Page 1 Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used SHARP CORPORATION for after sales service only. The contents are subject to change without notice.
Page 2 DM-1505 CAUTION This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH stand- ard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in haz- ardous radiation exposure.
Page 3 DM-1505 At the production line, the output power Caution of the scanner unit is adjusted to 0.57 This product contains a low power laser MILLI-WATT PLUS 20 PCTS and is device. To ensure continued safety do not maintained constant by the operation of remove any cover or attempt to gain access the Automatic Power Control (APC).
Page 4: Major Functions
DM-1505 [1] GENERAL 1. Major functions Item SB/MB 2 Tray R-SPF without SOPM Duplex with USB with USB Model DM-1500 15CPM DM-1505 15CPM Descriptions of items CPM: Copy speed (Copies Per Minute) SB/MB: SB = Manual feed single bypass, MB = Manual feed multi bypass 2 tray: Second cassette unit.
Page 5 DM-1505 [2] SPECIFICATIONS 1. Basic specifications of copier A. Basic specifications Item Spec. Type Desktop Copy system Dry, electrostatic Segment (class) Digital personal copier External dimensions (W × D × H) (mm) DM-1500/DM-1505: 518mm × 482.6mm × 464mm DM-1500: Approx. 25Kg, (drum cartridges included) Weight DM-1505: Approx.
Page 6 DM-1505 Section Item Details Spec. Exit way Face down Paper exit section Capacity of output 100 sheets tray Original set Center Registration (left edge) B4 (10″ × 14″) Max. original size Originals Original kinds sheet Original size None detection Scanning system CCD sensor scanning by lighting lamp scanner CCD sensor Resolution...
Page 7 DM-1505 Section Item Details Spec. 9.6 sec. or below (A4) (Pre-heat mode: 16 sec. or Tray paper feed below / Auto power-shut-off mode: 23 sec. or above) Copy speed First copy time 10.0 sec (Pre-heat mode: 16 sec. or below / Auto Manual paper feed power-shut-off mode: 23 sec.
Page 8 DM-1505 Item Contents Standard Maximum Memory 72MB Expansion Slot for One DIMM slots Memory 64MB, 32MB, 16MB Expansion Memory (commercially-available DIMM:EDO) Switches 1 (Online/Offline) Operation Panel Lamps 2 (DATA, ONLINE) Display None Applicable PC IBM PC-AT Compatibles *: Only Win 98 can be used for USB users. Operations when both of USB/parallel ports are connected at the same time.
Page 9: Supply System Table
DM-1505 [3] CONSUMABLE PARTS 1. Supply system table A. USA, CANADA Name Content Life Product name Package Remark × 1 Developer cartridge Toner/developer cartridge DM-150TD Life setup is based on (Black) (Toner: 220g, Developer: 190g) A4 5% documents. <With IC> For 6% coverage, 5K ×...
Page 10 DM-1505 〈Drum cartridge〉 The label on the drum cartridge shows the date of production. (SOCC production) Production control label attachment position 〈JAPAN production〉 Production control label attachment position(*1) Division ∗1 The production control label is not attached to the cartridge of a Ex production China product.
Page 11 DM-1505 4. Memory Device A. Function The memory device is used to monitor the life of the developer cartridge in the way that the machine reads and writes information (e.g.page count) to the memory device equipped in the developer cartridge. When the life is reached, the memory device becomes nonfunctional to prevent the deterioration of image/text quality and machine damages.
Page 12 DM-1505 2) Remove the DVF cover unit. 5. Consumable parts refill procedure • When removing, be careful not to break the two pins. [External view check points] Check for breakage of the four pins (*) and the ATC sensor connector of the DV BOX unit.
Page 13 DM-1505 5) Tilt the DV box unit and rotate the DV18T clockwise to remove 11) Face the toner supply port of the TH box unit upward, and press developer. and insert the refill hose into the toner supply port with the toner bottle kept straight up.
Page 14 DM-1505 14) Clean the DV box unit with alcohol and attach the DV blade. 20) Install the MG cover. • After drying the unit, attach the DV blade. Put the unit straight with the MG roller on the upper side. Rotate •...
Page 15 DM-1505 3 – 7...
Page 16 DM-1505 3) Remove the drum fixing plate and the photoconductor drum. B. Drum unit (Note) Dispose the drum fixing plate which was removed. 1) Check the external view. • Check for damage or cracks on the boss and the boss hole. •...
Page 17 DM-1505 7) Clean the cleaning section and the waste toner pipe to remove 12) Attach the drum fixing plate and the photoconductor drum. waste toner completely with a vacuum cleaner. Apply grease to the inside of the photoconductor drum. (Dia. 2) 8) Remove the felt and duplex tape completely.
Page 18 DM-1505 EXTERNAL VIEWS AND INTERNAL STRUCTURES 1. Appearance Original cover DM-1500 DM-1505 Original cover Side cover Bypass tray Bypass tray guides Side cover open button Front cover Paper tray Operation panel Original table Handle PCL printer interface Paper output tray Paper output tray extension Handle Power switch...
Page 19 DM-1505 3. Operation panel 12 13 Exposure mode selector key and indicators Duplex Mode select key and indicator Use to sequentially select the exposure modes: AUTO, (DM-1505 only) MANUAL or PHOTO. Selected mode is shown by a lit indicator. Alarm indicators Light and dark keys and exposure indicators :Drum replacement required indicator Use to adjust the MANUAL or PHOTO exposure level.
Page 20 DM-1505 4. Motors and solenoids Part name Control signal Function,operation Main motor Drives the copier. Mirror motor MRMT Drives the optical mirror base (scanner unit). Toner motor Supplies toner. Cooling fan motor Cools the optical section. Resist roller solenoid Resist roller rotation control solenoid Paper feed solenoid CPFS1 Cassette Paper feed solenoid...
Page 21 DM-1505 5. Sensors and switches Name Signal Type Function Output Mirror home position Mirror (scanner unit) MHPS Transmission sensor “H” at home position sensor home position detection POD sensor Transmission sensor Paper exit detection “H” at paper pass Paper transport detection PPD2 sensor PPD2 Transmission sensor...
Page 22 DM-1505 6. PWB unit Name Function Exposure lamp invertor PWB Exposure lamp (Xenon lamp) control Main PWB (MCU) Copier control Operation PWB Operation input/display Power PWB AC power input, DC voltage control, High voltage control CCD sensor PWB For image scanning LSU motor PWB For polygon motor drive TCS PWB...
Page 23 DM-1505 7. Cross sectional view Part name Function and operation Illuminates the original with the copy lamp and passes the reflected light to the lens unit Scanner unit (CCD). Exposure lamp Exposure lamp (Xenon lamp) Illuminates original Lens unit Scans the original image with the lens and the CCD. LSU (Laser unit) Converts the original image signal into laser beams and writes onto the drum.
