Table of Contents
Advertisement
Quick Links
sPECIal WaRnInG
InstallatIon anD sERVICE Must BE PERFoRMED BY a QualIFIED InstallER.
IMPoRtant: saVE thIs InstallatIon Manual FoR loCal ElECtRICal
InsPECtoR's usE.
REaD anD saVE thEsE InstRuCtIons FoR FutuRE REFEREnCE.
ClEaRanCEs & DIMEnsIons
For SAFETY CONSIDERATIONS do not install a appliance in any combustible cabinetry which is not
in accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.
RanGE MEasuREMEnts ......................................2
ClEaRanCEs anD DIMEnsIons ..............................2
IMPoRtant notEs .............................................3
unPaCkInG anD ExaMInInG YouR RanGE .................3
IMPoRtant saFEtY InstRuCtIons .........................3
30" Slide-in Range
InstallatIon Manual
ElECtRICal ConnECtIons ................................ 4-6
MoDEl anD sERIal nuMBER loCatIon ....................4
antI-tIP ..................................................... 6-8
CaRE, ClEanInG anD MaIntEnanCE ......................8
Advertisement
Table of Contents
Related Manuals for Sharp Insight Electric Rang
Summary of Contents for Sharp Insight Electric Rang
-
Page 1: Table Of Contents
2. See Figures 1 and 2. RanGE MEasuREMEnts ...2 ClEaRanCEs anD DIMEnsIons ...2 IMPoRtant notEs ...3 unPaCkInG anD ExaMInInG YouR RanGE ...3 IMPoRtant saFEtY InstRuCtIons ...3 30" Slide-in Range ElECtRICal ConnECtIons ... 4-6 MoDEl anD sERIal nuMBER loCatIon ...4... -
Page 2: Range Measurements
• Contact surface must be solid and level. Pay special attention to the floor. Be sure it is solid enough for the weight of the range. Check that the floor covering is smooth and flat and that it adheres to the sub-floor solidly. • Check location where the range will be installed for proper electrical supply. -
Page 3: Important Notes
Microwave Drawer and contact your dealer or a SHARP AUTHORIZED SERVICER. IMPoRtant saFEtY InstRuCtIons If the information in this manual is not followed exactly, a fire or electrical shock may result causing property damage, personal injury or death. -
Page 4: Electrical Connections
Model and serIal nuMber loCatIon The rating plate, including model and serial number, is located on the faceplate behind the Microwave Drawer front. 208/240 Volt ConneCtIon InstruCtIons The range can be set for 208V or 240V. The voltage setting for your range is pre-set at 240V from the factory. Follow these steps to change the voltage setting. Locate the voltage switch on the lower back side of the range. Remove the screw and rotate the switch plate 180˚ as indicated in the Figure 4. - Page 5 A ground strap is installed on this range which connects the center terminal of the neutral terminal block to the range chassis. The ground strap is connected to the range by the 4-WIre ConneCtIon Connect line 1 here. Cut ground strap.
-
Page 6: Anti-Tip
Figure 13b Mark the floor or wall where left or right side of the range will be located. If rear of range is against the wall or no further than 1 1 /4-inches from wall when installed, you may use the wall or floor mount method. See Figure 14. If molding is installed and does not... - Page 7 The Figure 18 note: the bottom of the range and the leveling leg to allow room for the bracket. Use a level to check your adjustments. Plug range into properly prepared electrical receptacle or if hard wired, check that it was completed properly. Check floor condition for evenness and stability. Slide range back into position. See Figure 19. 1 5 /8" to edge of bracket Range Slide...
-
Page 8: Care, Cleaning And Maintenance
InstallatIon Manual Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip bracket by looking underneath the range with a flashlight and carefully attempt to tilt it forward. Slide range into cabinet until control panel edge is flush with the countertop front edge. Figure 20 T IN S EB 4 5 5MRR1 CaRE, ClEanInG anD MaIntEnanCE Refer to the Operation Manual for cleaning instructions. If removing...