 for the image area. Range of 0 to 255 adjustment 5-52 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 605 1st/2nd side of a double- sided print). • A higher setting causes stronger effects. Range of 0 to 10 adjustment 5-53 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 606 0 to 1024 adjustment MF-A6R Use it to enter the paper width basic value for the multifeeder tray (A6R). Range of 0 to 1024 adjustment 5-54 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 607 • Use it to fine-adjust the target control speed for the fixing film when plain paper is selected. Range of -3 to +3 (in msec; default: 0) adjustment 5-55 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 608 • Use it to enter a laser write start position value in relation to the regis- tered value for paper picked up from the multifeeder tray. Range of -32 to +32 (in steps; ‘1’ step being 0.16mm) adjustment 5-56 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 609 PCB to the DC controller PCB. Range of -20 to +20 (in 0.1 mm) adjustment 5-57 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 610: Feeder

    • A higher setting increases the speed. • The data is stored on the ADF controller PCB. Range of -30 to +30 (in 0.1%) adjustment 5-58 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 611: Sorter

    4) Make a print of the Test Chart once again, and check to make sure that the hole position is as indicated. Paper Feed direction Higher setting Lower setting F05-403-01 5-59 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 612 4) Make a print of the Test Chart once again, and check to make sure that the hole position is as indicated. Paper Lower setting Feed direction Higher setting F05-403-02 5-60 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 613: Function Operation/Inspection Mode

    The following screen will appear in response to COPIER>FUNCTION; lists of items fol- low: Function Adjust Counter Display Option Test INSTALL FIXING SYSTEM PANEL PART-CHK DENS CLEAR MISC-R MISC-P F05-501-01 5-61 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 614 Use it to initialize card control information: • initializing the card names (group ID; starting with the entered number). • initializing ID numbers for cards. 5-62 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 615 <OK!>. 5) All items under COPIER>ADJUST>CCD are updated. Record the new settings on the service label. (rear) Standard white paper F05-501-02 5-63 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 616 Thereafter, make a test print to be user that no white line is found in its halftone area. Shading position Vertical size plate Copyboard glass Standard white plate Higher setting Lower setting F05-501-03 5-64 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 617 Does the scanning lamp go ON? 6) The items under COPIER>ADJUST>ADJ-XY and ADJ-S are updated. Record the new settings on the service label. 5-65 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 618 5) The items under COPIER>ADJUST>CCD>EGGN-ST and EGGN- END are updated. Record the new settings on the service label. Edge gain correction plate Copyboard glass Read glass (front) F05-501-04 5-66 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 619 2) See that the machine uses cassette 2 as the source of paper and generate a 17-gradation print pattern. The print pattern will be used when executing <PD-ME>. 5-67 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 620 • If ‘NG’ is indicated, discussed under “Standards and Adjustments” in Chapter 3. Place it so that the printed side faces down. PD-DENS output F05-501-06 5-68 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 621 2) Select <MF-A4R> to highlight, and press the OK key. • The machine executes automatic adjustment and stores the value. 3) Likewise, perform steps 1. and 2. for A6R and A4. 5-69 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 622 - c = 0.5 mm or less F05-501-07 Caution a and b are points 10 mm from both ends of the paper. 5-70 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 623 2) Press the nine +’s that paper on the touch panel in sequence. 3) The machine ends operation when all nine +’s been pressed. 5-71 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 624 Use it to select a motor whose operation you want to check. Using the Mode 1) Select the item. 2) Enter the code (T05-501-03) of the motor using the keypad. 3) Press the OK key. 5-72 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 625 Vertical path clutch (CL1) Multifeeder pickup clutch (CL2) Developing clutch (CL3) Vertical path roller clutch (CL1C) Deck feeding clutch (CL1D) Deck pickup clutch (CL2D) T05-501-02 5-73 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 626 Relay delivery solenoid (SL3Z) Deck pickup roller releasing solenoid Charging roller solenoid (SL6) (SL1D) Multifeeder holding plate Deck open solenoid (SL2D) releasing solenoid (SL5) T05-501-04 5-74 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 627 Using the Mode 1) Select <ERR-HITS> to highlight, and press the OK key. 2) Turn off and then on the main power switch. E345-CLR 5-75 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 628 Use it to clear the alarm log. Using the Mode 1) Select <ALARM> to highlight, and press the OK key. 2) Turn off and then on the main power switch. 5-76 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 629 1) Select <SCANLAMP> to highlight, and press the OK key. 2) The scanning lamp goes ON. 3) Press the Stop key to turn off the lamp. 5-77 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 630 USER MODE: additional function key FNC_COPY: ‘copy’ key within extended keys FNC_FAX: ‘fax’ key within extended keys POWER_MIMI: control panel power key xxxxxxxx function value 5-78 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 631 2) The machine prints a halftone PG image on paper from cassette 4. (At the same time, the horizontal registratoin sensor measures the displacement, and stores the result as back-up data.) 5-79 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 632 1) Select the item, and press the OK key. 2) The pre-exposure lamp goes ON and remains ON for several seconds, and goes OFF automatically. 5-80 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 633 • If’ ‘1’ is selected, the image control data stored in the SRAM area or the general file storage area will also be initialized. Using the Mode 1) Select the item. 2) Press the OK key. 5-81 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 634: Option Machine Settings Mode