Page 24: Copier Installation
DM-1505 8"(20cm) UNPACKING AND INSTALLATION 8"(20cm) 1. COPIER INSTALLATION Improper installation may damage the copier. Please note the following 4" 4" during initial installation and whenever the copier is moved. (10cm) (10cm) Caution: If the copier is moved from a cool place to a warm place, condensation may form inside the copier.
Page 25: Installing The Td Cartridge
DM-1505 3. CHECKING PACKED COMPONENTS 6. INSTALLING THE TD CARTRIDGE AND ACCESSORIES The TD cartridge replacement required ( ) indicator will light up when toner is needed. If copying is continued while the indicator Open the carton and check if the following components and acces- is lit, copies will gradually become lighter until the copier stops and the sories are included.
Page 26: Loading Copy Paper
DM-1505 5) Hold the tab of the protective cover and pull the tab to remove the 2) Remove the pressure plate lock. Rotate the pressure plate lock in cover. the direction of the arrow to remove it while pressing down the pres- sure plate of the paper tray.
Page 27: Installing The Printer Driver
DM-1505 4) When using Windows 95 on a personal computer with plug & play*, 8. POWER TO COPIER the “Update Device Driver Wizard” window will appear. Insert the in- 1) Ensure that the power switch of the copier is in the OFF position. stallation CD-ROM into the CD-ROM drive.
Page 28 CD-ROM, click the Next button, follow the on-screen in- structions, and finally click the Finish button. 7) Windows driver file search will find the device “SHARP AR-150 Series PCL”. Click the Next button and follow the on-screen instruc- tions.
Page 29: Test Printing
Uninstall AR-150 Series PCL The printer driver can be uninstalled. If the driver is uninstalled, printing can no longer be performed on the printer. For proper uninstallation, be sure to use the SHARP uninstall program of the printer driver group. Readme The latest information on the printer driver is included in this document.
Page 30: Outline Of Operation
DM-1505 [6] OPERATIONAL DESCRIPTIONS 1. Outline of operation The outline of operation is described referring to the basic configuration. (Basic configuration) Scanner section Operation section MCU (Main control/image process section) PCL control PCL I / F LSU (Laser unit) Laser diode, Polygon mirror lens Laser beam Paper exit Fusing section...
Page 31: Laser Unit
DM-1505 2. Scanner section Sub scanning direction Sensor scanning area A. How to scan documents Main The scanner has sensors that are arranged in a line. These sensors scan a scanning certain area of a document at a time and deliver outputs sequentially. When direction the line is finished, the next line is scanned, and this procedure is repeated.
Page 32: Fuser Section
DM-1505 4. Fuser section Component Function Semiconductor laser Generates laser beams. Converges laser beams in Collimator lens parallel. Polygon mirror, Reflects laser beams at a polygon motor constant rpm. BD (Mirror, lens, Detects start timing of laser PWB) scanning. Converges laser beams at a spot on the drum.
Page 33: Paper Feed Section And Paper Transport Section
DM-1505 2. The surface temperature of the upper heat roller is set to 165˚C ∼ (3) Thermal control 1. The heater lamp, thermistor, main PWB, DC power supply PWB, 190˚C. The surface temperature during the power save mode is set and triac within the power supply unit are used to control the to 100˚C.
Page 34 DM-1505 (1) Cassette paper feed operation 5) At this time, the paper is fed passed the paper entry detection 1) The figure below shows the positions of the pick-up roller, the paper switch (PPD1), and detected by it. After about 0.15 sec from detec- feed clutch sleeve, and the paper feed latch in the initial state tion of paper by PPD1, the tray paper feed solenoid (PFS) turns on without pressing the COPY button after lighting the ready lamp.
Page 35 DM-1505 (2) Manual multi paper feed operation 1) Before paper feed operation, the manual paper feed solenoid (MPFS) is turned OFF as shown in the figure below. MPFS 4) The lead edge of the transported paper is pressed on the resist MPFS roller by the transport roller.
Page 36 DM-1505 1) POD does not turn on within 2.9 sec c. POD jam 7. D-D (Duplex to Duplex) mode paper/ after turning on the resist roller. document transport (DM-1505 only) 2) POD does not turn off within 1.5 sec ∼ 2.7 sec after turning off PPD2.
Page 37 DM-1505 Switchback operation is made after back copying in order to discharge C. Back copy documents according to the setting. Document transport: By switchback operation, the document is sent Set document Documents after discharge, through the PS roller to the exposure section, where the back of the document is exposed.
Page 38: High Voltage Section
DM-1505 (2) Push up the lock pawls (2 positions) of the side cover, and remove [7] DISASSEMBLY AND ASSEMBLY the transfer charger. Before disassembly, be sure to disconnect the power cord for safety. The disassembly and assembly procedures are described for the fol- Lock pawl rear lowing sections: 1.
Page 39: Operation Panel Section
DM-1505 (2) Set the charger cleaner to the transfer unit, and move it reciprocal- 2. Operation panel section ly a few times in the arrow direction shown in the figure below. A. List Part name Ref. Operation panel unit Operation PWB B.
Page 40: Optical Section
DM-1505 (2) Remove the screws (2pcs.), and remove the copy lamp unit from C. Assembly procedure the mirror base drive wire. For assembly, reverse the disassembly procedure 3. Optical section A. List Part name Ref. Copy lamp unit Copy lamp Lens unit B.
Page 41: Fusing Section
DM-1505 (5) Remove the screws (2 pcs.), the harness, and the optical unit. 4. Fusing section A. List Part name Ref. Thermistor PPD2 sensor Heater lamp Pressure roller Heat roller B. Disassembly procedure (1) Remove the connectors (3 pcs.) of the rear cabinet. (2) Open the side cover, remove two screws, and remove the fusing unit.
Page 42 DM-1505 (4) Remove the screw and remove the U-turn guide. (7) Remove the plate spring on the right and remove the heater lamp. Pressure roller section disassembly Hearter lamp Remove the three screws, remove the fusing cover lower on the right side, and open the heat roller section.
Page 43 DM-1505 (10) Remove the pressure release levers on the right and the left (6) Remove the C-ring and the fusing bearing, and remove the heat sides. roller. Heat roller (7) Remove the parts from the heat roller. Note: Apply grease to the sections specified with ✽. (11) Remove the pressure roller, the pressure bearing, and the spring.
Page 44 DM-1505 (3) Remove two screws and remove the toner motor. 5. Tray paper feed/transport section A. List Part name Ref. PPD1 sensor PWB LSU unit Intermediate frame unit Paper feed roller B. Disassembly procedure (1) Remove six connectors and screws of the main PWB, and lift the optical unit and the main PWB to remove.
Page 45 DM-1505 (5) Remove the pulleys on the both sides and remove the paper exit (7) Release the belt pulley (a) lock and remove the belt pulley bearing. roller. (8) Remove the paper exit roller. (6) Pull out the paper exit roller knob and remove the belt. 7 –...
Page 46 DM-1505 (9) Remove the harness guide. (11) Remove the parts as shown below, and remove the pressure release solenoid and the paper feed solenoid. (10) Remove five screws and remove the main drive plate and the belt. (12) Remove six screws and remove the LSU unit. CAUTION:Attach the gears securely...
