Bosch DSA E Series Installation Manual
Iscsi disk arrays
Hide thumbs
Also See for DSA E Series:
- Installation manual (54 pages) ,
- Installaton manual (50 pages) ,
- Quick installation manual (30 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch DSA E Series
Summary of Contents for Bosch DSA E Series
- Page 1 E2600 DSA E-Series iSCSI Disk Arrays Installation Manual...
-
Page 3: Table Of Contents
Things to Know – General Installation of Drive Trays with the E2600 Controller-Drive Tray For Additional Information on Drive Tray Installation Procedure – Installing the DE1600 Drive Trays Procedure – Installing Drives in the DE1600 Drive Trays Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 4 Upgrading or Replacing a Host Interface Card in the Controller-Drive Tray 16.1 Removing the Host Interface Card from the Controller-Drive Tray 16.2 Installing the Host Interface Card in the Controller-Drive Tray - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 5 Reinstalling the Controller Canister in the E2600 Controller-Drive Tray 19.5 Turning On Power to the Controller Canisters in the E2600 Controller-Drive Tray Regulatory Compliance Statements 20.1 FCC Radio Frequency Interference Statement 20.2 Laser Products Statement Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 6: Safety Precautions
Attach the stability foot before moving the cabinet. If you do not attach the stability foot, the cabinet might become unstable, or it might fall. This problem is most likely to occur when the cabinet is moved along inclined surfaces or over uneven surfaces. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 7 60ºC (140ºF), crush or puncture, short circuit external contacts, or dispose of in fire or water. Use LSI recommended charger only. Replace only with original LSI batteries. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 8 An empty tray weighs approximately 56.7 kg (125 lb). Three persons are required to safely move an empty tray. If the tray is populated with components, a mechanized lift is required to safely move the tray. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 9: Caution Notices
As you push the canister into the slot, ensure that your fingers are not pinched between the lever and the canister. The lever automatically moves toward the closed position as the canister is pushed into its slot. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 10 This equipment is designed to permit the connection of the DC supply circuit to the earthing conductor at the equipment. CAUTION! Possible hazard exists Do not remove more than one canister from the enclosure while power to the enclosure is turned on. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 11: Preparing For An E2600 Controller-Drive Tray Installation
Two 6-Gb/s host connectors, in addition to one of the following host interface cards: – Two 6-Gb/s SAS connectors – Four 1-Gb/s iSCSI connectors – Two 10-Gb/s iSCSI connectors – Four 8-Gb/s FC connectors 8-GB battery backup. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 12: Key Terms
Before you start installing the controller-drive tray, you must have installed the cabinet in which the controller-drive tray will be mounted. Use the tables in this section to verify that you have all of the necessary items to install the controller-drive tray. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 13: Basic Hardware
Gigabit Ethernet switch (optional) – Host with Fibre Channel host bus adapters (HBAs) (optional) – Host with iSCSI HBAs (optional) or a network interface card (optional) – Host with SAS HBAs (optional) Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 14 For the differences between the fiber-optic cables and the copper Fibre Channel (FC) cables, see Section 2.2.3 Things to Know – SFP Transceivers, Fiber-Optic Cables, Copper Cables, and SAS Cables, page 17 - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 15 Section 2.2.3 Things to Know – SFP Transceivers, Fiber-Optic Cables, Copper Cables, and SAS Cables, page 17 Ethernet cable This cable is used for out-of-band storage array management and for 1-Gb/s iSCSI connections. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 16 SANtricity ES Storage Manager Installation – SANtricity ES Storage Manager software and documentation. – To access product documentation, use the documentation map file, doc_launcher.html, which is located in the docs directory. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 17: Tools And Other Items
SAS cables with a SFF-8088 Connector. NOTICE! Your SFP transceivers and cables might look slightly different from the ones shown. The differences do not affect the performance of the SFP transceivers. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 18 Fiber-Optic Cable Figure 2.2 1-Gb/s iSCSI Cable Connection Active SFP Transceiver Copper Cable with RJ-45 Connector Figure 2.3 Copper Fibre Channel Cable Connection Copper Fibre Channel Cable Passive SFP Transceiver - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 19: Things To Know - Taking A Quick Glance At The Hardware
