Upgrade Process With Service Impact For Nonredundant Platforms; Configuring Sso On A Cisco Asr 1001, Cisco Asr 1002, Or Cisco Asr 1004 Router; Using Subpackages For Software Upgrade On A Cisco Asr 1001 Router - Cisco ASR1002 - ASR 1002 Router Software Configuration Manual
Asr 1000 series aggregation services routers
Hide thumbs
Also See for ASR1002 - ASR 1002 Router:
- Quick start manual (47 pages) ,
- Installation manual (46 pages) ,
- Configuration manual (34 pages)
Table of Contents
Advertisement
Upgrade Process With Service Impact for Nonredundant Platforms
Router# request platform software package install rp 0 file
bootflash:asr1000rp1-sip*02.02.01.122-33.XNB1*.pkg slot 2 force
Install the ESPBASE package on the ESP:
Step 8
Router# request platform software package install rp 0 file
bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*.pkg
Copy the RPBase subpackage into the directory, then upgrade all of the RP subpackages simultaneously.
Step 9
This step will upgrade the RPBase subpackage, which is the last remaining subpackage that requires an
upgrade:
request platform software package install rp 1 file
bootflash:asr1000rp*02.02.01.122-33.XNB1*.pkg force
Enter show version provisioned to confirm that all of the software has been updated.
Step 10
Reload the router using the reload command when appropriate to complete the installation.
Step 11
Downgrades in versions that do not support the {
RPBASE package for the downgrade version will always be present if an upgrade was
previously performed. Removing and restaging all packages will work in this case, but they
effectively put the system into a state where if the RP reloads prior to the installation
being completed, the RP may no longer be bootable.
Upgrade Process With Service Impact for Nonredundant
Platforms
Subpackage software upgrade is supported for nonredundant platforms such as Cisco ASR 1001 Router,
Cisco ASR 1002, and ASR 1004 Routers in subpackage mode. This is because the software upgrade
procedure on these chassis types requires an RP reload when upgrading the RPBase subpackage at the
last step.
During the software upgrade process, there will be outage on the control plane as the entire platform is
rebooted so that access to the router operating system and ROMmon is lost for a period of time.
For non-hardware-redundant chassis types, SIP impact can be mitigated by installing SIPs one slot at a
time if SPAs are redundant across SIPs (such as when using Gigabit Etherchannel). ESP redundancy
provides similar capability for the ESP allowing hitless upgrade of a chassis from one software release
to another. Consolidated package mode does not provide such a per-slot staging option and always incurs
a traffic loss equivalent to simultaneous OIR of all SIPs.
The Cisco ASR 1002 and ASR 1002-F Routers come by default with 4-GB DRAM. The Cisco ASR 1001
Note
Router comes by default with 4-GB DRAM, and is upgradeable up to 8-GB or 16-GB DRAM.
This section explains how to upgrade subpackages on a Cisco ASR 1001, 1002 or 1004 Router. It
contains the following sections:
•
•
•
•
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
76
Configuring SSO on a Cisco ASR 1001, Cisco ASR 1002, or Cisco ASR 1004 Router, page 77
Using SubPackages for Software Upgrade on a Cisco ASR 1001 Router, page 79
Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router
(software upgrade Command Set), page 94
Using SubPackages for Software Upgrade on a Cisco ASR 1002 or Cisco ASR 1004 Router (request
platform Command Set), page 119
Software Upgrade Process
pattern
} syntax are problematic because an
Advertisement
Table of Contents
Troubleshooting
