HP Z600 - Workstation - 6 GB RAM Installation Manual
Hp z series workstations - hp optical bay hard drive bracket installation
Hide thumbs
Also See for Z600 - Workstation - 6 GB RAM:
- User manual (72 pages) ,
- Installation manual (12 pages) ,
- Installation (2 pages)
Table of Contents
Advertisement
Quick Links
HP Optical Bay Hard Drive Bracket
Introduction
This document describes how to install 8.89 cm (3.5 inch) hard drives in the HP optical bay hard drive
bracket and install the bracket in the optical drive bay of an HP
be used for small form factor (SFF) drives pre-mounted in a 3.5-inch adapter.
Kit contents
●
HP optical bay hard drive bracket
●
Four M3 guide screws
●
Warranty information
System requirements
●
Available optical bay position
●
One unused port connector for each hard drive being installed
Before you begin
To view QuickSpecs and determine the compatibility of this product with your HP workstation, see
http://www.hp.com/go/productbulletin.
ENWW
© 2009 Hewlett-Packard Development Company, L.P. Printed in the U.S.
Workstation. This bracket may also
Introduction
1
Advertisement
Table of Contents
Related Manuals for HP Z600 - Workstation - 6 GB RAM
Summary of Contents for HP Z600 - Workstation - 6 GB RAM
-
Page 1: Kit Contents
One unused port connector for each hard drive being installed Before you begin To view QuickSpecs and determine the compatibility of this product with your HP workstation, see http://www.hp.com/go/productbulletin. © 2009 Hewlett-Packard Development Company, L.P. Printed in the U.S. ENWW Introduction... -
Page 2: Warnings And Cautions
Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area marked with this symbol. WARNING! To reduce the risk of electric shock or damage to your equipment: —... -
Page 3: Step 1-Preparing For Component Installation
Step 1—Preparing for component installation NOTE: Workstation models vary. All illustrations are examples only. Accessing the internal components of the workstation If you need help preparing the workstation for this installation, consult the removal and replacement procedures in the service guide for your workstation at http://www.hp.com/support/ workstation_manuals. -
Page 4: Step 2-Installing The Hard Disk Drive
Step 2—Installing the hard disk drive When connecting a SAS hard drive, verify a SAS-to-SATA interconnect cable adapter (supplied with the HP workstation SAS hard drive kit) is attached to the data connector on the SAS hard drive. Figure 1 Attaching the SAS-to-SATA adapter For HP 400 Workstation series only, install 4 black M3 guide screws suppled in the kit in the 4... - Page 5 Lower the drive into the rails Align the four pins on the rails with the holes in the hard drive, and then snap the rails into place Figure 3 Installing the drive in the rails To install the hard drive in the drive bracket, gently squeeze the green tabs while sliding the drive with rails into the bracket Figure 4...
- Page 6 Slide the drive and bracket into the bay. Release the latch just before the bracket is fully- seated, allowing the latch pins to engage. Figure 5 Installing the bracket in the optical bay HP Optical Bay Hard Drive Bracket ENWW...
-
Page 7: Step 3-Configuring The Cabling
Step 3—Configuring the cabling In HP 600 and HP 800 Workstations, if the internal bays are not filled to capacity, the pre-installed blind-mate data cables for the unused internal hard drive bays must be unplugged from the system board, to enable the proper connection of the hard drives installed in this bracket. After all internal and optical bay hard drives are connected, the blind mate cabling may be reconnected to the next available ports on the system board. -
Page 8: Step 4-Reassembling The Workstation
Step 4—Reassembling the workstation Reinstall the front bezel, if applicable. Reinstall the card support, if applicable. Reinstall the airflow guide, if applicable. Reinstall the side access panel. Reconnect power to the workstation and all external devices. Restore power to the workstation and all external devices. Step 5—Setting up the operating system When powering up the workstation after installation, a new hard drive identifies itself as un-initialized storage.