Related Manuals for NEC NP02LK
Summary of Contents for NEC NP02LK
- Page 1 Support Kit Handling Instructions Model NP02LK サポートキット取扱説明書 NP02LK 型名 支撑套件操作说明书 NP02LK 型号...
-
Page 2: Table Of Contents
CONTENTS Introduction ..............3 CAUTION .................4 Things to prepare ............4 Included items ...............5 Preparation ..............6 How to install the support kit ........7 Adjusting the vertical position of a projected image (Lens shift) ....14 Adjusting the focus ...........15 Adjusting the tilt ............15 Tilt adjustment during portrait projection ..16 目次... -
Page 3: Introduction
( English ) Introduction This is the handling instructions of the support kit for the fixed focus lens NP44ML. This document describes how to attach the support kit and how to adjust it. For USA: About the procedures for mounting the lens unit, please refer to the projector User’s Manual. For other countries: To mount the lens unit and the support kit, consult your dealer. -
Page 4: Caution
CAUTION • After installing the lens unit, be sure to secure it to the projector using the support kit. Fail- ure to do so could cause the lens unit to fall, resulting in injury. • Power off the projector and unplug the power cord before installing the lens unit and the support kit. Things to prepare • Phillips head screwdriver • For ceiling mount or portrait position, a mounting bracket with sufficient strength to support the combined weight of the projector, the lens unit, and the support kit 注意... -
Page 5: Included Items
Included items Support bracket Screw ( M4×10 ) 8 pcs Screw (M4×20) 1 pc Adapter 同梱品 サポート金具 ネジ （M4 × 10）８本 ネジ （M4 × 20）1 本 アダプター 内含物品 支撑支架 螺钉 (M4×10) ８个 ... -
Page 6: Preparation
Preparation Return the projector lens position to the home position without the lens mounted. For details on connecting the power cord and turning on/off, refer to the projector User’s Manual. Connect the power cord to the projector, and then press the (POWER) button to turn on the power. Press and hold the ZOOM/L-CALIB button for 2 seconds or longer. ... -
Page 7: How To Install The Support Kit
How to install the support kit 1. Turn over the projector. Lay down the projector cabinet upside down on a table with soft cloth laid. While doing this, align the front of the projector with the end of the table. CAUTION • For moving the projector, make sure you have at least two people. Attempting to move the projector alone could result in back pain or other injuries. - Page 8 2. Fix the adapter to the lens unit. As describing on the illustration, put the adapter on the lens unit whose protrusions meet with the screw holes on the adapter and fasten them by 2 screws (M4×10). NOTE: Do not touch the glass on the lens unit. 2.
- Page 9 3. Adjust the tilt of the lens unit. Adjust the focus balance at the periphery of the projected image. For table use: Move the tilt lever to the “+” position. For ceiling use: Move the tilt lever to the “-“ position. For other uses: Move the tilt lever to the center (around “T” letter). 3. レンズユニットのチルト調整を行う 投写画面の周辺部分のフォーカスバランスを調整します。 テーブルに設置する場合：チルトレバーを＋の位置に合わせます。 天吊りで設置する場合：チルトレバーを−の位置に合わせます。 上記以外で設置する場合：チルトレバーを中央（T の文字付近）に合わせます。 3. 调整镜头单元的倾斜度。 调整投影图像外围的聚焦平衡。 对于在桌上使用 ： 将倾斜杆移动到 “+”位置。 对于在天花板上使用 ： 将倾斜杆移至 “ - ”位置。 对于其他用途...
- Page 10 4. Mount the lens unit on the projector and adjust the lens position According to the instructions on the projector manual, mount the lens unit onto the projec- tor. Connect the power cord to the projector and power it on. ...
- Page 11 5. Adjust the support bracket. Loosen the wing nut on the support bracket and pull out the L-shaped metal fitting. Rotate the dial to align its hole with its top position. 6. Fix the support bracket to the projector. As shown on the illustration, place the support bracket and use four screws (M4×10) to tighten them.
- Page 12 ピン 插针 7. Connect the support bracket to the adapter. Move the L-shaped metal fitting of the support bracket to meet with the adapter, and insert the adapter pin into the hole of dial. When doing this, make sure that the L-shaped metal fitting and the adapter are so securely fixed that the adapter pin can be seen through the hole of dial.
- Page 13 8. Tighten a screw to fix the support bracket and the adapter. Tighten two screws (M4×10) to fix the L-shaped metal fitting and the adapter. Tighten the wing nut. This completes mounting the support kit. After installing the projector, connect the power cord and video cables, and then turn on the projector. Finally, adjust various items.
-
Page 14: Projected Image (Lens Shift)
Wing nut Screw 蝶ナット ネジ 蝶形螺母 螺钉 Adjusting the vertical position of a projected image (Lens shift) To shift the lens, loosen the wing nut and screws that were fastened in step 8 for the support kit installation procedure. To adjust the horizontal direction, loosen the wing nut To adjust the vertical direction, loosen the two screws For details on lens shift operations, refer to the projector User’s Manual. -
Page 15: Adjusting The Focus
Adjusting the focus Refer to the projector User’s Manual. Adjusting the tilt Loosen the two screws that were tightened in step 8 for the support kit installation pro- cedure. Use your hand or a Phillips head screw driver to rotate the dial of the support bracket, and then adjust the vertical focus balance of the projected image. -
Page 16: Tilt Adjustment During Portrait Projection
Screw insertion port ネジ挿入口 螺钉插入端口 Wing nut 蝶ナット 蝶形螺母 Tilt adjustment during portrait projection If the lens unit tilts downward when portrait orientation is used with the projector installed ver- tically, follow the procedure below to adjust the tilt. * The stand that supports the projector is omitted in the drawings for clarity. ... - Page 17 © NEC Display Solutions, Ltd. 2020 Printed in China 7N8R0561...