DeWalt DWE4357 Original Instructions Manual
Hide thumbs
Also See for DWE4357:
- Original instructions manual (200 pages) ,
- Service manual (6 pages) ,
- Original instructions manual (37 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DWE4357
Summary of Contents for DeWalt DWE4357
- Page 1 DWE4347 DWE4357 DWE4369 Final Page size: A5 (148mm x 210mm)
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A DWE4357, DWE4369 Fig. B Fig. C...
- Page 4 Fig. E Fig. D Fig. F Fig. G...
-
Page 5: Technical Data
English SMALL ANGLE GRINDERS DWE4347, DWE4357, DWE4369 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data DWE4347 DWE4357... -
Page 6: Definitions: Safety Guidelines
English 2) Electrical Safety a ) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Vice President of Engineering, PTE-Europe Unmodified plugs and matching outlets will reduce risk of Director Engineering electric shock. - Page 7 English h ) Do not let familiarity gained from frequent use of b ) Operations such as polishing are not recommended tools allow you to become complacent and ignore to be performed with this power tool. Operations for tool safety principles. A careless action can cause severe which the power tool was not designed may create a injury within a fraction of a second.
-
Page 8: Kickback And Related Warnings
English k ) Position the cord clear of the spinning accessory. If snag the rotating accessory and cause loss of control you lose control, the cord may be cut or snagged and your or kickback. hand or arm may be pulled into the spinning accessory. e ) Do not attach a saw chain woodcarving blade or l ) Never lay the power tool down until the accessory toothed saw blade. -
Page 9: Using An Extension Cable
English Electrical Safety d ) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and The electric motor has been designed for one voltage only. carefully re-enter the cut. The wheel may bind, walk up Always check that the power supply corresponds to the voltage or kickback if the power tool is restarted in the workpiece. - Page 10 Guard for an extended amount of time it will shut-off and require the Slider switch switch to cycle to restart. Variable speed dial (DWE4357, DWE4369) Electronic Soft Start Guard release lever This feature limits the initial start up momentum, allowing the LED Indicator speed to build up gradually over a 1 second period.
- Page 11 English Adjusting and Mounting Guard (Fig. C, D) 4. To position the guard: One-touch : Rotate the guard clockwise into the CAUTION: Turn unit off and unplug the tool before desired working position. Press and hold the guard release making any adjustments or removing or installing lever ...
-
Page 12: Prior To Operation
English WARNING: Proper guard must be reinstalled for grinding inspecting and installing an accessory, position yourself and wheel, cutting wheel, sanding flap disc, wire brush or bystanders away from the plane of the rotating accessory wire wheel applications after sanding applications and run the power tool at maximum no-load speed for one are complete. - Page 13 Variable Speed Dial (Fig. A) instructions in this manual. WARNING: Metal dust build-up. Extensive use of flap DWE4357, DWE4369 discs in metal applications can result in the increased WARNING: Regardless of the speed setting, the rated potential for electric shock. To reduce this risk, insert an...
-
Page 14: Cutting Metal
English Precautions To Take When Working on a NOTICE: Edge grinding/cutting with a Type 27 wheel must be limited to shallow cutting and notching—less Painted Workpiece than 13 mm in depth when the wheel is new. Reduce the 1. Sanding or wire brushing of lead based paint is NOT depth of cutting/notching equal to the reduction of the RECOMMENDED due to the difficulty of controlling the wheel radius as it wears down. - Page 15 English Rough Grinding Optional Accessories never use a cutting disc for roughing. WARNING: Since accessories, other than those offered Always use the guard type 27. by D WALT, have not been tested with this product, use of such accessories with this tool could be hazardous. The best roughing results are achieved when setting the To reduce the risk of injury, only D WALT recommended...
- Page 16 English LED Guide The section provides a list of possible LED blink patterns, their causes and corrective solutions. The user or maintenance personnel can perform some corrective actions, and others may require the assistance of qualified D WALT technician or your dealer.
- Page 17 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded nut Type 27 guard Wire wheel...
- Page 18 English Grinding and Cutting Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Threaded clamp nut Type 27 Guard...
- Page 20 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)