Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZDT24004FA
Summary of Contents for Zanussi ZDT24004FA
- Page 1 User Manual GETTING STARTED? EASY. ZDT24004FA EN User Manual Dishwasher...
-
Page 2: Safety Information
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. -
Page 3: Safety Instructions
Put the cutlery in the cutlery basket with the sharp ends • pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to •... - Page 4 WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. • Do not sit or stand on the open door. •...
-
Page 5: Easy Start
EASY START On/off button Indicators Programme buttons Delay button INDICATORS Indicator Description End indicator. XtraDry indicator. Salt indicator. It is always off while the programme operates. BEAM-ON-FLOOR The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. •... - Page 6 PROGRAMMES Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Normal soil • Prewash 0.921 Crockery and • Wash 50 °C cutlery • Rinses • • Prewash 45 - 160 0.7 - 1.5 7 - 12 Crockery, cut- •...
- Page 7 • Bring the appliance back to the programme The indicators: , and selection mode. start flashing. To CANCEL: As the appliance stores the saved settings, there is no need to configure it before every cycle. Press and hold simultaneously until the control panel indicates the appliance ADJUSTING THE WATER SOFTENER is in the programme selection mode.
-
Page 8: Before First Use
By default, AirDry is activated with all programmes 2. Press to change the setting. 3. Press on/off to confirm and save the setting. excluding (if applicable), but it is possible to deactivate it. HOW TO DEACTIVATE AIRDRY Make sure the appliance is in user mode. AirDry improves the drying results with less energy 1. -
Page 9: Daily Use
ADDING RINSE AID The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. Fill the rinse aid dispenser when the indicator (A) becomes clear. DAILY USE 1. Open the water tap. 3. - Page 10 SETTING AND STARTING A PROGRAMME The AUTO OFF function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme The indicator is on.
-
Page 11: Hints And Tips
HINTS AND TIPS GENERAL the tableware, we recommend that you use the tablets with long programmes. The following hints will ensure optimal cleaning and • Do not use more than the correct quantity of drying results in daily use and also help to protect detergent. -
Page 12: Care And Cleaning
• The programme is applicable for the type of load 2. First remove items from the lower basket, then and for the degree of soil. from the upper basket. • The correct quantity of detergent is used. At the end of the program water can UNLOADING THE BASKETS still remain on the sides and on the door of the appliance. -
Page 13: Troubleshooting
• To maintain the performance of your appliance Follow carefully the instructions on the at its best, we recommend to use monthly a packaging of the product. specific cleaning product for dishwashers. TROUBLESHOOTING If the appliance does not start or it stops during With some problems the end indicator flashes operation, before you contact an Authorised intermittently indicating a malfunction. - Page 14 Problem and alarm code Possible cause and solution The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. Small leak from the appliance door. • The appliance is not levelled.
- Page 15 Problem Possible cause and solution There are whitish streaks or blu- • The release quantity of rinse aid is too much. Adjust the rinse ish layers on glasses and dishes. aid level to a lower level. • The quantity of detergent is too much. There are stains and dry water •...
-
Page 16: Technical Information
Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550 Voltage (V) 220 - 240 Electrical connection Frequency (Hz) Water supply pressure Min. - Page 20 WWW.ZANUSSI.COM/SHOP...