hit counter script
Sharp QT-CD131H Operation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Stereo System
  5. QT-CD131H
  6. Operation manual
Sharp QT-CD131H Operation Manual

Sharp QT-CD131H Operation Manual

Portable cd stereo system
Hide thumbs Also See for QT-CD131H:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
YT
<P=001>
PORTABLE CD STEREO SYSTEM
Thank you for purchasing this SHARP product.
For the best performance, read this manual care-
fully. It will guide you in operating your SHARP
product.
The mains lead of this product is fitted with a non-rewire-
able (moulded) plug incorporating a 3A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS
1362 fuse marked
or
and of the same rating as
above, which is also indicated on the pin face of the plug
must be used.
Always refit the fuse cover after replacing the fuse. Never
use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home
not being compatible with the plug supplied, cut-off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and
the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be in-
serted elsewhere into a 13A socket outlet as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the
instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this
product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to
the plug terminal which is marked N or coloured black.
The wire which is coloured brown must be connected
to the plug terminal which is marked L or coloured red.
MODEL
QT-CD131H
OPERATION MANUAL
NOTE FOR USERS IN THE U.K.
Ensure that neither the brown nor the blue wire is con-
nected to the earth terminal in your three pin plug.
Before replacing the plug cover, make sure that:
If the new fitted plug contains a fuse, its value is the
same as that removed from the cut-off plug.
The cord grip is clamped over the sheath of the mains
lead and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED
ELECTRICIAN.
SERVICE INFORMATION
In the unlikely event of your equipment requiring repair,
please contact the dealer or supplier from whom it was
purchased. Where this is not possible, please contact
the telephone number listed below. You will then be
given details of how to obtain service.
Please note; all calls will be charged at local rate.
Certain replacement parts and accessories may be ob-
tained from our main parts distributor.
MANCHESTER 0161-682-1415
READING
In the unlikely event of this equipment requiring repair
during the guarantee period, you will need to provide
proof of the date of purchase to the repairing company.
Please keep your invoice or receipt, which is supplied at
the time of purchase.
QT-CD131H(SUK) TINSE0007SJZZ
- 0345-125387 -
WILLOW VALE ELECTRONICS LTD.
01189-876444

Advertisement

Table of Contents
loading

Related Manuals for Sharp QT-CD131H

Summary of Contents for Sharp QT-CD131H

  • Page 1 OPERATION MANUAL Thank you for purchasing this SHARP product. For the best performance, read this manual care- fully. It will guide you in operating your SHARP product. NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewire- Ensure that neither the brown nor the blue wire is con- able (moulded) plug incorporating a 3A fuse.

  • Page 2: Special Notes

    Caution: Recording and playback of any material may require consent, which SHARP is unable to give. Use of controls, adjustments or performance of Please refer particularly to the provisions of the procedures other than those specified herein Copyright Act 1956, the Dramatic and Musical may result in hazardous radiation exposure.
  • Page 3 Do not write on either side of the disc, particularly damage. SHARP will not be held responsible for any the non-label side. Signals are read from the damage resulting from use of this unit with a voltage non-label side.

  • Page 4: Battery Power

    <P=003> Battery power AC power AC 230 - 240 V, 50 Hz To AC INPUT 2 "AA" size batteries 8 "D" size batteries (UM/SUM-3, R6, HP-7 (UM/SUM-1, R20, HP-2 or similar) for Tuner or similar) memory When inserting or removing the batteries ë...
  • Page 5 <P=001> CD playback Set the FUNCTION Load a CD. Press the switch to CD. PLAY/REPEAT button. CD EJECT PLAY / REPEAT FUNCTION TAPE TUNER Open Label facing up " " will appe ar STAND-BY and playback will Close begin from track 1. "Cd"...

  • Page 6: Radio Operation

    <P=002> Radio operation Manual tuning Set the Select the desired fre- Press the TUNING ( ) but- FUNCTION quency band. (FM ST, ton to tune into the desired sta- switch to TUNER. FM or AM) tion. FM STERO TUNING DOWN FUNCTION TAPE TUNER...
  • Page 7 <P=003> Radio operation (Continued) To recall a memorised station Set the Select the desired fre- Press the PRESET ( ) but- FUNCTION quency band. (FM ST, ton to recall the desired preset switch to TUNER. FM or AM) channel number. FM STERO PRESET FUNCTION...

  • Page 8: Tape Playback

    <P=001> Tape playback Set the FUNCTION Load the cassette into the cassette Press the PLAY switch to TAPE. compartment. button. FUNCTION PLAY STOP/EJECT TUNER TAPE STAND-BY PAUSE STOP/EJECT To interrupt To stop playback playback PAUSE REWIND When stopped, To resume To rewind the tape playback Precautions:...
  • Page 9 <P=002> Recording from the CD Set the FUNCTION P ress the Load a blank cassette Press the switch to CD. into the cassette RECORD PLAY/REPEAT button. compartment. button on the FUNCTION PLAY / TUNER TAPE STOP/EJECT REPEAT RECORD STAND-BY Load the disc to be recorded.

  • Page 10: Specifications

    AM; 522 - 1,620 kHz TERMS OF GUARANTEE Sharp Electronics (UK) Ltd. ("Sharp") guarantees to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below:- This guarantee shall only apply to faults which are due to inferior workmanship or materials.

Table of Contents