    The following screen will appear in response to COPIER>OPTION; lists of items will follow: Adjust Function Counter Display Option Test BODY USER INT-FACE F05-601-01 5-82 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 635 2: fixed mode (for normal humidity) 3: fixed mode (for low humidity) (In 1, 2, or 3, the move of control does not depend on the environment sensor.) 5-83 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 636 0: AB-configuration (default, 1: Inch-configuration, 2: A-configuration) Caution If you have changed the arrangement of the original sensors, select the ap- propriate setting to suit the new arrangement. 5-84 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 637 28 → 15 ppm B5R: from 14 → 10 ppm LGL: A4R,etc.: from 18 → 10 ppm Settings 0: disable (default) 1: enable 5-85 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 638 Use it to indicate the type of software counter 1 of the control panel. Caution The type of soft counter 1 cannot be changed. Settings 101: total 1 (default: fixed to 101) (T05-601-01) 5-86 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 639 Use it to specify whether B4 paper is counted as large-size or small-size for soft counters 1 through 6. Settings 0: small size (default), 1: large size 5-87 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 640 0: disable (original size entered from control panel; default) 1: enable (original size detected automatically) NW-SCAN Use it to enable or disable the network scan function. Settings 0: disable (default), 1: enable 5-88 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 641 (4C/L) S (double-sided) copy (4C/S) copy (total 1) copy (mono/L) copy (total 2) copy (mono/S) copy (L) copy (Bk/L) copy (S) copy (Bk/S) T05-601-01a 5-89 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 642 (4C + mono/L) scan (L) print (4C + mono/S) copy scan (L/4) print (4C + mono/2) scan (S) print (4C + mono/1) copy scan (S/4) T05-601-01b 5-90 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 643 (total 2) color scan (S) report print (L) copy scan (4C/S) report print (S) copy scan (L) copy scan (S) copy scan (total) T05-601-01c 5-91 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 644 However, U2 through U8 size cassettes are designed for specific paper sizes. Settings U2: 35, U3: 25, U4: 31, U5: 32, U6: 34, U7: 22, 29, U8: 23, 30 5-92 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 645 Government LEGAL FOLI FOLIO 11 × 17 11 × 17 A-OFI Argentine OFFICIO LTRR LETTERR M-OFI Mexican OFFICIO LETTER STMT STATEMENT STMTR STATEMENTR T05-601-02 5-93 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 646 • Use it to change the User Mode screen. • Use it to change the network settings. Settings 0: absent (default), 1: external controller present 5-94 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 647: Feeder

    After making a selection, be sure to turn off and then on the main power switch. Settings 0: disable retraction movement (default), 1: enable detraction move- ment 5-95 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 648 Use it to enable or disable the function of slot 3 when the board in slot 3 of PCI is out of order. Settings 0: normal (default), 1: disable (not to use board function) 5-96 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 649: Test Test Print Mode