Page 47 DM-1505 (13) Remove two screws and remove the fusing connector. (17) Remove three screws and remove the TC front paper guide. (14) Remove five screws and the connector, and lift the intermediate frame unit to remove. (18) Remove the screw and the connector, and remove the PPD1 sensor PWB.
Page 48: Manual Paper Feed Section
DM-1505 (19) Remove two E-rings and remove the paper feed roller. 6. Manual paper feed section (20) Remove three E-rings and remove the clutch unit. A. List Part name Ref. Back Manual transport roller Cassette detection switch PPD1 sensor PWB Side door detection unit Clutch unit B.
Page 49 DM-1505 (2) Remove the screw and remove the side door detection unit. (4) Remove the PPD1 sensor PWB. Back Wire treatment (3) Remove three screws and remove the single manual feed upper frame. Wire treatment (5) Remove the E-ring and remove the manual paper feed transport roller.
Page 50 DM-1505 (6) Remove the cassette detection switch. Multi unit (1) Remove the screw and remove the multi upper cover. Wire treatment (2) Remove the screw and remove the side door detection unit. (7) Remove the multi cover. Orange Multi cover Back Wire treatment manuals4you.com...
Page 51 DM-1505 (3) Remove three screws and remove the multi paper feed upper (5) Remove three E-rings and remove the manual paper feed roller frame. (4) Remove two screws and remove the multi feed bracket unit from the multi paper feed upper frame. (6) Remove the pick-up roller.
Page 52: Rear Frame Section
DM-1505 (7) Cut the binding band and remove the multi paper feed solenoid. 7. Rear frame section A. List Part name Ref. Mirror motor Main motor Exhaust fan motor B. Disassembly procedure (1) Remove three screws and remove the rear cabinet. Multi paper feed solnoid C.
Page 53: Power Section
DM-1505 (3) Remove two screws and one harness, and remove the main 8. Power section motor. A. List Part name Ref. Power PWB B. Disassembly procedure (1) Remove two screws and one connector, and remove the power PWB. C. Assembly procedure (4) Remove two screws and one connector, and remove the exhaust For assembly, reverse the disassembly procedure.
Page 54 DM-1505 1) Remove the belt, the paper feed frame SP, and two harnesses. B. Pickup solenoid 2) Remove the pickup unit. 1) Remove two screws. 2) Remove the pickup solenoid ∗ When installing, hang iron core A on the solenoid arm. C.
Page 55 DM-1505 D. Manual paper feed roller, pickup roller E. Belt 1) Lift the paper stopper. 1) Remove the belt. 2) Slide the takeup roller unit. 3) Slide the bush in the arrow direction. 4) Remove the takeup roller unit. F. SPF motor 1) Remove the harness.
Page 56: Nd Cassette Section
DM-1505 1) Open the right cabinet. H. PS roller 2) Remove three screws. 1) Remove the parts. 3) Remove one connector. 2) Remove the PS roller. 4) While tilting down the 2nd connection arm A, pull and remove the paper feed unit toward you. I.
Page 57 DM-1505 B. Cassette detection SW E. Paper feed clutch 1) Remove the pawl. 1) Remove the E-ring. 2) Remove the cassette detection SW. 2) Remove the paper feed clutch. 3) Remove the harness. 3) Remove the parts. C. Paper feed solenoid 1) Remove the screw.
Page 58 DM-1505 11. DUP motor section (DM-1505 only) 12. Reverse roller section (DM-1505 only) A. Remove the rear cabinet. A. Remove the reverse unit. 1) Remove four screws. 1) Remove four screws 2) Remove the rear cabinet. 2) Remove the spring, and the earth wire 3) Remove the reverse unit.
Page 59 DM-1505 (3) Remove the RSPF. D. Pickup unit 1) Remove the connector and the cable. 1) Remove the belt, the paper feed frame spring, and two harnesses. 2) Remove the RSPF. 2) Remove the pickup unit. B. Intermediate tray 1) Remove the intermediate tray. NOTE: When reassembling, be careful of the hole position for the paper feed frame spring.
Page 60 DM-1505 F. Sensor PWB H. Clutch 1) Remove two screws. (1) Remove the clutch unit. 2) Remove the sensor PWB. 1) Remove the E-ring. 3) Remove the harness. 2) Remove the pulley and the bush. 3) Slide the bush in the arrow direction. 4) Lift the clutch pawl.
Page 61 DM-1505 I. Manual paper feed roller, pickup roller J. Transport unit removal (1) Remove the pickup unit. 1) Remove the harness. 1) Lift the paper stopper. 2) Remove two screws. 2) Slide the takeup roller unit. 3) Remove the document tray unit. 3) Slide the bush in the arrow direction.
Page 62 DM-1505 L. Belt 2 O. Clutch 1) Remove three screws. 1) Cut the band with nippers. 2) Remove the drive unit. 2) Remove the harness. 3) Remove 3) Remove the clutch. NOTE: When reassembling, hang the belt on the boss. M.
Page 63 DM-1505 (2) Remove the PS roller. R. Transport roller1. 1) Loosen the screw. (1) Remove the parts. 2) Open the paper exit PG. 1) Remove the parts. 3) Remove the parts. 4) Remove the PS roller. (2) Remove the parts. 1) Loosen the screw.
Page 64 DM-1505 S. Paper exit roller T. Solenoid (1) Remove the parts. (1) Remove the reverse gate 1) Remove two screws. 1) Remove the ring 2) Remove the parts. 2) Remove the reverse gate (2) Remove the paper feed PG upper. 1) Remove two screws.
Page 65 DM-1505 d. Adjustment procedure [8] ADJUSTMENTS 1) Remove the right cabinet (manual paper feed unit), the docu- 1. Optical section ment reference plate. 2) Remove the document glass. A. Image distortion adjustment There are following two types of image distortion. Horizontal image distortion Vertical image distortion In this machine, the image distortion is adjusted by changing the paral-...
Page 66 DM-1505 7) Manually turn the copy lamp unit/No.2/3 mirror unit drive gear to bring No.2/3 mirror unit into contact with the positioning plate, and perform the procedure of step 4). Repeat procedures of steps 4) to 7) until the parallelism of No.2/3 mirror unit is properly set.
Page 67 DM-1505 10) Check the horizontal image distortion. (2) Vertical image distortion adjustment If LL = LR, there is no horizontal distortion a. Summary In this adjustment, the left and right balance is adjusted by changing LL and LR: Distance between the copy the left and right balance of the No.
Page 68 DM-1505 3) If the right-left distortion balance is improper, loosen the fixing (1) Outline screw of No.2/3 mirror unit rail to change and adjust the right-left The main scanning (front/rear) direction magnification ratio adjust- balance of No.2/3 mirror unit rail. ment is made automatically or manually.
