hit counter script
Panasonic CT-32G6E Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. TV
  5. CT32G6E - 32" COLOR TV
  6. Service manual

Panasonic CT-32G6E Service Manual

Color television
Hide thumbs Also See for CT-32G6E:
Table of Contents

Advertisement

Quick Links

Service Manual

This Service manual is issued as a service guide for the models of the NA7D family listed above. Included are
schematics, alignment procedures, disassembly procedures, and a parts list.
"WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death."
The service technician is required to read and follow the "Safety Precautions" and "Important Safety Notice" in this Manual.
Color Television
Main Manual
(NA7D)
Panasonic
Models
CT-32G6E
CT-32G6CE
CT-32G6UE
Copyright 2001 by Matsushita Electric Corporation of
America. All rights reserved. Unauthorized copying
and distribution is a violation of law.
ORDER NO. MTNC010414C1
B5
Chassis
AP364
AP364
AP364

Advertisement

Table of Contents
loading

Related Manuals for Panasonic CT-32G6E

Summary of Contents for Panasonic CT-32G6E

  • Page 1: Service Manual

    Service Manual Color Television Main Manual (NA7D) Panasonic Models Chassis CT-32G6E AP364 CT-32G6CE AP364 CT-32G6UE AP364 This Service manual is issued as a service guide for the models of the NA7D family listed above. Included are schematics, alignment procedures, disassembly procedures, and a parts list.

  • Page 2: Important Safety Notice

    Important Safety Notice Special components are used in this television set which are important for safety. These parts are identified on the schematic diagram by the symbol and printed in BOLD TYPE on the replacement part list. It is essential that these critical parts are replaced with the manufacturer’s specified replacement part to prevent X-ray radiation, shock, fire or other hazards.

  • Page 3: Table Of Contents

    Corrector Strip ....12 CT-32G6E/CE/UE....38 Service Mode A-Board Voltages.

  • Page 4: Service Notes

    Service Notes Note: Some components may be affixed with glue. Be careful not to break or damage foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.

  • Page 5: X-Ray Protection Circuit Check & Adjustments

    IMPORTANT: To protect against possible damage to X-Ray Protection Circuit Check & the solid state devices due to arcing or static Adjustments discharge, make certain that all ground wires and CRT This test must be performed as final check before the DAG wire are securely connected.

  • Page 6: Receivers Feature Table

    Specifications are subject to change without notice or obligation. Dimensions and weights are approximate. * Note: When ordering a replacement board assembly, append an “S” to the board number. Example: to order the A-Board for CT-32G6E, the replacement board is TNP2AH024ABS. - 6 -...

  • Page 7: Location Of Receiver Controls

    Location of Receiver Controls Figure 2. Location of Controls. Quick Reference Control Operation Power Button - Press to turn ON or OFF. Volume Buttons - Press to adjust Sound Level, or to adjust Audio Menus, Video Menus, and select operating features when menus are displayed. Channel Buttons - Press to select programmed channels.

  • Page 8: Location Of Controls

    Location of Controls POWER MUTE Press to mute sound. Press to Press to turn ON and OFF. access and cancel (CC) Closed Caption. Press to adjust TV sound and navigate in menus. Press to select next channel and navigate in menus. ACTION Press to access menus.

  • Page 9: Disassembly For Service

    Disassembly for Service Back Cover Disassembly for CRT Replacement 1. Discharge the CRT as instructed in the Safety Remove all the screws marked with an arrow( Precautions (see page 2). from the back of the Receiver. 2. Disconnect the yoke (DY) plug, degaussing coil Note: Screw configuration, type, and number of (DEG) plug from the main board.

  • Page 10: Chassis Service Adjustment Procedures

    Chassis Service Adjustment Procedures Note: Connect the (-) lead of the voltmeter to the All service adjustments are factory preset and should require adjustment unless controls and/or appropriate ground. Use IC801’s heat sink associated components are replaced. when the HOT ground symbol ( ) is used. Otherwise, use COLD ground ( ) —...

