hit counter script
Whirlpool Washer User Instructions
  1. Manuals
  2. Brands
  3. Whirlpool Manuals
  4. Washer
  5. WASHER
  6. User instructions
Whirlpool Washer User Instructions

Whirlpool Washer User Instructions

Hide thumbs Also See for Washer:
Table of Contents

Advertisement

Quick Links

See also: Programme Chart , Instructions for Using
This information covers several different models. Your washer may vary from the model shown and may not have all the cycles and
features described. Washer will not agitate or spin with the lid open.
CYCLES
LOAD TYPES
COTTONS
Cottons and linens, loads that are
moderately or heavily soiled.
HEAVY DUTY
Heavily soiled loads.
EVERYDAY
Permanent press blends and
WEAR
synthetic fabrics that are lightly to
moderately soiled.
WOOLENS
Lightly to moderately soiled
washable woolens and washable
knits.
DELICATES
Lightly to moderately soiled delicate
items and washable knits.

Temperature Control

You should select a Wash/Rinse temperature based on the type of
fabric and soils being washed. For best results, use the warmest
wash water safe for fabric. Follow garment label instructions.
Your washer uses automatic temperature control to maintain a
uniform water temperature by regulating incoming hot and cold
water. This helps eliminate undissolved detergent and ensures
consistent cleaning results. The cold wash is regulated at
approximately 24°C by adding small amounts of hot water during
the cold fill. The warm wash is maintained at approximately 38°C.
8558483
© 2003 Whirlpool Corporation.
All rights reserved.
WASHER CYCLE DESCRIPTIONS
Cycle Selections
DESCRIPTIONS
A wash time should be selected
based on the soil level of your load.
You may choose Heavy Duty,
Normal or Light.
Review detergent use instructions.
You should use twice the amount of
detergent recommended for a
normal wash cycle.
Features a cool down, rinse and
low-speed final spin to reduce
wrinkling.
Features a series of brief agitations
and soaks, followed by a short spin.
Features a series of brief agitations
and soaks, followed by a short spin.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
®
Load Size or Water Level Control
Adjust water level to load size. Clothes should move freely. To
change to a higher water level after agitation starts, you may turn
knob to desired setting.
On models with a variable Load Size or Water Level control, you
should turn the knob to RESET, then to desired setting.
AGITATE/
APPROXIMATE
SPIN SPEEDS
WASH TIMES
High/High
6 - 15 minutes
High/High
15 minutes
High/Low
6 - 10 minutes
Intermittent
6 minutes
Low/Low
Intermittent
4 minutes
Low/Low
Printed in U.S.A.
12/03

Advertisement

Table of Contents
loading

Related Manuals for Whirlpool Washer

Summary of Contents for Whirlpool Washer

  • Page 1: Temperature Control

    ® WASHER CYCLE DESCRIPTIONS This information covers several different models. Your washer may vary from the model shown and may not have all the cycles and features described. Washer will not agitate or spin with the lid open. Cycle Selections...

  • Page 2: Table Of Contents

    Purchase date __________________________________________________ NOTE: If the power supply cord of this washer is damaged, it must be replaced by a special cord (Part Number 8541726) available from the dealer from whom you purchased the washer or a Whirlpool designated service company.

  • Page 3: Washer Safety

    IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: Read all instructions before using the washer.

  • Page 4: Washer Use

    (including cooking oils). Doing so can result in death, explosion, or fire. 1. Measure detergent and pour it into the washer. If desired, add Style 1: With liquid chlorine bleach dispenser (on some powdered or liquid color safe bleach. Drop a sorted load of models) clothes loosely into your washer.

  • Page 5: Washer Care

    Storage, non-use or vacation care Water Inlet Hoses Operate your washer only when you are at home. If you will be on Replace inlet hoses after 5 years of use to reduce the risk of hose vacation or not using your washer for an extended period of time, failure.

  • Page 6: Troubleshooting

    Instructions. Is the washer in a normal pause in the cycle? The washer Is the sink or drain clogged? Sink and standpipe must be pauses for about 2 minutes during certain cycles. Allow the able to handle 64 L of water per minute.

  • Page 7: Washer Results

    Wash/Rinse temperature not what I selected Load is wrinkled Are the hot and cold water inlet hoses reversed? See the Did you unload the washer promptly? Unload the washer as Installation Instructions for more information. As your soon as it stops.
  • Page 8 Notes...

  • Page 9: Warranty

    Whirlpool (Australia) Pty Limited will not pay for: 1. Service calls to correct the installation of your washer, to instruct you how to use your washer, or to replace house fuses or correct house wiring or plumbing.
  • Page 10 Parts supplied: Tools and Parts Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer basket. Tools needed for connecting the drain hose and water inlet hoses: Pliers that open to 3.95 cm...
  • Page 11 Your washer can be installed in a basement, laundry room, closet, or recessed area. (See “Drain System.”) Ruler or measuring tape IMPORTANT: Do not install or store the washer where it will be Parts supplied: exposed to the weather. Proper installation is your responsibility.

  • Page 12: Tools And Parts

    Time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided. This washer is equipped with a power supply cord having an earthing plug. To minimize possible shock hazard, the cord must be plugged...

  • Page 13: Installation Instructions

    2. Pull firmly to remove the end of the shipping strap that remains pinned to the back of the washer. This will release the rear self-leveling feet. 5. Place clamp over area marked “CLAMP.” Release clamp.

  • Page 14: Connect The Inlet Hoses

    8. Turn on the water faucets and check for leaks. A small amount 2. Attach a hose to the hot water faucet. Screw on coupling by of water might enter the washer. You will drain this later. hand until seated on the washer.

  • Page 15: Washer Use

    Step 3 of “Remove Shipping Strap.” Remaining portion of shipping strap 9. After the washer is in the final location and level, use a 14 mm open-end wrench to turn the nuts on the feet tightly against 4.

Table of Contents