    7 TEST Test Print Mode The following screen will appear in response to COPIER>TEST; lists of items will fol- low: Function Counter Adjust Test Display Option NETWORK F05-701-01 5-97 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 650 (normal print) halftone grid solid black 17 gradations vertical straight lines (w/ image correction) horizontal straight lines 17 gradations (w/o image correction) T05-701-01 5-98 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 651 • If ‘NG’ is indicated, check the connection for the network cable; if nor- mal, go to step 6). If a fault is found, connect the cable correctly, and go to step 5). 5-99 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 652 In this case, the user’s network may have a problem. Report to the system administrator for corrective action. 5-100 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 653: Counter Counter Mode

    The counter will be cleared, and it will read ‘00000000’. Dividing Papers Between Small-Size and Large-Size Large-size (L): lager than A4/LTR Small-size (S): A4/LTR or smaller 5-101 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 654 RMT-PRT remote copy/print counter BOX-PRT Box print counter RPT-PRT repro print counter 2-SIDE double-sided print counter SCAN scan counter 5-102 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 655 1 jam counter cassette 2 jam counter cassette 3 jam counter cassette 4 jam counter paper deck jam counter 5-103 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 656 PD-SP-RL paper deck separation roller counter PD-FD-RL paper deck feeding roller counter FIN-STPR stapler counter SDL-STPL saddle stapler counter PUNCH punch counter 5-104 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 657: Chapter 6 Self Diagnosis

    CHAPTER 6 SELF DIAGNOSIS COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 659 The following tables show the codes used, timing of detection, and possible causes; a 4- digit code is a detail code, and may be checked in service mode (COPIER>DISPLAY>JAM/ ERR). 6-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 660 E537 Front alignment motor E712 Communication error (with ADF) E577 Delivery motor E713 Communication error (with sorter E580 Delivery tray ascent/descent motor finisher) E585 Stack handling error 6-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 661: Detail Codes (Copier)