Page 69 DM-1505 4) Measure the length of the copied scale image. 5) Calculate the main scanning direction magnification ratio. Main scanning direction magnification ratio Copy image dimensions × 100 (%) Original dimension (When a 100mm scale is used as the original.) Original (Scale) HARDDENCD STAINLESS...
Page 70 DM-1505 Original (Scale) HARDDENCD STAINLESS JAPAN 1/2mm Shizuoka Paper feed HARDDENCD direction STAINLESS JAPAN 1/2mm Shizuoka Reference Comparison point Copy 6) Check that the actual copy magnification ratio is within the D. Image position adjustment specified range. (100 ± 1.0%). There are following five kinds of image position adjustments, which are If it is not within the specified range, perform the following pro- made by laser control except for the image scan start position adjust-...
Page 71 DM-1505 (1) Lead edge adjustment 3) Make a copy and measure the void amount of image rear edge. 1) Set a scale to the center of the paper lead edge guide as shown below, and cover it with B4 or 8 1/2″ × 14″ paper. Void amount (Standard value: 2 –...
Page 72: Copy Density Adjustment
D. Features of copy density adjustment For the copy density adjustment, the image data shift function provided in the image process LSI is used. Adjustment Exposure mode Sharp gray chart posure mode display lamp adjustment level List of the adjustment modes level “3”...
Page 73: High Voltage Adjustment
B. DV bias adjustment Check the adjustment level (shown in the above table) of the ex- Note: posure test chart (Sharp Gray Scale). A digital multi meter with internal resistance of 1GΩ must be use for correct adjustment. Sharp Gray Scale adjustment level...
Page 74 DM-1505 2) Set the test chart so that the scale is positioned as shown below, (Adjustment procedure) in the S-D mode and the D-S mode. (1) Paper trailing edge void quantity 1) Preparing test chart (Draw a scale at the rear end of one side of a sheet of A/4 white paper or letter paper) Scale (S-D mode) Scale (D-S mode)
Page 75: List Of Simulations
DM-1505 [9] SIMULATION TROUBLE CODES 1. List of simulations The simulations for the AR-F151 (with Fax functions) are shown in bold fonts. Kind of Kind of Operation Operation main code code main code code Optical Mirror scan operation Various Manual feed setup system setup SPF setup...
Page 76 DM-1505 2. Contents of simulations (new or revised simulations only) Input method: Clear key → Exposure Select key → Clear key → Exposure Select key Main code Sub code Content Mirror scan operation (Operation/Procedure) 1. When this simulation is executed, the mirror home position is detected. Sensor name Display lamp Mirror home position sensor...
Page 77 DM-1505 Main code Sub code Content Warm-up display and aging with jam (Operation/Procedure) 1. When the simulation is executed, warming up is started. 2. Warm-up time is counted and displayed every second on the copy quantity display. 3. After completion of warm-up, the time count is stopped and the ready lamp is lighted. 4.
Page 78 DM-1505 Main code Sub code Content DV counter display The display method is the same as the total count value display. SPF counter display The display method is the same as the total count value display. Drum counter display The display method is the same as the total count value display. P-ROM versiondisplay The P-ROM version is displayed in 3 digits on the value display section.
Page 79 DM-1505 Main code Sub code Content SPF setup When this simulation is executed, the currently set SPF code number is displayed. Enter the code number of the SPF to be set and press the PRINT switch. The setup is changed. Code No.
Page 80 DM-1505 Main code Sub code Content Cancel of stop at drum life over (Operation/Procedure) 1. When this simulation is executed, the currently set code number is displayed. 2. Enter the code number and press the START key, and the setting will be changed. Code number Setting Stop at drum life over...
Page 81 DM-1505 Main code Sub code Content Side void setup (Operation/Procedure) 1. When this simulation is executed, the currently set code number of the side void amount is displayed. 2. Enter the code number and press the start key. The setting is changed. Code number Setting 0 mm...
Page 82 DM-1505 Main code Sub code Content Fusing temperature setup 2 (Operation/Procedure) 1. When this simulation is executed, the currently set code number is displayed. 2. Enter the code number and press the START key, and the setting will be changed. Code number Set temperature (˚C) 170 (∗...
Page 83 DM-1505 Main code Sub code Content Relationship between the displayed values and the GAMMA ADJUST register Exp1 Exp2 Exp3 Exp4 Exp5 –24 –12 TEXT –24 –12 PHOTO –24 –12 –24 –12 The value displayed after execution of this simulation can be set in the range of 0 – 99 with 50 as the center value.
Page 84 DM-1505 Main code Sub code Content Lead edge image position adjustment + Paper lead edge/rear edge void adjustment (Outline) This adjustment is used to adjust the copy image position and lead edge/rear edge void amount on the copy paper by adjusting the image scan start position and the print start position (resist roller ON timing) at 100%. (Operation/Procedure) 1.
Page 85 DM-1505 Main code Sub code Content Paper center offset + OC/Document center offset + SPF document center offset (Outline) The center offset position of copy image on the copy paper and that of document scan are adjusted by adjusting the scan left margin of ASIC and the print left margin register set value. (Operation/Procedure) 1.
Page 86 DM-1505 Main code Sub code Content Duplex copy rear edge void adjustment Used to adjust the rear edge void in duplex copy. (Operating procedure) When this simulation is executed, the currently set value is displayed in 2 digits. When the copy mode select key is pressed, the set mode and the display are switched sequentially. Enter the adjustment value with the 10-key and press the print key, and the entered value is stored and a copy is made.
Page 87: Trouble Codes
DM-1505 Main code Sub code Content Shading check (Outline) Used to display the detection level of the white plate for shading. (Vref of AD conversion IC is fixed.) (Operation/Procedure) When the START key is pressed, the mirror base unit moves to the white plate for shading and Vref+ voltage of AD conversion IC is set to 4.5V and Vref- voltage to 0.5V, and the copy lamp is lighted.
Page 88 DM-1505 Main Trouble content Detail of trouble code code Main motor lock When the main motor encoder pulse is not detected for 100msec. Polygon motor lock The lock signal (specified rpm signal) does not return within a certain time (about 20sec) from starting the polygon motor rotation Thermistor open detection The fusing thermistor is open.
Page 89 DM-1505 [10] USER PROGRAM The conditions of factory setting can be changed according to the use conditions. Functions which can be set with the user program Function Contents Factory setting When a certain time is passed after completion of copying, this function returns to the initial state Auto clear.
Page 90 DM-1505 [11] ELECTRICAL SECTION 1. Block diagram A. Overall block diagram 11 – 1 manuals4you.com...
Page 91 DM-1505 B. MCU PWB unit 11 – 2...
Page 92: Circuit Descriptions
DM-1505 2. Circuit descriptions A. Man PWB (MCU) (1) CPU signal table Signal Signal Input/output Operating Input/output Operating code code /CS1 Output Chip Select for SRAM /CS0 Output Chip Select for EPROM Data Data Bus input/output D-GND Data Data Bus D-GND input/output Data...
