Honeywell HD4D Quick Install Manual
Day/night dns fixed dome camera
Hide thumbs
Also See for HD4D:
- User manual (28 pages) ,
- Specifications (2 pages) ,
- Specifications (2 pages)
Advertisement
Quick Links
Download this manual
See also:
User Manual
Day/Night DNS Fixed Dome Camera
Quick Install Guide
Thank you for purchasing a Honeywell Day/Night DNS Fixed Dome Camera.
Before installing the camera, please verify your model and read this guide
carefully.
Model
Signal
HD4D
NTSC
HD4DX
PAL
Warnings
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
Warning
12 VDC/24 VAC models require the use of CSA Certified/UL Listed
Class 2 power adapters is required to ensure compliance with
electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct
disposal of this product (applicable in the European Union and other
European countries with separate collection systems). This product
should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
FCC Compliance
Information to the User: This equipment has been tested and found to comply with
the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Caution
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant
with the essential protection requirements of the EMC directive 89/336/EEC and the
Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN
55022 for emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipment
safety.
Unpack Everything
You will also require a Phillips screwdriver and side-cutters.
1
Prepare for Installation
1.
Use the mounting template to mark and pre-drill the holes.
2.
Connect the cables:
Through the grommet in the housing base
Through the side conduit
Document 800-00027 – Rev B – 05/07
Vari-focal Auto Iris Lens
3.3 - 12 mm
3.3 - 12 mm
HD4D/X Camera
+ factory-installed pigtail power and video
connectors
This guide
Mounting template
Hardware Kit
Allen wrenches (x3)
8-32 x 1/8" screws (x4)
#6 - 1 7/16" slotted Type A screws (x4)
a.
Use a sharp knife to cut an opening in
the base gasket ! only large enough to
feed the cable assembly through.
b.
Apply sealant around the opening.
c.
Peel back the bottom flat gasket below
the side conduit to expose the security
screw.
d.
Use the Allen key to remove the security
screw.
e.
Unscrew the conduit plug.
f.
Pull the cabling through the hole.
g.
Apply appropriate sealant around the
opening.
2
Mount the Camera
Surface Mount Installations Without an Electrical Box
Secure the camera to a wall or ceiling using #6-1 7/16 inch slotted Type A
screws (x4) supplied.
4S Electrical Box Installation
Ceiling/wall
Optional: Secure
adapter plate to the
4S electrical box.
Secure the base
with supplied
screws.
Note
For wall mount installations, orient the conduit plug face down
to prevent moisture from entering housing.
Double Gang/Single Gang Electrical Box Installation
Ceiling/wall
Secure the base with
screws appropriate
to your installation
(not supplied)
3
Connect the Wiring
Video: female BNC
(yellow)
Power: 12 VDC
or 24 VAC
4
Adjust the Camera
Orient as shown below to maintain the correct picture orientation.
Top view
Loosen locking screw to
adjust Horizontal (B).
Set focal length
Leave Line
Lock ON*
(bottom)
*To switch between Line Lock and Internal, use OSD menus (see
"SYNC" in the "SETUP Menu").
Electrical box
(not supplied)
Screws (not supplied)
HD4D base
#6- 1 7/16 Inch
slotted Type A screws
(surface mount
without electrical box)
Electrical box
(not supplied)
HD4D base
#6- 1 7/16 Inch slotted Type A
screws (surface mount without
electrical box)
Note
For secure
installations, protect
surface mounted
cables with plastic or
+ Red
metal cable covers.
- Black
Connect service
Apply power (12 VDC
monitor cable to the
or 24 VAC) to the
video monitor output.
camera.
Angle view
Loosen setscrews
Locking screw
(x2) to adjust Pan (C)
B
C
Legend
A = Tilt rotation
Set focus
B = Horizontal rotation
A
(top)
C = Pan rotation
Advertisement
Related Manuals for Honeywell HD4D
Summary of Contents for Honeywell HD4D
-
Page 1: Mount The Camera
Day/Night DNS Fixed Dome Camera Quick Install Guide Mount the Camera Thank you for purchasing a Honeywell Day/Night DNS Fixed Dome Camera. Before installing the camera, please verify your model and read this guide carefully. Surface Mount Installations Without an Electrical Box... - Page 2 +1.800.796.CCTV (North America only) © 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written HVSsupport@honeywell.com permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.