    YES: The heater drive power supply is faulty. Replace the main power supply PCB. The thermistor control mechanism is faulty. Replace the DC con- troller PCB. 6-3 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 662 2. Main power supply PCB, DC controller PCB Try replacing the main power supply PCB. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-4 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 663 3. Fixing film unit, DC controller PCB Try replacing the fixing film unit. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-5 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 664 3. Fixing film unit, DC controller PCB Is there a fault in the fixing film edge rotation detection mechanism? YES: Replace the fixing film unit. Replace the DC controller PCB. 6-6 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 665 J308 on the DC controller PCB? Lock signal: J318-A10 (MM_LOCK) YES: Replace the main motor. Check the wiring; if normal, replace the DC controller PCB. 6-7 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 666 Lock signal: J312-B4 (FSRM_LOCK*) the DC controller PCB change from 0 to about 5 V? YES: Replace the fixing motor. Replace the DC controller PCB. 6-8 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 667 2. Waste toner full sensor, DC Controller PCB Try replacing the waste toner case full sensor. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-9 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 668 Connect it securely. 2. DA controller, Main controller PCB Try replacing the DA unit. Is the problem corrected? YES: End. Replace the main controller PCB. 6-10 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 669 PCB? J304-1/2: 24 V, J304-3/4/5/6: motor excitation signal YES: The horizontal registration motor is faulty. Replace the motor. Replace the DC controller PCB. 6-11 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 670 3. Composite power supply PCB, DC controller PCB Try replacing the composite power supply PCB. Is the problem corrected? YES: Yes. Replace the DC controller PCB. 6-12 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 671 2. Laser scanner unit, DC controller PCB Try replacing the laser scanner unit. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-13 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 672 3. Laser scanner unit, DC controller PCB Try replacing the laser scanner unit. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-14 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 673 2. ADF controller PCB, Reader controller PCB Try replacing the ADF controller PCB. Is the problem corrected? YES: End. Replace the reader controller PCB. 6-15 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 674 Replace the scanning lamp. 2. CCD unit, Reader controller PCB Try replacing the CCD unit. Is the problem corrected? YES: End. Replace the reader controller PCB. 6-16 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 675 2. Control panel CPU PCB, Main controller PCB Try replacing the control panel CPU PCB. Is the problem corrected? YES: End. Replace the main controller PCB. 6-17 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 676 2. Main power supply PCB, Main controller PCB Try replacing the main power supply PCB. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-18 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 677 3. Reader controller PCB, Main controller PCB Try replacing the reader controller PCB. Is the problem corrected? YES: End. Check the wiring; if normal, replace the main controller PCB. 6-19 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 678 Further, if this error occurs in a specific image within the MAIL BOX, damage in data may be assumed; be sure to delete the image from the MAIL BOX. 6-20 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 679 2. DC controller PCB, Main controller PCB Try replacing the DC controller PCB. Is the problem corrected? YES: End. Replace the main controller PCB. 6-21 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 680 A fault is detected in the battery for the image memory. Main cause The wiring is faulty (short circuit, open circuit). The HDD is faulty. The main controller PCB is faulty. 6-22 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 681 Correct the connection and the cable. 2. FAX PCB, Main controller PCB Try replacing the FAX PCB. Is the problem corrected? YES: End. Replace the main controller PCB. 6-23 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 682 Correct the connection. 2. Printer board, Main controller PCB Try replacing the printer board. Is the problem corrected? YES: End. Replace the main controller PCB. 6-24 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 683 Turn off and then on the main power switch. Is the problem corrected? YES: End. If E7100001, replace the reader controller PCB. If E710-002, replace the DC controller PCB. If E71-0003, replace the main controller PCB. 6-25 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 684 Is the interface cable between the DA unit PCB and the main controller PCB normal? Correct the cable. YES: Replace the NE controller PCB. 6-26 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 685 3. ADF controller PCB, Reader controller PCB Try replacing the ADF controller PCB. Is the problem corrected? YES: End. Replace the rear controller PCB. 6-27 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 686 3. Finisher controller PCB, DC controller PCB Try replacing the finisher controller PCB. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-28 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 687 2. DA unit PCB, main controller PCB Try replacing the DA unit PCB. Is the problem corrected? YES: End. Replace the main controller PCB. 6-29 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 688 Is the connection between the connector J1014 on the main controller PCB and the connector J409 on the reader controller PCB normal? Correct the connection. YES: Replace the reader controller PCB. 6-30 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 689 Fit the DRAM securely. 2. DRAM, Main controller PCB Try replacing the DRAM. Is the problem corrected? YES: End. Replace the main controller PCB. 6-31 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 690 Correct the connection. 2. Relay board, Main Controller PCB Try replacing the relay board. Is the problem corrected? YES: End. Replace the main controller PCB. 6-32 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 691 Making Corrections Downloading (system software) Check the types of the BootROM and the system software, and download system software of the correct type. 6-33 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 692 (J204-5 <-> J300-5: OVU3, J204-6 <-> J300-6: OVU3, J204-7 <-> J300-7: 24VU3, J204-8 <-> J300-8: 24VU3) Replace the main power supply PCB. YES: Replace the DC controller PCB. 6-34 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 693 Correct the wiring and the connection. 3. Fan, DC controller PCB Try replacing the fan. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-35 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 694 4. Pedestal controller PCB, DC controller PCB Try replacing the pedestal controller PCB. Is the problem corrected? YES: End. Replace the DC controller PCB. 6-36 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 695 0.5 sec or more. Main cause The IPC communication is faulty. The communication line has an open cir- cuit. The ADF controller PCB is faulty. 6-37 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 696 2 sec. Main cause The feed motor (M1) is faulty. The setting roller home position sensor is faulty. The finisher controller PCB is faulty. 6-38 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 697 4.5 sec. Main cause The slide home position sensor PI180 is faulty. The stapler slide motor (M8) is faulty. The finisher controller PCB is faulty. 6-39 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 698 The paddle home position sensor (PI2) is faulty. The stack ascent/descent home point sensor Pixx0 is faulty. The paddle motor (M2) is faulty. The fin- isher controller PCB is faulty. 6-40 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 699 Main cause The horizontal registration home position sensor (PI2P) is faulty. The puncher shift motor (M2P) is faulty. The puncher drive PCB is faulty. 6-41 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 700 The folding roller home position sensor (PI12) is faulty. The stapler/folder motor (M7) is faulty. The stapler/folder clock sensor (PI14) is faulty. The finisher controller PCB is faulty. 6-42 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 701 The rear alignment motor (M4) is faulty. The rear aligning plate home posi- tion sensor (S7) is faulty. The rear alignment motor relay harness is faulty. The rear aligning plate is subjected to an excess load. 6-43 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 702 (S3) is faulty, the harness connector is discon- nected, or an open circuit exits. The delivery motor relay harness is faulty. The return roller is faulty. 6-44 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 703 (S8) is faulty, the connector is disconnected, or an open circuit exits. The stack handling motor (M2) relay harness is faulty. The return roller is faulty. 6-45 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 705: Chapter 7 Upgrading