Page 93 DM-1505 Signal Signal Input/output Operating Input/output Operating code code Input Print switch input SIN4 Input Sensor input 4 KIN1 Input Key input 1 Analog Reference Voltage (High) for output KIN2 Input Key input 2 Analog Reference Voltage (Low) for TMCLK Timer output Clock for Toner Motor output...
Page 94 DM-1505 (2) ASIC (Signal table) PIN No. Signal name IN/OUT Connected to Description /SCANSP CPU (I/O) Scanner process interrupt signal /PRSTART Print start trigger signal /TMEN Toner motor ON/OFF TMCLK Toner motor reference clock 3.3V Power CPUAD7 CPU address bus CPUAD6 CPU address bus Power...
Page 95 DM-1505 PIN No. Signal name IN/OUT Connected to Description Power MAD1 DRAM Address bus of DRAM (page memory) MAD2 DRAM Address bus of DRAM (page memory) MAD3 DRAM Address bus of DRAM (page memory) MAD4 DRAM Address bus of DRAM (page memory) MAD5 DRAM Address bus of DRAM (page memory)
Page 96 DM-1505 PIN No. Signal name IN/OUT Connected to Description /FAXCS Reserved ∗ Electric sort board /ESPRD (Reserved) (Reserved) Power ∗ Electric sort board /ESREQ (Reserved) (Reserved) ∗ Electric sort board /ESACK (Reserved) (Reserved) ∗ Electric sort board /ESCS (Reserved) (Reserved) PARAD0 IN/OUT 1284 board connector DATA bus (IEEE1284 communication port)
Page 97 DM-1505 PIN No. Signal name IN/OUT Connected to Description SOE0 SRAM (separation) Read enable line to SRAM before area separation SWE0 SRAM (separation) Write enable line to SRAM before area separation SCS0 SRAM (separation) Chip select line to SRAM before area separation SD00 IN/OUT SRAM (separation)
Page 98 DM-1505 PIN No. Signal name IN/OUT Connected to Description Power CCD PWB (AD IDIN7 Image scan data (after 8bit A/D conversion) conversion) /SDCLK CHECK Effective image area signal Power SFCLK Transmitter CCD drive clock (48MHz), Also used as an internal clock. TEST port 0 AUTO SCAN TEST High: Normal Low: Test...
Page 99 DM-1505 PIN No. Signal name IN/OUT Connected to Description Tr array IC Toner motor drive output (–) CPUD15 IN/OUT CPU data bus CPUD14 IN/OUT CPU data bus CPUD13 IN/OUT CPU data bus CPUD12 IN/OUT CPU data bus CPUD11 IN/OUT CPU data bus Power CPUD10 IN/OUT...
Page 100 DM-1505 Table A (Signals used in the FAX PWB) Table B (Signals used in PCL PWB) PIN No. Signal PIN No. Signal IN/OUT Descriptions IN/OUT Descriptions (CN5) name (CN5) name /SCLINE Effective input image area /PREADY PCL PWB recognition signal FTXD Serial communication data FTXD...
Page 101 DM-1505 3. PCL PWB Block diagram A. Overall block diagram 11 – 12...
Page 102 DM-1505 Operational descriptions 4. Block diagram functional descriptions Connected to PARACONN or USBCONN of PCL I/F PWB Descriptions of each block (CPWBF0057QS51). Print data made by page description language is inputted from an ex- PCL PWB Controls PCL print. ternal device. Control IC The PCL I/F PWB (CPWBF0057QS51) is provided with two kinds of Chipset ASIC...
Page 103 DM-1505 CPU (VHIIDT79RC465) I/O pin arrangement list (PCL Model) Pin name Signal name IN/OUT Destination Function N.C, SYSAD11 SYSAD11 IN/OUT ASIC(KZ4H167V06), 16M FLASH, System address data bus 8M FLASH, 74LVC16245 3.3V Power source SYSCMD8 SYSCMD8 ASIC (KZ4H167V06) System command data bus SYSAD42 SYSAD42 IN/OUT...
Page 104 DM-1505 Pin name Signal name IN/OUT Destination Function 3.3V Power source SYSCMD2 SYSCMD2 ASIC (KZ4H167V06) System command data bus SYSAD36 SYSAD36 IN/OUT ASIC(KZ4H167V06), 74LVC16244 System address data bus SYSAD4 SYSAD4 IN/OUT ASIC(KZ4H167V06), 16M FLASH, System address data bus 8M FLASH, 74LVC16245 SYSCMD1 SYSCMD1 ASIC (KZ4H167V06)
Page 105 DM-1505 Pin name Signal name IN/OUT Destination Function 3.3V Power source SYSAD17 SYSAD17 IN/OUT ASIC(KZ4H167V06), 16M FLASH, System address data bus 8M FLASH SYSAD49 SYSAD49 IN/OUT ASIC (KZ4H167V06), 74LVC244 System address data bus INT0 INTR0_ ASIC(KZ4H167V06) ASIC interruption 0 SYSAD18 SYSAD18 IN/OUT ASIC(KZ4H167V06), 16M FLASH,...
Page 106 DM-1505 Pin name Signal name IN/OUT Destination Function SYSAD23 SYSAD23 IN/OUT ASIC(KZ4H167V06), 16M FLASH, System address data bus 8M FLASH SYSAD55 SYSAD55 IN/OUT ASIC (KZ4H167V06) System address data bus NMI_ ASIC(KZ4H167V06) Non-maskable interruption 3.3V Power source SYSADC2 3.3V Power source SYSADC6 3.3V Power source...
Page 107 DM-1505 Pin name Signal name IN/OUT Destination Function SYSAD30 SYSAD30 IN/OUT ASIC(KZ4H167V06), 16M FLASH, System address data bus 8M FLASH 3.3V Power source SYSAD62 SYSAD62 IN/OUT ASIC (KZ4H167V06) System address data bus SYSAD31 SYSAD31 IN/OUT ASIC(KZ4H167V06), 16M FLASH, System address data bus 8M FLASH SYSAD63 SYSAD63...
Page 108 DM-1505 ChipsetASIC (VHIKZ4H167V06) I/O pin arrangement list (PCL Model) Pin name Signal name IN/OUT Destination Function 3.3V Power source SYSAD16 SYSAD16 IN/OUT CPU, 16M FLASH, 8M FLASH System address data bus SYSAD17 SYSAD17 IN/OUT CPU, 16M FLASH, 8M FLASH System address data bus SYSAD18 SYSAD18 IN/OUT...
Page 109 DM-1505 Pin name Signal name IN/OUT Destination Function SYSAD51 SYSAD51 IN/OUT CPU, 74LVC244 System address data bus 3.3V Power source SYSAD52 SYSAD52 IN/OUT CPU, 74LVC244 System address data bus SYSAD53 SYSAD53 IN/OUT CPU, 74LVC244 System address data bus SYSAD54 SYSAD54 IN/OUT System address data bus SYSAD55...
