Brother BP2100 Operation Manual page 173
Embroidery machine
Hide thumbs
Also See for BP2100:
- Quick setup manual (32 pages) ,
- Manual de instrucciones (180 pages) ,
- Operation manual (180 pages)
Table of Contents
Advertisement
Marks
Not enough available memory to save the pattern. Delete
another pattern?
OK to automatically lower the presser foot?
OK to delete the selected pattern?
OK to recall and resume previous memory?
OK to reset the pattern's border setting, position and/or angle? This message appears when you try to use the automatic
OK to revert to the original position and/or angle?
Preventive maintenance is recommended.
Retrieving the pattern. Wait a moment.
Sensor module error.
Set the clock.
The bobbin thread is almost empty.
The bobbin winder safety device has activated. Is the thread
tangled?
The carriage of the embroidery unit will move. Keep your
hands etc. away from the carriage.
The needle will move. Keep your hands etc. away from the
needle area.
The pattern extends out of the pattern area, repeat positioning
of center and angle using sensor pen.
The pockets are full. Delete a pattern.
The safety device has been activated.Is the thread tangled? Is
the needle bent?
The shutoff support mode has been activated. Turn off the
machine.
The upper thread may not be threaded correctly. Thread the
upper thread from the beginning.
The USB media was changed. Do not change the USB media
while it is being read.
There is no needle plate cover. Attach a needle plate cover.
This file cannot be used.
Error Messages
Cause/Solution
This message is displayed when the memory is full and the
pattern cannot be saved.
This message is displayed when
presser foot is raised).
This message is displayed when the selected pattern is about
to be deleted.
This message appears if the machine is turned off while
sewing, then turned on again.
Press
to return the machine to the condition (pattern
position and number of stitches) when it was turned off. Follow
the procedure described in "If the Thread Breaks During
Sewing" on page E-27 to align the needle position and sew the
remainder of the pattern.
positioning function using the sensor pen with the pattern,
rotated or replaced, or with the border pattern. (see page B-58)
This message appears when you try to use the automatic
positioning function using the sensor pen with the pattern,
rotated or replaced. (see page B-58)
This message is displayed when the machine needs to be
maintained. (see page A-15)
This message is displayed when the machine is retrieving a
previously saved pattern while in "Embroidery Edit" mode.
This message appears when something is wrong with the
sensor unit of the machine. Consult your authorized dealer.
This message appears when the time/date is not set. Set
time/date. (see page B-18)
This message is displayed when the bobbin thread is running
out.
This message is displayed when the bobbin is being wound,
and the motor locks because the thread is tangled, etc.
This message appears before embroidery unit moves.
This message appears when you touch the point closer than 2
cm from the needle drop point with the sensor pen in the
sensor function. (see page B-55)
This message appears when the specified pattern position
extends out of the pattern area. Specify more centered
position of the embroidery frame. (see page B-58)
This message is displayed when the memory is full and a
pattern must be deleted.
This message is displayed when the motor locks due to
tangled thread or for other reasons related to thread delivery.
This message appears when the machine is in the shutoff
support mode. Turn off the machine once to start the machine
again. (see page B-25)
This message is displayed when it seems that the upper
thread has not been threaded correctly.
This message is displayed when you attempt to select a
pattern after the USB media in which the pattern is saved has
been changed.
This message is displayed when the needle plate cover is not
attached.
This message appears if the file format is incompatible with
this machine. Check the list of compatible file formats. (see
page E-44)
ERROR MESSAGES
A
2
is pressed (the
Appendix A-23
- Quick Links:
- Embroidery Machine
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
