Advertisement
Quick Links
30" Slide-in Range
INSTALLATION ANDSERVICE MUSTDEPERFORMED B YA QUALiFiED I NSTALLER,
iMPORTANT: SAVE THiS INSTALLATION MANUAL FOR LOCAL ELECTRICAL
iNSPECTOR'S USE,
READANDSAVETHESEINSTRUCTIONS FORFUTUREREFERENCE,
For SAFETY CONSiDERATiONS
do not instaJJa appJiance in any combustibJe
cabinetry
which is not
in accord with the stated clearances
and dimensions
on page 2. See Figures 1 and 2.
RANGE MEASUREMENTS . .....................................
2
CLEARANCES ANDDiMENSiONS ..............................
2
iMPORTANT NOTES .............................................
3
UNPACKING ANDEXAMiNiNG YOURRANGE .................
3
iMPORTANT SAFETYiNSTRUCTiONS .........................
3
ELECTRICAL
CONNECTIONS
................................
4=6
MODELANDSERIAL NUMBER LOCATION ....................
4
ANTI-TIP .....................................................
6-8
CANE,CLEANING ANDMAINTENANCE......................
8
¸¸¸¸¸¸;¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸2¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸.¸¸¸¸¸¸¸¸¸¸¸¸¸¸
....
®
Insight
'_
Advertisement
Related Manuals for Sharp KB-4425LW
Summary of Contents for Sharp KB-4425LW
- Page 1 30" Slide-in Range INSTALLATION ANDSERVICE MUSTDEPERFORMED B YA QUALiFiED I NSTALLER, iMPORTANT: SAVE THiS INSTALLATION MANUAL FOR LOCAL ELECTRICAL iNSPECTOR'S USE, READANDSAVETHESEINSTRUCTIONS FORFUTUREREFERENCE, For SAFETY CONSiDERATiONS do not instaJJa appJiance in any combustibJe cabinetry which is not in accord with the stated clearances and dimensions on page 2.
-
Page 2: Installation
iNSTALLATiON MANUAL 31 1/4" If using countertop with integrated glass end drip edge, remove 5/8" to make control panel 5/8" min. flush as illustrated. 29 7/8" minimum 30" to bottom of cabinet over 18" to upper 36" cabinets to bottom of cooktop surfece 36 _'... - Page 3 If there is any damage, do not operate on the range to reach items. the Microwave Drawer and contact your dealer or a SHARP ° To eliminate the need to reach over the cooktop, cabinet storage AUTHORIZED SERVICER.
- Page 4 iNSTALLATiON MANUAL 2081240 VOLT CONNECTION iNSTRUCTIONS The range can be set for 208V or 240V. The voltage setting for your The installer or consumer is responsible for connecting the power range is pre-set at 240V from the factory. Follow these steps to supply cord to the connection block located behind the back panel change the voltage setting.
- Page 5 iNSTALLATiON MANUAL center, lowest screw. See Figure 10. The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap. 4-W|RE CONNECTION iNSTRUCTiONS If the ground strap is removed for any reason, Before wiring the range, review the suggested power source location separate ground wire must be connected to the separate ground drawing in Figure 2.
-
Page 6: Normal Installation
INSTALLATION MANUAL _ln°C k'"_ line2 terminal _round plate ground screw Figure t t Figure NORMAL INSTALLATION STEPS ANTI-TIP BRACKET INSTALLATION iNSTRUCTiONS LOCATE THE BRACKET - USING THE TEMPLATE IMPORTANT SAFETY WARNING The bracket may be located on either the left or right side of the To reduce the risk of tipping of the range,... - Page 7 |NSTALLAT|ON MANUAL • Adjust the back leveling legs with an adjustable wrench or pliers. Measure from the floor to the bottom of the cooktop glass (X) and adjust the legs to match the measurement (Y) taken from max 11/4" leveling leg the cutout.
- Page 8 Refer to your Operation Manual for our service address. Sharp's toll-free telephone number is 1-800-BE-SHARP (1-800-237-4277). Please call or write if you have inquiries about your range product and/or need to order parts. Please do not open or close the lower oven door for 30...