Page 110 DM-1505 Pin name Signal name IN/OUT Destination Function /DACK1 /DACK0 PARACK_ ASIC(KZ3H008302) ACK_ signal to interface ASIC /CPURST CPURST_ CPU reset signal /CRST COLDRES_ Cold reset signal VCCOK VCCOK CPU, ASIC(KZ3H008302) states effective 3.3V Power source /NMI NMI_ Non-maskable interruption output /INTR2 INTR2_ Interruption output 2...
Page 111 DM-1505 Pin name Signal name IN/OUT Destination Function /CAS6 CAS6_ 16M Flash, DIMM168 DRAM CAS_ signal /CAS5 CAS5_ 16M Flash, DIMM168 DRAM CAS_ signal /CAS4 CAS4_ 16M Flash, DIMM168 DRAM CAS_ signal /CAS3 CAS3_ 16M Flash, DIMM168 DRAM CAS_ signal /CAS2 CAS2_ 16M Flash, DIMM168...
Page 112 DM-1505 Pin name Signal name IN/OUT Destination Function 3.3V Power source MD51 MD51 IN/OUT 16M Flash, DIMM168 DRAM data signal MD19 MD19 IN/OUT 16M Flash, DIMM168 DRAM data signal MD50 MD50 IN/OUT 16M Flash, DIMM168 DRAM data signal MD18 MD18 IN/OUT 16M Flash, DIMM168 DRAM data signal...
Page 113 DM-1505 Pin name Signal name IN/OUT Destination Function IN/OUT 16M Flash, DIMM168 DRAM data signal MD33 MD33 IN/OUT 16M Flash, DIMM168 DRAM data signal IN/OUT 16M Flash, DIMM168 DRAM data signal MD32 MD32 IN/OUT 16M Flash, DIMM168 DRAM data signal IN/OUT 16M Flash, DIMM168 DRAM data signal...
Page 114 DM-1505 Pin name Signal name IN/OUT Destination Function SYSAD3 SYSAD3 IN/OUT CPU, 16M FLASH, 8M FLASH, System address data bus 74LVC16245 SYSAD4 SYSAD4 IN/OUT CPU, 16M FLASH, 8M FLASH, System address data bus 74LVC16245 SYSAD5 SYSAD5 IN/OUT CPU, 16M FLASH, 8M FLASH, System address data bus 74LVC16245 SYSAD6...
Page 115 DM-1505 Interface ASIC (VHIKZ3H008302) I/O pin arrangement list (PCL Model) Pin name Signal name IN/OUT Destination Function 3.3V Power source CPUD13 LDT13 IN/OUT 74LVC16245 Data bus CPUD14 LDT14 IN/OUT 74LVC16245 Data bus CPUD15 LDT15 IN/OUT 74LVC16245 Data bus MODECLK MODECLK 74LS244 Boot mode clock MODEIN...
Page 116 DM-1505 Pin name Signal name IN/OUT Destination Function PARAD5 PARAD5 74LCX245, USS-725 Parallel I/F data bus PARAD4 PARAD4 74LCX245, USS-725 Parallel I/F data bus PARAD3 PARAD3 74LCX245, USS-725 Parallel I/F data bus PARAD2 PARAD2 74LCX245, USS-725 Parallel I/F data bus 3.3V Power source PARAD1...
Page 117 DM-1505 [12] CIRCUIT DIAGRAM AVcc P35/SCK1 R208 20KJ Vref P34/SCK0 P40/AN0 P33/RxD1 P41/AN1 P32/RxD0 P42/AN2 P31/TxD1 R201 20KJ P43/AN3 P30/TxD0 P44/AN4 BR36 BR40 20KJ P45/AN5 PD7/D15 P46/AN6/DA0 PD6/D14 P47/AN7/DA1 PD5/D13 AVss PD4/D12 BR37 BR41 20KJ P17/PO15/TIOCB2/TCLKD PD3/D11 P16/PO14/TIOCA2 PD2/D10 P15/PO13/TIOCB1/TCLKC PD1/D9 P14/PO12/TIOCA1 PD0/D8...
Page 118 DM-1505 R193 R194 R195 12 – 2 manuals4you.com...
Page 119 DM-1505 12 – 3...
Page 120 DM-1505 12 – 4 manuals4you.com...
Page 121 DM-1505 SD10 SD11 (6-D1) SD12 (6-D1) SD13 /CAS1 (6-E1) /CAS0 (6-E1) SD14 (6-E1) SD15 SD16 MAD11 (6-E1) SD17 MAD10 (6-E1) MAD9 (6-E1) (5-E4) SOE[1] MAD8 MAD7 (5-E4) (6-E1) SWE[1] (5-E4) MAD6 (6-E1) SCS[1] (6-E1) (5-D4) MAD5 SOE[0] MAD4 (5-D4) (6-E2) SWE[0] (6-E2) (5-D4)
Page 122 DM-1505 12 – 6 manuals4you.com...
Page 123 DM-1505 12 – 7...
Page 124 DM-1505 12 – 8 manuals4you.com...
Page 125 DM-1505 12 – 9...
Page 126 DM-1505 12 – 10 manuals4you.com...
Page 127 DM-1505 12 – 11...
Page 128 DM-1505 12 – 12 manuals4you.com...
Page 129 DM-1505 12 – 13...
Page 130 DM-1505 12 – 14 manuals4you.com...
Page 131 DM-1505 12 – 15...
Page 132 DM-1505 12 – 16 manuals4you.com...
Page 133 DM-1505 12 – 17...
Page 134 DM-1505 12 – 18 manuals4you.com...
Page 135 DM-1505 7 GND 9 E1 10 E2 13 OC 6 RT 5 CT 2 -I1 14 RefOut 3 FBack DTCon 12 – 19...
Page 136 DM-1505 12 – 20 manuals4you.com...
Page 137 DM-1505 12 – 21...
Page 138 DM-1505 12 – 22 manuals4you.com...
Page 139 DM-1505 12 – 23...
Page 140 DM-1505 12 – 24 manuals4you.com...
Page 141 Base plate unit 2 MCU PWB Fusing unit DC power supply PWB Drive unit Index Multi manual feeding cover unit This document has been published to be SHARP CORPORATION used for after sales service only. The contents are subject to change without notice.
Page 142 DM-1505 DEFINITION The definition of each Rank is as follows and also noted in the list A : Parts necessary to be stocked as High usage parts. B : Parts necessary to be stocked as Standard usage parts. C : Low usage parts. D : Parts necessary for refurbish.
Page 143 DM-1505 1 Exteriors FCPN0025 – 2 –...
Page 144 DM-1505 2 R-SPF exteriors(DM1505) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 L S O U - 0 0 0 4 Q S Z Z Original tray 2 L P L T P 0 0 1 1 Q S Z Z Control plate F 3 L P L T P 0 0 1 2 Q S Z Z Control plate R...
Page 145 DM-1505 2 R-SPF exteriors(DM1505) 36 35 26 27 FCPN0026 – 4 –...