    CHAPTER 7 UPGRADING COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 707: Upgrading

    2) Hold down ‘2’ and ‘8’ on the keypad until the bottom of the touch panel indicates the message “Download Mode.” Partition Available for Formatting the Hard Disk /BOOTDEV 7-1 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 708 Connect the machine with the PC using a cross Ethernet cable or a straight Ethernet cable and a HUB. The following shows how a cross Ethernet cable may be used. Cross Cable F07-101-01 7-2 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 709 If you are using a straight Ethernet cable and a HUB, you are encouraged to connect the machine with the PC on a one-on-one basis, outside the user’s network environment. Straight Cable Straight Cable F07-101-02 7-3 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 710 If both are in use, you must turn the machine off and then on first before making a switch-over (i.e., from Bi-Centronics to Network or vice versa), thereby preventing errors in the event of simultaneous writing operations. 7-4 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 711: Data Control

    You must install the files to use (System, RUI, HD Format , BOOT, Language) before ex- ecuting downloading. 1) Start up the Service Support Tool. 2) Under ‘Controlling Data’, select ‘To Next’. F07-102-01 7-5 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 712 3) From the Control Work screen of the firmware, select ‘Registering Firmware’. F07-102-02 4) From the following screen, select ‘Register from selected folder’. F07-102-03 7-6 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 713 On this screen, it is in the case of iR8500. F07-102-04 Note: For iR2800/iR3300 User You must select the folder of iR2200. Such software can be used in common. 7-7 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000...
  • Page 714: Making Connections

    4) Connect the machine’s power plug to the power outlet, and turn on the main power switch. 1.3.2 Downloading 1) Under ‘Downloading/Uploading’, select ‘To Next’. F07-103-01 7-8 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 715 ‘E744-0001’ will be indicated when the machine is started up for the first time; to reset the error, install a module of the correct version. 7-9 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 716 Change screen. Select ‘High-Speed’, and press ‘OK’ to move to step 6). High-speed mode is not supported on Windows NT and Windows 2000. Memo F07-103-04 7-10 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 717 CHAPTER 7 UPGRADING 6) Click ‘OK’ to start connection. F07-103-05 7) When connection is done, the following screen will appear. Click ‘OK’. F07-103-06 7-11 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 718 9) Select the files suited to the language and the country in question from the ‘list of soft- ware’ on the Service Support Tool screen, and click ‘Start’. F07-103-08 7-12 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 719 11) Check the progress bar, which indicates the progress of downloading. 12) When downloading ends, turn off the PC by making the following selections: OK>To Unit Selection Screen>OK>To Main Menu>Ending the Service Support Tool>End. 7-13 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 720: After Downloading

    On this screen, it is in the case of iR8500. • The model of the machine is the same; e.g., you cannot use the iR2200 BOOT ROM data to upgrade an iR5000. • The parameter “function” (COPY or PRINTER) must match when down- loading the system software;...
  • Page 721: Connection

    ‘OK’ so that the machine will be in download standby mode (notation “STNDBY”). 1.4.3 Preparing BOOT ROM The discussions that follow assume upgrading an iR8500 (COPY model). 1) User ‘Downloading/Uploading’, select ‘To Next’. F07-104-01 7-15 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 722 BOOT, and Network is selected for Interface.) F07-104-02 3) To enter the IP address or the host name of the machine to connect, click ‘Set host name’. F07-104-03 7-16 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 723 5) Check to see that the notation in the upper right indicates the IP address or the host name of the machine to connect; then, click ‘OK’ to start connection. F07-104-05 7-17 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 724 6) When connection is done, the following screen appears. Click ‘OK’. F07-104-06 7) Select ‘BOOT ROM Download’ on the Service Support Tool screen. F07-104-07 7-18 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 725 4) If a network cable is connected, connect it to the correct location, and turn on the machine’s main power switch. 5) When the machine has started up, start service mode, and check the version of the BOOT ROM: COPIER>DISPLAY>VERSION>BOOT-ROM. 7-19 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 726: Formatting The Hdd

