Related Manuals for Honeywell HD4DX
Summary of Contents for Honeywell HD4DX
-
Page 1: User Guide
Day/Night DNS Fixed Dome Camera NTSC / PAL HD4D HD4DX User Guide Document 800-00023 – Rev D – 05/07... - Page 2 Revisions Issue Date Revisions 04/07 New document. 05/07 Increase line weight of illustrations. 05/07 Corrected specifications. 06/07 Changes: Page 14, LL switch is on power supply board. Page 18, corrected Day/Night mode explanation. Page 24, corrected Vertical Phase Adjustment to 0 - 359°.
-
Page 3: Explanation Of Graphical Symbols
Warnings Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards. -
Page 4: Fcc Compliance Statement
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 5: Table Of Contents
Contents Introduction ..........6 Before You Begin . -
Page 6: Introduction
One bag containing mounting screws • One Product warranty If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service (see Warranty and Service). Equipment Required You will require the following tools to complete the installation: •... -
Page 7: Installation
Installation The HD4D is weather-sealed for indoor or outdoor locations. The HD4D is a fully-integrated enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of tampering. Figure 1 Installation Components HD4D dome enclosure Document 800-00023 Rev D 05/07... -
Page 8: Mounting The Camera
Mounting the Camera The HD4D Camera is designed to be surface mounted on a wall or ceiling. Before you mount the camera, use the mounting template provided to mark and pre-drill the holes. Connecting Cables Through the Housing Base For installations requiring pulling cables through the grommet located in the bottom of the base: Use a sharp knife to cut an ! opening in the base gasket (see the figure below). -
Page 9: Connecting Cables Through The Side Conduit
Connecting Cables Through the Side Conduit Peel back the bottom flat gasket below the side conduit just enough to expose the security screw. Use the Allen key supplied to loosen and remove the security screw (see below). Use a flat screwdriver to unscrew the conduit plug. Pull the cabling through the hole. -
Page 10: Electrical Box Installations
(supplied) For surface mount installations (without an electrical box), use #6-1 7/16 inch slotted Type A screws (x4) supplied Note Honeywell recommends that you orient the conduit plug facing downwards (wall mount installations) to prevent moisture from entering the housing. - Page 11 Figure 3 illustrates how to mount the HD4D directly to a double gang or single gang electrical box. Figure 3 Double Gang/Single Gang Electrical Box Installation (Single Gang Shown) Electrical box (not supplied) Ceiling/wall HD4D base Secure the HD4D base with screws appropriate to your installation (not supplied) For surface mount...
-
Page 12: Connecting The Wiring
Connecting the Wiring Follow Figure 4 for the wiring connection. Figure 4 Wiring Connection Note For secure installations, surface mounted cables should be protected by plastic or metal cable covers. Video: female BNC (yellow) + Red Power: 12 VDC - Black or 24 VAC... -
Page 13: Adjusting The Camera
Adjusting the Camera To adjust the HD4D Camera: Apply 12 VDC or 24 VAC power to the camera and monitor the video signal. Loosen the screws that lock the gimbal assembly in place (see Figure Adjust the camera carrier to the desired view. Tighten the screws to lock the gimbal assembly in place. -
Page 14: Line Lock
Line Lock The Line Lock switch on the power supply board must be left in the ON position. To switch between Line Lock and Internal Lock, use the OSD menu (see Sync Control Setup, page Adjusting the Lens Focus Lenses are pre-focused at the factory but may require a final adjustment after installation in the unlikely event the optical effect of the dome causes a slight defocusing of the lens. -
Page 15: Camera Settings
Camera Settings Camera Functions Figure 6 Camera Controller Legend # Description Video-test monitor output connector Camera OSD control (four position plus center push) Press this control To do this UP, DOWN Select a new item LEFT, RIGHT Select a menu item SETUP (MENU) Enter SETUP MENU, (CENTER PUSH) -