Figure 2.5 E2600 Controller-Drive Tray with 12 Drives – Front View End Cap Standby Power LED End Cap Power LED End Cap Over-Temperature LED End Cap Service Action Required LED End Cap Locate LED Drive Canister Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 20 Power-Fan Canister Standby Power LED Power-Fan DC Power LED Power-Fan Service Action Allowed LED Power-Fan Service Action Required LED Power-Fan AC Power Connector and Switch Power-Fan DC Power Connector and Switch - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 21 Host Interface Card Link 4 Up LED Host Interface Card Link 4 Active LED SFF-8088 Host Interface Card Connector 4 ESM Expansion Fault LED ESM Expansion Active LED Expansion SFF-8088 Port Connector Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 22 Figure 2.10 E2600 Right-Rear Subplate with a 1-Gb iSCSI Host Interface Card Host Interface Card Link 3 Up LED Host Interface Card Link 3 Active LED iSCSI Host Interface Card Connector 3 - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 23 Host Interface Card Link 4 Up LED Host Interface Card Link 4 Active LED iSCSI Host Interface Card Connector 4 ESM Expansion Fault LED ESM Expansion Active LED Expansion SFF-8088 Port Connector Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 24 Not all controller-drive trays are shipped with pre-populated drives. System integrators, resellers, system administrators, or users of the controller-drive tray can install the drives. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 25 Expansion Port SFF-8088 Connector Power-Fan Canister Power Connector Power Switch ESM B Canister Figure 2.15 DE1600 Drive Tray with DC Power Option – Rear View ESM A Canister Host Connector 1 Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 26 (item 4 below) from the power supplies. Figure 2.16 Power cable Supply (Negative), Brown Wire, -48 VDC Return (Positive), Blue Wire Ground, Green/Yellow Wire DC Power Connector - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 27: Installing And Configuring The Switches
SANtricity ES Storage Manager Version 10.77. Table 3.1 Supported Switches Vendor Model Fibre Channel iSCSI Brocade 200E 3200 3800 3900 3950 12000 3850 3250 24000 4100 48000 5000 5100 5300 7500 7800 FCOE Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 28 If required, make the appropriate configuration changes for each switch that is connected to the storage array. Refer to the switch’s documentation for information about how to install the switch and how to use the configuration utilities that are supplied with the switch. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 29: Procedure - Installing And Configuring Switches
See Section 4 Installing the Host Bus Adapters for the E2600 Controller-Drive Tray, page 30 PowerConnect See Section 4 Installing the Host Bus Adapters for the E2600 Controller-Drive Tray, page 30 Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 30: Installing The Host Bus Adapters For The E2600 Controller-Drive Tray
Most of the HBAs, as shipped from the vendor, require updated firmware and software drivers to work correctly with the storage array. For information about the updates, refer to the website of the HBA vendor. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 31: Procedure - Installing Host Bus Adapters
Vendor x, Model y (dual port) 37:38:39:30:31:32:33:32 37:38:39:30:31:32:33:33 Vendor a, Model y (dual port) 42:38:39:30:31:32:33:42 42:38:39:30:31:32:33:44 ICTFINANCE Vendor a, Model b (single port) 57:38:39:30:31:32:33:52 Vendor x, Model b (single port) 57:38:39:30:31:32:33:53 Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 32: Installing The E2600 Controller-Drive Tray
Figure 5.1 Airflow Direction Through and Clearance Requirements for the E2600 Controller-Drive Tray with 12 Drives 76-cm (30-in.) clearance in front of the cabinet 61-cm (24-in.) clearance behind the cabinet - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 33 Not all controller-drive trays are shipped with pre-populated drives. System integrators, resellers, system administrators, or users of the controller-drive tray can install the drives. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 34 The rear of the controller-drive tray slides into the slots on the mounting rails. Figure 5.3 Securing the E2600 Controller-Drive Tray with 12 Drives to the Cabinet Screws Mounting Holes - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 35: Connecting The E2600 Controller-Drive Tray To The Hosts
In configurations where a HIC does not exist, the space is covered with a blank faceplate. Figure 6.1 Host Channels on the Controllers – Rear View Standard Host Connectors Host Interface Card (HIC) Connectors (SAS in this Example) SAS Expansion Connector Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 36: Procedure - Connecting Host Cables On An E2600 Controller-Drive Tray