Page 146 DM-1505 3 R-SPF pick up unit(DM-1505) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 G C A B - 0 0 0 8 Q S Z Z Open and shut exterior 2 P S P O - 0 0 0 2 Q S Z Z Stopper sponge 4 M A R M P 0 0 0 3 Q S Z 1 Stopper arm...
Page 147: Table Of Contents
DM-1505 4 R-SPF transport unit(DM-1505) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 P S H E Z 2 1 7 4 F C Z Z Paper feeding sheet 2 P S H E Z 0 0 3 9 Q S Z Z Sheet 3 L P L T P 0 0 1 3 Q S Z Z Plate...
Page 148 DM-1505 5 SPF exteriors(DM1500) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 L S O U - 0 0 0 4 Q S Z Z Original tray 2 L P L T P 0 0 1 1 Q S Z Z Control plate F 3 L P L T P 0 0 1 2 Q S Z Z Control plate R...
Page 149 DM-1505 6 R-SPF pick up unit(DM-1500) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 G C A B - 0 0 0 8 Q S Z Z Open and shut exterior 2 P S P O - 0 0 0 2 Q S Z Z Stopper sponge 4 M A R M P 0 0 0 3 Q S Z 1 Stopper arm...
Page 150 DM-1505 7 R-SPF transport unit(DM-1500) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 P G I D M 0 0 4 2 Q S Z Z U-turn paper guide 2 X E B S D 3 0 P 1 2 0 0 0 Screw (3 12) 3 L X - B Z 0 0 1 2 Q S Z Z Screw...
Page 151: E B S
DM-1505 8 Operation panel PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK P F I L Z 0 0 0 7 Q S Z 9 Operation filter (DM1500) P F I L Z 0 0 0 7 Q S 1 0 Operation filter (DM1505) 2 C B T N - 0 0 0 9 Q S 0 1...
Page 152: H B S E 3 0 P 0 6 0 0 0 Aa C Screw (3 6)
DM-1505 9 Side door unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK G C A B - 0 0 0 7 Q S Z Z Side door (DM1500) G C A B - 0 0 0 7 Q S Z 1 Side door (DM1505) 2 P T M E - 0 0 0 4 Q S Z Z...
Page 153 DM-1505 10 Optical frame 1 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 P W I R - 0 0 0 3 Q S Z Z MB wire 2 C H L D Z 0 0 1 9 Q S 3 1 2nd,3rd mirror holder unit 3 C R E F L 0 0 0 3 Q S 3 2 Copy lamp unit...
Page 154 DM-1505 11 Optical frame 2 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 X H B S E 3 0 P 0 8 0 0 0 Screw (3 8) 2 P C A S Z 0 0 0 3 Q S Z Z Dark box 3 D H A I - 0 0 4 1 Q S Z Z CL lead harness...
Page 155: B N D J 0 0 1 3 F C Z 1 Aa C Wire Band
DM-1505 12 LSU unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 X E B S D 3 0 P 1 2 0 0 0 Screw (3 12) 2 D H A I - 0 1 5 5 Q S Z 1 LSU harness 3 L B N D J 0 0 1 3 F C Z 1 Wire band...
Page 156 DM-1505 14 Delivery paper guide unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 N R O L P 0 0 4 6 Q S Z Z Delivery roller upper 2 M S P R T 0 0 2 0 Q S Z Z Delivery roller spring 4 C P W B F 1 1 7 7 F C 5 7 POD sensor PWB...
Page 157 DM-1505 15 Middle frame PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 26 L P I N S 0 0 1 0 Q S Z Z DV guide pin 28 L X - B Z 3 0 0 6 S C 0 S Screw (3 6) 29 X B B S D 3 0 P 0 8 0 0 0 Screw (3 8)
Page 158: R E S P 5 0 - 0 6 0 0 0 Aa C E Type Ring
DM-1505 16 Base plate unit 1 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 C P W B F 1 1 7 7 F C 5 8 PPD1 sensor PWB 2 M L E V P 0 0 0 6 Q S Z Z PS front actuator 3 M S P R C 0 0 2 6 Q S Z Z PS front actuator spring...
Page 159 DM-1505 16 Base plate unit 1 4 2 1 FCP04076 – 18 –...
Page 160 DM-1505 17 Base plate unit 2 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 L H L D Z 0 0 5 0 Q S Z Z PWB holder 3 X H B S E 3 0 P 0 6 0 0 0 Screw (3 6) 4 C P W B X 0 0 3 8 Q S 3 9 MCSC PWB...
Page 161 DM-1505 17 Base plate unit 2 5 0 1 FCPN0029 – 20 –...
Page 162: Fusing Unit
DM-1505 18 Fusing unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 P G I D M 0 0 2 3 Q S Z Z U-turn guide lower 2 V R H - S T 2 H B 1 5 7 K Resistor (1/2W 150M ) 3 P W I R - 0 0 0 1 Q S Z Z HR earth wire...
Page 163 DM-1505 18 Fusing unit FCP04078 – 22 –...
Page 164 DM-1505 19 Drive unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 X B B S D 4 0 P 0 6 0 0 0 Screw (4 6) 2 R M O T P 0 0 1 0 Q S Z Z Main motor 3 M S P R C 0 0 5 3 Q S Z Z Pulley spring...
Page 165 DM-1505 20 Multi manual feeding cover unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 C C L E Z 0 0 0 5 Q S 5 1 Charger cleaner unit 2 X E B S E 3 0 P 0 8 0 0 0 Screw (3 8) 3 P C O V P 0 0 2 3 Q S Z 1 Multi upper cover...
Page 166 DM-1505 21 Multi manual feeding unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 36 X E B S E 4 0 P 1 2 0 0 0 Screw (4 12) 37 L S T P P 0 3 0 0 F C Z Z Stopper plate 38 M A R M P 0 2 0 5 F C Z Z Arm B...
Page 167: Socket Holder Unit
DM-1505 22 Socket holder unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 L H L D Z 0 0 0 9 Q S D Z HV interface holder 2 C H A I - 0 0 3 2 Q S 5 1 MC harness unit 3 C H A I - 0 0 2 8 Q S 5 1 GB-MCFB harness unit...
Page 168 DM-1505 24 250 Sheet tray PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 L P L T M 5 1 0 6 F C Z Z Turning plate 250 2 P S H E Z 4 1 4 2 F C Z Z Rotation plate sheet 3 L H L D W 1 2 2 6 F C Z Z Turn fasner...
Page 169 DM-1505 25 2nd frame unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 G C O V A 0 0 0 5 Q S Z Z Front cover 2 X E B S E 4 0 P 1 2 0 0 0 Screw (4 12) 3 G C O V A 0 0 0 6 Q S Z Z Rear cover...
Page 170 DM-1505 26 2nd Paper feeding unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 N R O L P 0 0 1 9 Q S Z 1 Transport roller 2 N B R G Z 1 0 4 3 H C Z Z Bearing (B-F5-13) 3 X R E S P 4 0 - 0 6 0 0 0 E type ring...
