Advertisement
Quick Links
Download this manual
See also:
User Manual
Day/Night Ultra Wide Dynamic Fixed Dome Camera
Quick Install Guide
Thank you for purchasing a Honeywell Day/Night Ultra Wide Dynamic Fixed Dome
Camera. Before installing the camera, please verify your model and read this guide
carefully:
Model
Signal format
Lens
HD4U
NTSC
2.8 to 10 mm Vari-focal Auto Iris lens
HD4UX
PAL
2.8 to 10 mm Vari-focal Auto Iris lens
Unpack Everything
HD4U/X Camera
+ factory-installed pigtail power and video
connectors
+ wall mount adapter plate
This guide
Mounting template
Hardware Kit
You will also require a Phillips screwdriver and side-cutters.
Mount the Camera (cont'd)
Electrical Box Installation (4S Shown)
Ceiling/wall
Document 800-00032 – Rev B – 04/08
1
3
Electrical box
(not supplied)
4S electrical box: Secure the
adapter plate using appropriate
screws (not supplied)
Double/Single Gang electrical box:
Adapter plate not required.
HD4U base
Secure the base with screws
appropriate to your installation
(not supplied)
#6- 1 7/16 Inch slotted Type A
screws (surface mount without
electrical box)
Prepare for Installation
1.
Use the mounting template to mark and pre-drill the holes.
2.
Connect the cables:
Through the grommet in the housing base
a.
Use a sharp knife to cut an opening in the
base gasket ! only large enough to feed
the cable assembly through.
b.
Apply sealant around the opening.
Through the side conduit
c.
Peel back the bottom flat gasket below the
side conduit to expose the security screw.
d.
Use the Allen key to remove the security
screw.
e.
Unscrew the conduit plug.
f.
Pull the cabling through the hole.
g.
Apply appropriate sealant around the opening.
Connect the Wiring
Video: female BNC
Power
Red +
Black –
Note
For secure installations, surface mounted cables should be protected by
plastic or metal cable covers.
2
Mount the Camera
Surface Mount Installations Without an Electrical Box
Secure the camera to a wall or ceiling using #6-1 7/16 inch slotted Type A screws
(x4) supplied. For wall mount installations, orient the conduit plug face down to
prevent moisture from entering housing.
4S Electrical Box Installation
Ceiling/wall
Optional: Secure
adapter plate to the
4S electrical box.
Secure the base with
supplied screws.
4
Adjust the Camera
1.
Apply 12 VDC or 24 VAC power to the camera and monitor the video signal.
2.
Loosen the screws that lock the gimbal assembly in place.
3.
Adjust the camera carrier to the desired view, then retighten the screws.
4.
Orient as shown below to maintain the correct picture orientation.
Top view
Loosen locking screw to
Locking
adjust Horizontal (B).
screw
Set focus
Set focal length
(bottom)
(top)
Lenses are pre-focused at the factory. In the unlikely event the optical effect of the
dome causes a slight defocusing of the lens, hold the dome over the lens to make to
make a final adjustment.
Electrical box
(not supplied)
Screws (not supplied)
HD4U base
#6- 1 7/16 Inch
slotted Type A screws
(surface mount
without electrical box)
Angle view
Loosen setscrews
(x2) to adjust Pan (C).
B
C
Legend
A = Tilt rotation
B = Horizontal rotation
A
C = Pan rotation
Advertisement
Related Manuals for Honeywell HD4U
Summary of Contents for Honeywell HD4U
- Page 1 Day/Night Ultra Wide Dynamic Fixed Dome Camera Quick Install Guide Thank you for purchasing a Honeywell Day/Night Ultra Wide Dynamic Fixed Dome Prepare for Installation Mount the Camera Camera. Before installing the camera, please verify your model and read this guide...
- Page 2 +1.800.796.CCTV (North America only) © 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The HVSsupport@honeywell.com information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use Document 800-00032 –...