Plug the other end of the cable either into an HBA in the host (direct topology) or into a Note:switch (fabric topology). Note: The SAS host interface does not support a switch topology. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 37: Example Cabling Patterns
Figure 6.2 Direct Topology – One Host Connected to a SingleController Host HBA 1 or NIC 1 HBA 2 or NIC 2 Host Port 1 Host Port 2 Controller A Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 38: Direct Topology - Two Hosts Connected To A Single Controller
Figure 6.3 Direct Topology – Two Hosts Connected to a Single Controller Host HBA 1 or NIC 1 HBA 2 or NIC 2 Host Port 1 Host Port 2 Controller A - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 39: Switch Topology - Two Hosts Connected To A Single Controller Through A Switch
Figure 6.4 Switch Topology – Two Hosts Connected to a Single Controller Through a Switch Host HBA 1 or NIC 1 HBA 2 or NIC 2 Host Port 1 Host Port 2 Controller A Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 40: Direct Topology - One Host And A Dual Controller-Drive Tray
Figure 6.5 Direct Topology – One Host and a Dual Controller-Drive Tray Host HBA 1 or NIC 1 HBA 2 or NIC 2 Host Port 1 Host Port 2 Controller A Controller B - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 41: Direct Topology - Two Hosts And A Dual Controller-Drive Tray For Maximum Redundancy
Figure 6.6 Direct Topology – Two Hosts and a Dual Controller-Drive Tray for Maximum Redundancy Hosts HBA 1 or NIC 1 HBA 2 or NIC 2 Host Port 1 Host Port 2 Controller A Controller B Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 42: Mixed Topology - Two Hosts And A Dual Controller-Drive Tray
Figure 6.7 Mixed Topology – Two Hosts and a Dual Controller-Drive Tray Hosts HBA 1 or NIC 1 HBA 2 or NIC 2 Host Port 1 Host Port 2 Controller A Controller B - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 43: Mixed Topology - Three Hosts And A Dual Controller-Drive Tray
Figure 6.8 Mixed Topology – Three Hosts and a Dual Controller-Drive Tray Host 1 HBA 1 or NIC 1 HBA 2 or NIC 2 Host 2 Host 3 Host Port 1 Host Port 2 Controller A Controller B Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 44: Installing The Drive Trays For The E2600 Controller-Drive Tray Configurations
If the top half of the cabinet is too heavy for the bottom half, the cabinet might fall and cause bodily injury. Always install a component in the lowest available position in the cabinet. You can install the drive tray into an industry standard cabinet. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 45 If you are installing the mounting rails above an existing tray, position the mounting rails directly above the tray. – If you are installing the mounting rails below an existing tray, allow 8.8-cm (3.5-in.) vertical clearance for the drive tray. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 46 Attach the mounting rails to the cabinet. Make sure that the adjustment screws on the mounting rail are loose so that the mounting rail can extend or contract as needed. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 47 The front flange of each mounting rail has two alignment spacers. The alignment spacers are designed to fit into the mounting holes in the cabinet. The alignment spacers help position and hold the mounting rail. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 48 The rear edge of the drive tray sheet metal fits into the clip on the mounting rail. – The holes in the drive tray sheet metal for the rear hold-down screws align with the captured nuts in the side of the mounting rails. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 49 Insert one M5 screw through the bottom hole of a flange on the drive tray so that the screw goes through the cabinet rail and engages the bottom captured nut in the mounting rail. Tighten the screw. – Repeat the same for the second flange. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 50 Put the top of the end cap on the hinge tab that is part of the drive tray mounting flange. – Gently press on the bottom of the end cap until it snaps into place over the retainer on the bottom of the drive tray mounting flange. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 51: Procedure - Installing Drives In The De1600 Drive Trays
To avoid exceeding the functional and environmental limits, install only drives that have been provided or approved by the original manufacturer. Drives might be shipped but not installed. System integrators, resellers, system administrators, or users can install the drives. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 52 Figure 7.8 Installing a Drive in the DE1600 Drive Tray Drive Handle Install the second drive beneath the first drive. Install the other drives from top to bottom and then from left to right. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 53: Connecting The E2600 Controller-Drive Tray To The Drive Trays