  • Page 11: Purity Convergence Procedure

    Purity and Convergence Procedure Adjustment is necessary only if the CRT or the results, note part number and look for specifications at deflection yoke is replaced or if the setting was Service Center) disturbed. The complete procedure consists of: 1. Vertical Raster Shift Adjustment. (Only for Models with Purity/Convergence Assembly with 4 Pairs of Rings).

  • Page 12: Purity Adjustment

    Purity Adjustment Final Convergence Procedure (see Fig. 11 When the Receiver is in the Service Mode for making through Fig. 13) electronic adjustments, press the Recall button on the Note: Vertical size and focus adjustments must be Remote Control to enter Purity Check. (See the completed prior to performing the convergence Service Adjustments Electronic Controls procedure).
  • Page 13 Figure 11. Vertical Yoke Movement Figure 12. Horizontal Yoke Movement Figure 13. Convergence Magnets and Wedges Location Note: For models using 4 pairs of rings assemblies see Fig. 6 for details - 13 -...

  • Page 14: Service Mode (Electronic Controls)

    Service Mode (Electronic Controls) This Receiver has electronic technology using the I²C Bus Concept. It performs as a control function and it replaces many mechanical controls. Instead of adjusting mechanical controls individually, many of the B 00 33 C 00 0 255 control functions are now performed by using “On Screen Display Menu”.
  • Page 15 Press the POWER Button on the Remote Control to select the Service Adjustment. For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 14 ) for Remote Control to adjust the the available Service Adjustments each...
  • Page 16 Default Cut-Off Adjustment Level ACL-COEF-factory preset ACL-COEF-factory preset ACL-WAIT-factory preset ACL-THRESHOLD-factory preset MACROVISION-factory preset OSD SELECT-factory preset KILLER ON-factory preset KILLER OFF-factory preset KILLER TIME-factory preset ACC THRESHOLD-factory preset ACC OFF-factory preset MUTE TIME-factory preset Default MTS Adjustment Level INPUT HIGH-LEVEL SEPARATION LOW-LEVEL SEPARATION AGC ADJ-factory preset...
  • Page 17 Default VCJ Adjustment (Continued) Level ACC AMP ON-factory preset ACC AMP CTL-factory preset BGP POSITION-factory preset OSD R-factory preset OSD G-factory preset OSD B-factory preset NOISE KILLER TIME-factory preset NOISE KILLER (ACC)-factory preset HV TIMING-factory preset Default VCJ Adjustment (Black Expansion) Level FORCE BS-factory preset DET ON/OFF-factory preset...
  • Page 18 Default Other Adjustment Level AFCT AFCB AFCC CLOCK TO B ITEMS To Check Purity: When Receiver is in Service Mode (red “CHK” is Note: if jumper is not removed, colors will be displayed displayed), place a jumper in the AG connector at high luminosity.
  • Page 19 Notes: - 19 -...

  • Page 20: Instructional Flow Chart For Service Mode

    Instructional Flow Chart for Service Mode IMPORTANT Always Exit the Service Mode Following Adjustments. NORMAL MODE Momentarily short FA1 to FA2 ( AGING MODE • Yellow “CHK” appears in upper left corner of screen. WHITE • Volume Up/Down operate rapidly. SCREEN •...
  • Page 21 CUT-OFF ADJUSTMENTS. C ITEMS. ON REMOTE CONTROL TO Adj. SELECT ADJUSTMENT needed? ON REMOTE TO ADJUST VOL VOL THE LEVEL POWER (ON REMOTE) M, S, P & X Adjustments procedures are similar to the B Adjustments. ON REMOTE CONTROL TO Adj.

  • Page 22: Service Adjustments

    Service Adjustments (Electronic Controls) Note: It is recommended to allow for a 30 minute Tint/Color Adjustment warm up period, at high brightness level (use Service DAC Adjustment (B1) (B0) white screen), prior to any picture adjustment. Preparation: 1. Apply a rainbow color bar signal. Sub-Contrast 2.