    3) Connect the machine’s power plug to the power outlet; while holding down ‘2’ and ‘8’ of the keypad at the same time, turn on the main power switch. 1.5.2 Starting Formatting 1) Under ‘Downloading/Uploading’, select ‘To Next’. F07-105-01 7-20 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 727 3) At this time, if the notation in the upper right of the screen is ‘High-Speed’, go to step 5); if ‘Low-Speed’, go to step 4). F07-105-03 7-21 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 728 4) Click ‘change operation mode’ so that the Centronics Communication Mode change screen will appear. Select ‘high-speed’, and click ‘OK’; then, go to step 6). F07-105-04 5) Click ‘OK’ to start connection. F07-105-05 7-22 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 729 CHAPTER 7 UPGRADING 6) When connection is done, the following screen will appear. Select ‘OK’. F07-105-06 7) When the Check screen appears, select ‘Format’. F07-105-07 7-23 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 730 8) When the Start Check screen appears, select ‘Start’ to format all partitions. F07-105-08 9) When the Start Check screen appears once again, select ‘Start’. F07-105-09 7-24 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 731 10) When formatting is done, the message “Format Finished” appears. Click ‘OK’. F07-105-10 11) To continue downloading system, select ‘To Unit Selection Screen’, and click ‘OK’. Then, start downloading system. F-07-105-11 7-25 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 732 This is a normal condition, and will disappear when you turn off and then on the machine twice. 7-26 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 733: Downloader Pcb

    Connects the downloader PCB and the option's PCB to each 50 cm long) other. RS-232C connector Connects the RS-232c cable to the downloader PCB. T07-106-01 7-27 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 734: Download Procedure

    PC side. 5) Turn on the copier. The power indicating LED on the PCB light. 7-28 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 735 2) Choose “Downloading/Uploading.” F07-106-03 3) Press the START/STOP key. The LOAD LED lights. 4) Choose suitable folder. Highlight the model name and click Connect. (ex.DADF-H1) F07-106-04 7-29 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 736 5) Get ready for downloading as instructed on the screen. Click OK to proceed further. F07-106-05 6) Choose the ROM version to download. F07-106-06 7-30 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 737 7) Click START to let the PC and the downloader PCB to start downloading the program. F07-106-07 8) Click OK when the download completes. F07-106-08 7-31 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 738: Disconnecting

    2) Turn off the copier. 3) Disconnect cable B from the finisher or ADF. 4) Reattach the cover to the finisher or ADF. 5) Turn on the copier 7-32 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 739 The BOOT ROM [3] on the main controller PCB may be upgraded using a PC. For details, see the descriptions under 1.4 “Upgrading the BOOT Memo ROM.” F07-107-01 7-33 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 740: Outline

    It is recommended to back up the data whenever possible using the Service Support Tool when you have updated the service mode settings or the user mode settings. 7-34 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 741: Making Preparations