Each DE1600 drive tray can contain a maximum of twelve 8.89-cm (3.5-in.) drives. – The ESMs on the DE1600 drive tray contain two sets of In connectors and one set of Out connectors. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 54: Things To Know - Drive Tray Cabling Configurations - Simplex System
Loss of a drive tray that has a second drive tray connected to it means that you cannot access the second drive tray. Figure 8.3 Controller-Drive Tray Above the Drive Tray - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 55: Things To Know - Drive Tray Cabling Configurations - Duplex System
With tray loss protection, if one drive tray cannot be accessed, you still have access to the remaining drive trays. Figure 8.4 Controller-Drive Tray Above the Drive Tray Figure 8.5 Controller-Drive Tray Between Two Drive Trays Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 56 | Connecting the E2600 Controller-Drive Tray to the Drive Trays E2600 DSA E-Series iSCSI Disk Arrays Figure 8.6 Controller-Drive Tray with Three Drive Trays - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 57: Procedure - Connecting The De1600 Drive Trays
Use the following table to determine the number of SAS cables that you need. Table 8.1 Drive Tray Cables Number of Drive Trays that Number of Cables Required You Plan to Connect to the Controller-Drive Tray Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 58 In the ESM in the next drive tray, insert the other end of the cable into one of the connectors in the left-center of the ESM. Repeat step 6 through step 7 for each drive tray that you intend to add to the storage array. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 59 A. That is, the last drive tray in the chain from controller A must be the first drive tray in the chain from controller Bosch Security Systems Installation Manual...
-
Page 60: Connecting The Ethernet Cables
Connect one end of an Ethernet cable into the Ethernet port 1 on controller A. Connect the other end to the applicable network connection. Repeat step 1 through step 2 for controller B. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 61: Connecting The Power Cords
DC power connector on the same power-fan canister to a different source for additional redundancy. – A two-pole 30-amp circuit breaker is required between the DC power source and the drive tray for over-current and short-circuit protection. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 62: Procedure - Connecting Ac Power Cords
It is not mandatory that the second DC power connection on each of the drive tray’s DC power-fan canisters be connected. The second DC power connection is for additional redundancy only and may be connected to a second DC power bus. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 63 Connect the brown –48 VDC supply wire to the negative terminal. – Connect the blue return wire to the positive terminal. – Connect the green/yellow ground wire to the ground terminal. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 64: Turning On The Power And Checking For Problems
If you see any amber LEDs, make a note of their location. 11.2 Things to Know – LEDs on the E2600 Controller-Drive Tray The following topics provide details on the LEDs found on the E2600 controller-drive tray. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 65 Power Green Power is present. Power is not present. Standby Power Green The controller-drive tray is The controller- in Standby Power mode. drive tray is not in Standby Power mode. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 66 Drive State Drive Power LED Drive Service Action (Green) Required LED (Amber) Power is not applied. Normal operation – The power is turned on, but drive I/O activity is not occurring. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 67 There is a 10BASE-T rate. Connector 2 rate. Link Rate LED Ethernet Green The link is up (the LED The link is not active. Connector 2 blinks when there is Link Active LED activity). Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 68 Cache is active.* Cache is inactive or the controller canister has been removed from the controller-drive tray. * After an AC power failure, this LED blinks while cache offload is in process. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 69 1 Gb/s. Host Interface Green The link is up (LED blinks The link is not active. Card Link 5 when there is activity). Active LED Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 70 DC power is not available. mode, and DC power is available. DC power from the Power-Fan DC Green DC power from the Power power-fan canister is power-fan canister is available. not available. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 71: Things To Know - General Behavior Of The Leds On The E2600 Controller-Drive Tray
