Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAM SELECTION
START/RESUME BUTTON
BUTTON
Push this button to start the selected program: the
Push "Programs" button
indicator lights up and goes off at the end of the
(repeatedly) until the indicator
program. When the door is opened during a
of the required program lights
washing cycle, the cycle is temporarily paused: the
up (see "Table of programs"
Start indicator blinks.
below).
To resume the cycle push the Start button and
close the door within 3 seconds.
Table of programs
P
Programs
1
AutoSensor 50-65°C
2
Quickwash
45°C
3
2)
50°C
Eco
4
3)
Antibacterial
5
Intensive
70°C
1)
Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional
options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the
appliance's automatic calibration system.
2)
Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information
on the EN/Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3)
The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
(see at right for options description)
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter "What to do if ...".
Available
Loading instructions
options
Recommended program for routine
Delay
washes, with dried-on food (e.g.
EN 50242).
Lightly soiled crockery, with no
Delay
dried-on food.
Normally soiled crockery.
Delay
Energy-saving program.
Normally or heavily soiled crockery,
with additional antibacterial wash.
Delay
Program interruption (e.g. due to
door opening) can compromise
elimination of germs.
Recommended program for heavily
Delay
soiled crockery, especially suitable
for pans and saucepans.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Options and display description
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
Consumption
Deter-
gent
1)
Litres
kWh
Minutes
X
7-14
1.00-1.60
70-155
X
11.0
0.80
30
X
12.0
1.05
165
TABLET SETTING
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator
X
13.0
1.50
115
lights up) if you are using the combined detergents in
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent,
X
14.0
1.55
155
the Tablet indicator on the control panel has to be off.
ADG 7580
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
Chart
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
DELAYED START
BUTTON
The wash cycle can be
programmed to start
after 2, 4 or 8 hours.
Then press the Start
button. The wash
program will start after
the set time.
5019 396 01958
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 7580
Summary of Contents for Whirlpool ADG 7580
- Page 1 5019 396 01958 on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
-
Page 2: First Time Use
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. before the first wash or if water - Programs LEDs will indicate the water hardness setting. -
Page 3: Daily Use
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Visual The rinse aid dosage can be indicator adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). -
Page 4: How To Load The Racks
How to load the racks How to load UPPER RACK How to adjust upper rack height (if available). (depending on the model) B - Cutlery basket - half: can be placed in the upper rack A - Adjustable flaps: in horizontal position for It could be useful to lift up the upper rack to have when the “Half load/Multizone”... -
Page 5: Maintenance And Care
Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. - Page 6 What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - Water too hard.
-
Page 8: Precautions And General Recommendations
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...