    5) Make the following selections so that the machine will enter download standby mode (notation “STNDBY”): COPIER>FUNCTION>SYSTEM>DOWNLOAD. You can select ‘network’ as the interface for data backup. Here, the use of a bi-Centronics cable is assumed. Memo 7-35 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 742 1) Under ‘Downloading/Uploading’, select ‘To Next’. F07-202-01 2) Select ‘SYSTEM’, and select ‘Connect’. The discussions that follow assume the use of a bi-Centronics cable as the interface. F07-202-02 7-36 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 743 4) Click ‘Switch operation mode’ to bring up the Centronics Communication Mode Change screen. Select ‘High-Speed’, and click ‘OK’ to move to step 5). F07-202-04 7-37 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 744 CHAPTER 7 UPGRADING 5) Click ‘OK’ to start connection. F07-202-05 6) When connection is done, the following screen appears. Click ‘OK’. F07-202-06 7-38 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 745 CHAPTER 7 UPGRADING 7) Select ‘Upload the Backup Data’ on the Service Support Tool screen. F07-202-07 8) Select ‘ALL’, and select ‘Start Storing’. F07-202-08 7-39 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 746 11) When the selected file has been stored on the selected drive, the following screen will appear; make the following selections to end the Service Support Tool: OK>To Unit Se- lection Screen>OK>To Main Menu>Ending the Service Support Tool>End. F07-202-10 7-40 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 747 CHAPTER 7 UPGRADING 2.2.4 Downloading Backup Data 1) Under ‘Downloading/Uploading’, select ‘To Next’. F07-202-11 2) Select ‘SYSTEM’, and select ‘Connect’. F07-202-12 7-41 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 748 CHAPTER 7 UPGRADING 3) Select ‘OK’, and start connection. F07-202-13 4) When connection is done, the following screen appears. Click ‘OK’. F07-202-14 7-42 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 749 CHAPTER 7 UPGRADING 5) Select ‘Download the backup Data’. F07-202-15 6) Select the file to download, and select ‘Start Writing’. F07-202-16 7-43 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 750 Select ‘OK’. F07-202-17 8) Make the following selections to end the Service Support Tool: To Unit Selection Screen>OK>To Main Menu>Ending the Service Support Tool>End. 7-44 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 751 You need not connect a PC to the machine to do so. 1) Under ‘Controlling Data’, select ‘To Next’. F07-202-18 2) Select ‘Controlling Backup Data’. F07-202-19 7-45 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 752 3) Select the file to delete from the list of ‘Backup Data Stored on Computer’; then select ‘Remove’. F07-202-20 4) When the Delete Check screen appears, check the description for the selected file, and select ‘Remove’. F07-202-21 7-46 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 753 5) When the Delete Finish screen appears, click ‘OK’. Make the following selections to end the Service Support Tool: Return to Previous Screen>Return to Main Menu>Ending the Service Support Tool>End. F07-202-22 7-47 T COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 755 APPENDIX COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 757 Fixing film sensor (PS26) *1: Varies between 0 and 9 min to suit the selected silent mode shift interval. *2: Goes ON once every 540 msec. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 758 Pickup motor (M2) Main motor (M1) Pickup DOWN solenoid (SL1) Scanner home position sensor (PS400) Scanning lamp (LAMP1) Scanner motor (M400) Print command sent :motor CCW. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 759 Multifeeder paper width sensor 18-M To FAX Unit Cassette2 paper level sensor 1 20-M ( 1 0 0 V O N LY ) Cassette2 paper level sensor 2 20-M COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 761 Deck open solenoid SW100D Deck open switch 13-A SW1D Deck open detecting switch Deck lifter lower limit detecting switch SW2D Side deck drier PCB LED100D SW100D COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 762 Cassette4 paper level sensor0 Q1609 Cassette4 paper level sensor1 Cassette3 size detecting switch Cassette4 size detecting switch SL1C 11-F Pickup roller DOWN solenoid (Q1603,1605-1609) Pedestal controller PCB COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 763: Inner 2-Way Tray-A1 General Circuit Diagram

    2-way delivery outlet motor PS19B No.2 delivery sensor PS20B No.2 delivery full sensor PS21B No.3 delivery sensor PS24B 2-way delivery open/closed sensor SL3B 2-way delivery solenoid COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 764: List Of Special Tools

    No. 1/No. 2 mirror. (front, rear) NA-3 Test Sheet FY9-9196 Used when adjusting/ checking images. Tester extension FY9-3038 Used when making electrical checks. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 765 A: each service person is expected to carry one. B: each group of five persons is expected to carry one. C: each workshop is expected to carry one. COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 766: List Of Solvents/Oils

    Tool No.: CK-0524 (100cc) Lubricant Lubrication: drive Silicone oil parts, friction parts Tool No.: CK-0551 (20g) Lubricant Lubrication: scanner Silicone oil rail Tool No.: FY9-6011 (50cc) A-10 COPYRIGHT © 2001 CANON INC. 2000 2000 2000 2000 CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001...
  • Page 767 Prepared by Office Imaging Products Quality Assurance Center CANON INC. Printed in Japan REVISION 0 (MAR. 2001) (18723/18756/22109/32205/35338) 5-1, Hakusan 7-chome, Toride-shi, Ibaraki 302-8501 Japan COPYRIGHT© 2001 CANON INC. CANON iR2200/iR2800/iR3300 REV.0 MAR. 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
  • Page 768 This publication is printed on 100% recycled paper. PRINTED IN JAPAN (IMPRIME AU JAPON) 0401M0.7-1...

This manual is also suitable for:

Ir2800Ir3300

Table of Contents