Service Action Drive (left LED, no Allowed symbol) You can remove the canister safely. Power-fan See Section 11.6 Things to Know – Controller Service Action Allowed LEDs, page 81 Battery Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 72 Front bezel on the Tray Over- controller-drive The temperature of the drive tray Temperature tray has reached an unsafe condition. The temperature of the drive tray is within operational range. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 73 AC power Power-fan Indicates that the power supply is Note: receiving AC power input. The LED is directly above or below the AC power switch and the AC power connector. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 74: Things To Know - Leds On The De1600 Drive Tray
Things to Know – LEDs on the DE1600 Drive Tray Figure 11.6 LEDs on the Left End Cap Drive Tray Locate LED Drive Tray Service Action Required LED Drive Tray Over-Temperature LED - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 75 The drive tray is not in TrayStandby Standby Power mode. Standby Power mode. Power Figure 11.7 LEDs on the Drive Drive Power LED Drive Service Action Required LED Drive Service Action Allowed LED Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 76 Host Link 2 Active LED Ethernet Link Active LED Ethernet Link Rate LED ESM Expansion Link Fault LED ESM Expansion Link Active LED ESM Service Action Allowed LED ESM Service Action Required LED - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 77 At least one of the four A link error has occurred. Link Active PHYs in the Out port is working, and a link exists to the device connected to the Expansion Out connector. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 78 Power-Fan Service Action Allowed LED Power-Fan Service Action Required LED Power-Fan Input AC Power LED Figure 11.10 LEDs on the DC Power-Fan Canister Standby Power LED Power-Fan Output DC Power LED - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 79: General Behavior Of The Leds On The De1600
Drive Tray Over- Front bezel on the Temperature drive tray The temperature of the drive tray has reached an unsafe condition. The temperature of the drive tray is within operational range. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 80 AC power is not present. DC Power Power-fan canister Regulated DC power from the power canister and the fan canister is present. Regulated DC power from the power-fan canister is not present. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 81: Things To Know - Service Action Allowed Leds
If the Service Action Required (Fault) LED comes on but the Service Action Allowed LED is off for a particular canister, you might need to service another canister first. Check your storage management software to determine the action that you should take. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 82: Things To Know - Sequence Code Definitions For The E2600 Controller-Drive Tray
Table 11.15 Supported Diagnostic Lock-Down Codes on the Seven-Segment Display Diagnostic Code Description – – The firmware is booting. .8, 8., or 88 This ESM is being held in reset by another ESM. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 83 Drive port mapping tables are not detected, which results in a suspended controller state. The start-of-day (SOD) reboot limit has been exceeded, which results in a suspended controller state. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 84: Things To Know - Diagnostic Code Sequences For The E2600 Controller-Drive Tray
The memory size is changed from bad data in the flash drives, which results in a suspended controller state. DE+ L2+ dash+ CF+ Cx + A cache memory diagnostic has been reported failed, which blank- results in a suspended controller state. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 85: Things To Know - Seven-Segment Display For The De1600 Drive Tray
SFP transceiver with the blinking amber LED, and remove it. A non-catastrophic hardware failure has occurred. The ESM is operating in a Degraded state. Suspended The ESM canister is incompatible with the drive tray firmware. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 86: Replacing A Drive In An E2600 Controller-Drive Tray
If a fault is detected, the amber Drive Service Action Required LED is on. If you can safely remove the drive, the blue Service Action Allowed LED is on (Figure 1). - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 87 Put the drive on an antistatic, cushioned surface away from magnetic fields. 97006-01 Figure 12.2 Removing a Drive from and Replacing a Drive in an E2600 Controller-Drive Tray with 12 Drives Drive Handle Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 88 Did this action correct the problem? – Go to step 9. – If the problem has not been resolved, contact a Customer and Technical Support representative. Remove the antistatic protection. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 89 Click the Recovery Guru toolbar button in the Array Management Window, and com- plete the recovery procedure. If the problem has not been resolved, contact a Cus- tomer and Technical Support representative. 13. Create, save, and print a new storage array profile. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 90: Replacing A Controller Canister In The Controller-Drive Tray