  • Page 23: White Balance

    • C5: Drive_B ..80 White Balance Touch-Up Procedure: 3. Confirm using Black & White pattern and a white Use this procedure to make minor adjustment to white screen the color balance (gray scale and white balance.

  • Page 24: Vertical Size

    Stereo Separation Adjustment (M1 & M2) Preparation: 1. Connect an RF signal generator to the RF antenna input. 2. Connect a scope to TPE10. Procedure: 1. Select Stereo Mode in Audio menu 2. Apply the following signal from the RF signal generator: Video: 100 IRE flat field, 30% modulation.

  • Page 25: Service Adjustments (Mechanical Controls)

    Service Adjustments (Mechanical Controls) Focus (part of T551) Preparation: Connect a Signal generator and select a dot pattern. Procedure: Adjust the FOCUS control VR to obtain the sharpest and clearest dot pattern. a. Adjust for best center. b. Adjust for best area between the center and top right corner.

  • Page 26: Component Identification

    Identification of Components Screw Screw Screw Screw Screw Screw Screw Screw Figure 26. Back Cover Removal (CT-32G6E/CE/UE) CRT (secured to cabinet by 4 Anode (high voltage) screws on corners of CRT) C board Yoke DAG ground Degaussing coil Speaker (4 screws)
  • Page 27 CRT Socket Q352 G Out Q353 Q351 B Out R Out Figure 28. C-Board component locations Figure 29. Z-Board - 27 -...
  • Page 28 IC050 Halftone IC001 MPU/VCJ Components on trace side IC003 Remote Sensor IC801 IC002 IC451 EEPROM Vertical Out D801 Rect Bridge Q501 H-Drive IC005 3.3 V IC551 IC2301 9V Reg Right IC552 Audio Q551 5V Reg H-Out S-VHS RL801 TNR001 A/V Jacks Relay Tuner Flyback...

  • Page 29: Parts List

    REPLACEMENT PARTS LIST Models: CT-32G6E/CE/UE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...

  • Page 30: Replacement Parts List

    REPLACEMENT PARTS LIST Models: CT-32G6E/CE/UE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 31 REPLACEMENT PARTS LIST Models: CT-32G6E/CE/UE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 32 REPLACEMENT PARTS LIST Models: CT-32G6E/CE/UE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 33 REPLACEMENT PARTS LIST Models: CT-32G6E/CE/UE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...

  • Page 34: Components Abbreviations Guide

    DESCRIPTION REF NO. PART NO. DESCRIPTION ASSY, CABINET FRONT M017 TKX2A3753 GUIDE, IR M011 TXFKY10ESER Badge Panasonic, Guide IR, Cab. Front JK3001 TJB2A9064B ASSY, JACK A/V 32”, Smoked Sheet, Pad Foam JK3003 TJB2AA0171 TERMINAL, S-VHS ASSY, CABINET BACK M012 TXFKU15ESER...

  • Page 35: Schematic Notes

    General Notes IMPORTANT SAFETY NOTICE CHIP TRANSISTOR THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL LEAD DESIGNATION FEATURES THAT ARE IMPORTANT FOR PROTECTION FROM X-RADIATION, FIRE AND ELECTRICAL SHOCK HAZARDS. WHEN SERVICING ESSENTIAL THAT ONLY MANUFACTURERS SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS DESIGNATED WITH A IN THE SCHEMATIC.
  • Page 36 General Notes NOTA DE SEGURIDAD DIAGRAMAS ELÉCTRICOS INCLUYEN CARACTERÍSTICAS ESPECIALES MUY IMPORTANTES IDENTIFICACIÓN DE TERMINALES PARA TRANSISTORES EN CHIP PARA PROTECCIÓN CONTRA RAYOS-X, QUEMADURAS Y DESCARGAS ELÉCTRICAS. CUANDO SERVICIO IMPORTANTE USAR PARA REEMPLAZO COMPONENTES CRITICOS, SOLO PARTES ESPECIFICADAS POR EL FABRICANTES. LOS COMPONENTES CRITICOS ESTAN SEÑALADOS EN LOS DIAGRAMAS POR EL SIMBOLO NOTAS DE LOS DIAGRAMAS...

