Page 2
Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly. Along with a wide range of accessories...
Contents CONTENTS 4 Safety information 6 Installation 12 Product description 12 Operation 14 Helpful hints and tips 15 Care and cleaning 16 What to do if… 18 Technical data 19 Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to...
Safety information SAFETY INFORMATION WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it.
Page 5
Safety information • Pots must not enter the control zone. • Do not use not stable cookware to prevent from tilt and accident. • Do not put flammable products or items that are wet with flammable products, and/or fusible objects (made of plastic or aluminium) and/or fabrics in, near or on the appliance. There is the risk of explosion or fire.
Installation • This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention must be given to the relevant requirements regarding ventilation. • The use of a gas cooking appliance cause heat and moisture in the room in which it is installed.
Installation Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regula- tions (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Instal- lation I.S.
Installation End of shaft with nut Washer Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or cop- per. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation.
Installation Adjustment of minimum level To adjust the minimum level of the burners: 1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the control knob. 4. With a thin screwdriver, adjust the bypass screw position. If you change from natural gas 20 mbar to liquid gas, fully tighten the adjustment screw in.
Page 10
Installation Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rating plate is located on the bottom of the hob. The hob is supplied with a 3 core flexible supply cord incorporating a 3 amp plug fitted. In the event of having to change the fuse, a 3 amp ASTA approved (BS 1362) fuse must be used.
Installation Replacement of the connection cable To replace the connection cable use only H05V2V2-F T90 or equivalent type. Make sure that the cable section is applicable to the voltage and the working temperature. The yellow/ green earth wire must be approximately 2 cm longer than the brown (or black) phase wire. Building In min.
Product description 50 cm 2 120 cm 2 180 cm 2 360 cm 2 MANUFACTURER: ELECTROLUX ITALIA S.p.A. C.so Lino Zanussi, 30 33080 PORCIA (PN) - ITALIA PRODUCT DESCRIPTION Cooking surface layout Triple Crown burner Semi-rapid burner Semi-rapid burner Semi-rapid burner Auxiliary burner Control knobs Control knobs...
Page 13
Operation To light the burner: 1. Turn the control knob counterclockwise to the maximum position ( ) and push it down. 2. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up. If not, the gas supply will be interrupted. 3.
Helpful hints and tips Burner cap Burner crown Ignition candle Thermocouple WARNING! Do not keep the control knob pushed for more than 15 seconds. If the burner does not light after 15 seconds, release the control knob, turn it into off posi- tion and try to light the burner again after minimum 1 minute.
Care and cleaning WARNING! Use pots and pans with diameter applicable to the dimension of burner. Do not use cooking vessels on the hotplate that overlap its edges. Burner Diameters of cookware Triple Crown 180 - 260 mm Semi-rapid (rear left) 120 - 240 mm Semi-rapid (rear right) 120 - 240 mm...
What to do if… • You can remove the pan supports to easily clean the hob. • To clean the enamelled parts, cap and crown, wash it with warm soapy water and dry it carefully before you put them back. •...
Page 17
What to do if… Problem Possible cause Remedy • Burner cap and crown are • Make sure that the burner placed uneven cap and crown are in correct positions. The flame is blow out immedi- • Thermocouple is not heated •...
Environment concerns NORMAL POWER NORMAL REDUCED NATURAL GAS LPG (Butane/Propane) POWER POWER G20 (2H) 20 mbar G30/G31 (3+) 28-30/37 mbar BURNER 28-30 inj. 1/100 inj. 1/100 37 mbar m³/h mbar Semi-rap- 0.45 0.181 id burner Triple 0.362 Crown burner ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste.