Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAM SELECTION
START/RESUME BUTTON
BUTTON
Push this button to start the selected program: the
Push "Programs" button
indicator lights up and goes off at the end of the program.
(repeatedly) until the indicator
When the door is opened during a washing cycle, the
of the required program lights
cycle is temporarily paused: the Start indicator blinks.
up (see "Table of programs"
To resume the cycle push Start button and close
below).
the door within 3 seconds.
Table of programs
P
Programs
1
AutoSensor 50-65°C
2
Quickwash
45°C
3
2)
50°C
Eco
4
3)
Antibacterial
5
Intensive
70°C
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance's automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
"nk_customer@whirlpool.com".
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697
standard of November 2001.
(see at right for options description)
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute
(0:01 is shown into the display).
If pressed when the dishwasher is switched off,
it drains any possible liquids from dishwasher
(1 minute process).
Available
Loading instructions
options
Delay
Recommended program for routine
Multizone
washes, with dried-on food (e.g. EN
Power Clean
50242).
Delay
Lightly soiled crockery, with no
Multizone
dried-on food.
Delay
Normally soiled crockery.
Multizone
Energy-saving program.
Power Clean
Normally or heavily soiled crockery,
Delay
with additional antibacterial wash.
Multizone
Programme interruption (e.g. due to
Power Clean
door opening) can compromise
elimination of germs.
Delay
Recommended program for heavily
Multizone
soiled crockery, especially suitable
Power Clean
for pans and saucepans.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
WASH TIME DISPLAY
Consumption
Indicated the cycle duration and the remaining time (h:min). With "Delayed start" selected it indicates
Deter-
the time remaining until program start (h.00) - below 1h (0:min).
If "Fx Ey" messages appears on the display, see page 6 - chapter "What to do if...".
gent
1)
Litres
kWh
Minutes
MULTIZONE
Allows you to choose the washing
X
7-14 1.00-1.60
70-155
zones. Press this button (repeatedly)
to select the wash zones:
X
11.0
0.80
30
X
12.0
1.05
165
X
13.0
1.50
115
POWER CLEAN
Thanks to the additional power jets
this option provides a more intensive
X
14.0
1.55
155
and powerful wash in the lower rack,
in the specific area. This option is
recommended for washing pots and
casseroles (see page 4). Press this
button to activate Power Clean (the
indicator lights up).
ADG 7800
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30
SECONDS IF NO CYCLE HAS STARTED.
both racks
only lower rack
TABLET SETTING
This setting allows to
optimize the cycle
only upper rack
performances according
the type of detergent
- indicator lits
used. Push the Tablet
button for 3 seconds (until
the indicator lights up) if
you are using the
combined detergents in
tablet (rinse aid, salt and
detergent in 1 dose). If you
are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
Chart
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
DELAYED START
BUTTON
Push the button
(repeatedly) to delay the
start of the program.
Adjustable from 1 to 24
hours. With each press of
the button, the delayed
start indicator increases
by one hour and after 24
restarts from 0. Then
press the START button.
The dishwasher will start
after the set time.
5019 396 01993
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 7800
Summary of Contents for Whirlpool ADG 7800
- Page 1 EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. 3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 ADG 7800 5019 396 01993 standard of November 2001.
-
Page 2: First Time Use
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. before the first wash or if water - The current water hardness setting will be visible on the display. -
Page 3: Daily Use
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Visual The rinse aid dosage can be indicator adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). -
Page 4: How To Load The Racks
How to load the racks How to load UPPER RACK How to adjust upper rack height (if available). (depending on the model) B - Cutlery basket - half: can be placed in the upper rack A - Adjustable flaps: in horizontal position for It could be useful to lift up the upper rack to have when the “Half load/Multizone”... -
Page 5: Maintenance And Care
Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. - Page 6 What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking Error number “E”y - blinking...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - Water too hard.
-
Page 8: Precautions And General Recommendations
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...