Page 16: Osd Menu Structure
OSD Menu Structure The HD4D camera menu system consists of one main setup menu for easy programming. Main MENU Sub-Menus Options ↵ SETUP MENU LENS VIDEO MANUAL SHUTTER FLK (FLICKERLESS) ↵ ↵ MANUAL ↵ WHITE BAL. MANUAL ↵ BACKLIGHT MIDDLE HIGH ↵... -
Page 17: Setup Menu
SETUP Menu Menu Item Option Description LENS Selects Lens type. Only DC mode is supported at this time. VIDEO Caution MANUAL Selecting VIDEO or MANUAL adversely affects camera operation. SHUTTER Adjusts shutter settings. MANUAL FLK (Flickerless) reduces on-screen flickering. MANUAL adjusts the shutter speed from 1/60-1/120,000 of a second (NTSC) or 1/50-120,000 of a second (PAL). -
Page 18: Special Menu
SPECIAL Menu On the main SETUP menu: Press UP or DOWN and then select SPECIAL. Push SETUP (MENU) to access the SPECIAL menu. Menu Item Option Description CAMERA ID Turns ID display off and on. To add a camera title (name and/or number) to be displayed on the screen, see Adding a Camera Title Display. -
Page 19: Adding A Camera Title Display
Adding a Camera Title Display On the SPECIAL menu, select CAMERA ID, then press SETUP (MENU).. Press the menu control UP, DOWN, LEFT, or RIGHT CAMERA ID to select a character, then press (SETUP) MENU to accept it. The character is saved and the title cursor A B C D E F G H I J K L M N O P R Q S T U V W X Y Z at the bottom of the screen moves to the next... -
Page 20: Motion Detection Setup
Motion Detection Setup On the SPECIAL menu, select MOTION DET, then press SETUP (MENU). Menu Item Option Description MOTION DETECTION AREA SEL AREA 1 Select which of the four motion AREA SEL AREA 1 AREA 2 detection grids top left, top right, AREA STATE |..|....| 10 AREA 3... -
Page 21: Installing The Enclosure Cover
Installing the Enclosure Cover To install the enclosure cover, use the Allen key (supplied) to secure the HD4D dome enclosure to the base with four #8-32 security screws. Figure 7 Enclosure Cover Installation HD4D dome enclosure #8-32 security screws (x4) Routine Maintenance Use regular liquid cleaners to remove dirt and grime from the HD4VC4HR dome. -
Page 22: Solving Common Technical Issues
See Specifications details. Check the video signal connections are correct. Check for a loose connection. Fuzzy Video Check the video ground connections. Check for ground loops. Call Honeywell Technical Support for additional assistance (see Warranty and Service). -
Page 23: Warranty And Service
Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.796.CCTV for assistance or to request a Return Merchandise Authorization (RMA) number. -
Page 24: Specifications
Specifications Video Signal Specifications Pickup device: 1/3 in. Sony Interline CCD sensor Synchronization system: 12 VDC: Internal / 24 VAC: (Internal or Line lock) Vertical phase adjustment: Adjustable, 0° - 359°, OSD control Horizontal resolution: 540 TV lines Lens type: 3.3 - 12 mm Vari-focal Auto Iris, IR Corrected F1.5, DC Drive Minimum illumination response: 0.3 lux @ F1.5 (Color) - Page 25 Format Specifications NTSC Color video signal format: Standard Standard Effective picture elements: 768 (H) x 494 (V) 752 (H) x 582 (V) Scanning system (2:1 interlace): 525 lines, 60 fields/sec. 625 lines, 50 fields/sec. Electronic shutter: 1/60 - 1/120,000 second 1/50 - 1/120,000 second General Specifications Construction: Die cast (housing) Polycarbonate (dome)
-
Page 26: Cable Guidelines
Calculations are based on an unregulated linear power supply, which would be the worst case. Using a regulated or switching power supply can increase the cable distance. Honeywell recommends using a CSA Certified/UL listed Class 2 power adapter to ensure compliance with electrical safety standards. - Page 27 HD4D/HD4DX Mounting Template Document 800-00023 Rev D 05/07...
- Page 28 05/07 © 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.