Page 171: Aa C Screw (3 12)
DM-1505 27 DV cartridge unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 C B O X - 0 0 0 7 J S 5 6 TH box 2 R U N T K 0 0 0 1 Y S Z Z IC connector 3 P C A P H 0 0 0 3 Q S Z Z Toner cap...
Page 172 DM-1505 29 Packing material & accessories PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK S P A K A 0 0 6 3 Q S Z Z Top packing cushion L (DM1500) S P A K A 0 1 9 2 Q S Z Z Top packing cushion L (DM1505) S P A K A 0 0 6 2 Q S Z Z...
Page 173 DM-1505 30 PCL I/F PWB unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 Q C N C W 0 9 4 6 F C Z Z Connector (36pin) [CN1] 2 Q C N C W 1 1 2 4 L C 3 B Connector (32pin) [CN3] 3 Q C N C W 7 0 4 5 X C Z Z...
Page 174: Operation Pwb
DM-1505 31 PCL PWB unit PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK V R S - C Y 1 J D 1 0 3 J Resistor (1/16W 10K [R607,608,609,621,624,628,680,737] V R S - C Y 1 J D 1 0 3 J Resistor (1/16W 10K [R786,787,789,790,791,796,960,622] 41 V R S - C Y 1 J D 1 2 2 J...
Page 175 DM-1505 34 POD sensor PWB PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 1 D H A I - 0 0 3 4 Q S Z Z POD harness 2 L B N D J 0 0 3 7 F C Z 1 Wire band (T18S) 3 V C K Y P U 1 H B 1 0 2 K Capacitor (50WV 0.001 F)
Page 176 DM-1505 37 MCU PWB PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK Block resistor (20K 4 1/32W R M P T W 4 2 0 3 Q C J J [BR27,28,33,35,40,41,42,43,44,45,46,47,48,49] R M P T W 4 2 0 3 Q C J J Block resistor (20K 4 1/32W [BR50,52,53,62,63,68,70,72,73]...
Page 177 DM-1505 37 MCU PWB PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK V R S - C Y 1 J D 1 0 0 J Resistor (1/16W 10 [R106,107,108,109,110,111,112] V R S - C Y 1 J D 1 0 0 J Resistor (1/16W 10 [R128,130,131,132,157,158,159,160] V R S - C Y 1 J D 1 0 0 J...
Page 178 DM-1505 38 DC power supply PWB PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 23 Q P L G Z 0 5 5 7 P A Z Z Plug (B02P-NV) [CN10] 24 Q P L G Z 0 5 6 0 P A Z Z Plug (B04P-XL(Red)) [CN3] 25 Q P L G Z 0 5 9 8 P A Z Z...
Page 179 DM-1505 38 DC power supply PWB PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK 133 V R D - S T 2 C D 2 2 1 J Resistor ((ST)1/6S-220 [R105] 134 V R D - S T 2 C D 2 2 3 J Resistor ((ST)1/6S-22K [R11,132] 135 V R D - S T 2 C D 2 2 4 J...
Page 180 DM-1505 Index PRICE PART PARTS CODE RANK MARK RANK DHAI-0037QSZ1 15- 23 PRICE PART PARTS CODE RANK MARK RANK " DHAI-0040QSZZ CBOX-0002RS54 27-501 " 14- 10 CBOX-0007JS56 " CBTN-0004QS05 DHAI-0041QSZZ CBTN-0009QS01 " CCASP0001QS51 " 24-901 CCLEZ0005QS51 DHAI-0042QSZZ CCOVP0004YS51 " CDAIU0002QS01 DHAI-0045QSZZ 10- 12 19- 27...
Page 181 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK LBNDJ0013FCZ1 LSOU-0001QSZZ " LSOU-0002QSZZ 17- 32 21- 48 " 21- 21 LSOU-0003QSZZ 21- 49 " LSOU-0004QSZZ " " 26- 31 LBNDJ0037FCZ1 LSOU-0005QSZ3 5- 33 " LSOU-0006QSZZ "...
Page 182 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK MSPRC0047QSZZ NBRGM5006BCZZ 16- 31 2- 26 MSPRC0048QSZZ " 21- 41 4- 25 MSPRC0049QSZZ 21- 14 " 7- 19 MSPRC0050QSZZ NBRGP0260FCZ1 9- 25 18- 24 MSPRC0051QSZZ NBRGP0562FCZZ 23- 12 16- 19...
Page 183 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK NROLP0024QSZZ PGIDM0021QSZZ 3- 27 4- 38 " PGIDM0022QSZZ 6- 27 NROLP0025QSZZ 9- 24 PGIDM0023QSZZ NROLP0046QSZZ PGIDM0024QSZ2 7- 30 NROLP1008FCZZ PGIDM0042QSZZ NROLP1060FCZZ PGIDM0057QSZZ 25- 11 4- 10 NROLP1122FCZZ 9- 17 PGLSP0001QSZZ...
Page 184 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK PSHEZ2174FCZZ RC-EZ0502PAZZ 38- 30 " RC-EZ0574PAZZ 7- 25 38- 31 " 16- 36 RC-EZ0577PAZZ 38- 32 PSHEZ4142FCZZ RC-EZ0580PAZZ 38- 35 PSPAZ0017QSZZ RC-FZ159DPAZZ 15- 32 38- 36 PSPO-0001QSZZ RC-FZ160DPAZZ 2- 37...
Page 185 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RTRNZ0484PANH VCKYCY1HF103Z 38- 82 31- 19 RTRNZ0499PACT VCKYPU1HB102K 38- 83 RTRNZ0617PANT 38- 84 " RTRNZ0618PANT " 38- 85 RTRNZ0652PACD VCKYTQ1HF104Z 38- 86 RUNTK0001YSZZ VCKYTV1EB104K RVR-M0385PAZZ 38- 88 VCKYTV1HB102K VCKYTV1HB223K...
Page 186 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK VRD-ST2CD101J VRS-TP2BD432J 38-121 37-129 VRD-ST2CD103J VRS-TP2BD472J 38-122 37-130 VRD-ST2CD104J 38-123 VRS-TS2AD000J 30- 15 VRD-ST2CD105J VRS-TS2AD100J 38-124 VRD-ST2CD122J VRS-TS2AD101J 38-125 32- 16 VRD-ST2CD124J VRS-TS2AD102J 38-127 32- 17 VRD-ST2CD153J 38-128 VRS-TS2AD103J...
Page 187 DM-1505 PRICE PART PRICE PART PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK XEBSE30P12000 16- 40 " 18- 31 XEBSE30P14000 2- 22 XEBSE40P12000 " 11- 21 " 15- 30 " 16- 35 " 16- 45 " 17- 15 "...
Page 188 DM-1505 COPYRIGHT C 1999 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

Dm-1500 Dm-1505

Sharp DM-1505 - B/W Laser Printer Service Manual

Quick Links

Related Manuals for Sharp DM-1505 - B/W Laser Printer

Summary of Contents for Sharp DM-1505 - B/W Laser Printer

This manual is also suitable for:

Table of Contents