  • Page 37: C-Board Schematic

    C-BOARD SCHEMATIC, LAYOUT & VOLTAGES -- DIAGRAMA ELÉCTRICO, CIRCUITO IMPRESO Y VOLTAJES TARJETA C C-BOARD -- TARJETA C Notes: • Check Parts List for most recent component values and part numbers. • Obtain voltages with a digital multimeter. • The board layouts were modified to enhance and display traces otherwise hidden by a mask.

  • Page 38: Ct-32G6E/Ce/Ue

    A-BOARD SCHEMATIC LEFT PORTION -- DIAGRAMA ELÉCTRICO TARJETA A SECCIÓN IZQUIERDA A-BOARD -- TARJETA A - 38 -...
  • Page 39 A-BOARD -- TARJETA A A-BOARD SCHEMATIC RIGHT PORTION -- DIAGRAMA ELÉCTRICO TARJETA A SECCIÓN DERECHA CHIP TRANSISTOR LEAD DESIGNATION IDENTIFICACIÓN DE TERMINALES PARA TRANSISTORES EN CHIP - 39 -...

  • Page 40: A-Board Voltages

    A-BOARD -- TARJETA A A-BOARD VOLTAGES -- VOLTAJES TARJETA A IC001 IC002 IC050 IC551 IC2201 IC2301 ..GND ..GND ..GND ..2.59 .

  • Page 41: Waveforms

    WAVEFORMS -- FORMAS DE ONDA A-BOARD WAVEFORMS -- FORMAS DE ONDA TARJETA A All Models -- To- dos los Modelos CHIP TRANSISTOR LEAD DESIGNATION 1.3V p-p [20µs] 1.7V p-p [20µs] 1.9V p-p [5ms] 3.1V p-p [20µs] 3.2V p-p [5µs] TPA5 (VIDEO) (R OUT) IC001 PIN 43 (FB PULSE) IC451 PIN 7 (DRIVE)

  • Page 42: A & C-Boards Layouts

    A & C-BOARDS -- TARJETAS A Y C A & C-BOARDS LAYOUT -- CIRCUITO IMPRESO DE LAS TARJETAS A Y C - 42 -...

  • Page 43: Z-Board Schematic

    Z-BOARD SCHEMATIC, LAYOUT & VOLTAGES Z-BOARD - TARJETA Z DIAGRAMA ELÉCTRICO, CIRCUITO IMPRESO Y VOLTAJES TARJETA Z Q751 Q752 Q753 2.97 12.49 0.45 9.75 0.40 11.66 2.38 12.98 - 43 -...
  • Page 44 NOTES -- NOTAS - 44 -...
  • Page 45 Notes: - 45 -...
  • Page 46 Notes: - 46 -...

  • Page 47: Service Mode Adjustments

    SERVICE MODE (ELECTRONIC CONTROL) SERVICE ADJUSTMENT VALUES Model _____________________________________________ Ser #_____________ Date_________________ Note: Record the original settings PRIOR to modifying the registers. Service Adjustment Def. Original Service Adjustment Def. Original Mode Mode Adjustment Range Val. Value Value Adjustment Range Val. Value Value Cut-Off Adjustments, Cont.
  • Page 48 SERVICE MODE, CONT. (ELECTRONIC CONTROL) SERVICE ADJUSTMENT VALUES Model _____________________________________________ Ser #_____________ Date_________________ Note: Record the original settings PRIOR to modifying the registers. Service Adjustment Def. Original Service Adjustment Def. Original Mode Mode Adjustment Range Val. Value Value Adjustment Range Val.

This manual is also suitable for:

Ct-32g6ceCt-32g6ueAp364

Table of Contents