If possible, use the storage management software to create, save, and print a new storage array profile. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 91 Push down the two top cover latch buttons that secure the top cover to the new controller canister. – Remove the top cover by sliding it off the rear of the new controller canister. 98014-01 Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 92 Controller Service Action Allowed LED is 98006-08 Figure 13.2 CDE 2600 Controller Service Action LEDs Controller Service Action Allowed LED (Blue) Controller Service Action Required LED (Amber) - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 93 – Using the release levers and your hands, pull the controller canister out of the controller-drive tray. 98013 Figure 13.3 Removing and Replacing a Controller Canister Release Levers Controller Canister Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 94 Figure 13.5 Inserting the Controller Air Blocker into the Open Controller Slot 14. Press down on both of the top cover latch buttons, and slide the top cover to the rear of the controller canister. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 95 Figure 13.6 Controller Cover and Internal Parts Top Cover Latch Buttons 15. If the failed controller canister contains a battery, unscrew the thumbscrew that secures the battery to the controller canister. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 96: Installing A Controller Canister In The Controller-Drive Tray
Insert the battery circuit board that you removed from the failed controller canister by sliding it towards the front of the new controller canister. Tighten the thumbscrew to secure the battery circuit board in the new controller canister card. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 97 If the problem is not resolved, contact your Customer and Technical Support representative. – Go to step 15. 15. Remove the antistatic protection. 16. Create, save, and print a new storage array profile. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 98: Replacing A Controller Battery In The Controller-Drive Tray
Potential degraded performance To prevent degraded performance, do not twist, fold, pinch, or step on the fiber-optic cables. Do not bend the fiber-optic cables tighter than a 5-cm (2-in.) radius. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 99 The controller slot cannot remain open for more than three minutes because of the possibility of overheating the equipment. The controller air blocker fills the controller slot so that the equipment will not overheat. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 100 Figure 14.4 nserting the Controller Air Blocker into the Open Controller Slot 14. Press down on both of the top cover latch buttons, and slide the top cover to the rear of the new controller canister. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 101 Replacing a Controller Battery in the Controller-Drive Tray | en 101 98014-01 Figure 14.5 Controller Canister Top Cover Latch Buttons Top Cover Latch Buttons 15. Unscrew the thumbscrew that secures the failed battery to the controller canister. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 102 The LEDs come on and go off intermittently for approximately 60 seconds (possibly longer). After this time, you are able to discover the controller canister with the new battery by using the storage management software. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 103 If the problem is not resolved, contact your Customer and Technical Support representative. – Go to step 29. 29. Remove the antistatic protection. 30. Create, save, and print a new storage array profile. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 104: Replacing A Power-Fan Canister In The Controller-Drive Tray
If a fault is detected, the amber Power-Fan Service Action Required LED is on. If you can safely remove the power-fan canister, the blue Power-Fan Service Action Allowed LED is - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 105 10. Remove the power-fan canister from the controller-drive tray. – Rotate the latches to disengage the power-fan canister. – Use the latches as handles to pull the power-fan canister out of the controller-drive tray. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 106 18. Complete any remaining Recovery Guru procedures, if needed. 19. Using the LEDs and the storage management software, check the status of all of the trays in the storage array. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 107: Replacing A Dc Power-Fan Canister In The Controller-Drive Tray
If a fault is detected, the amber Power-Fan Service Action Required LED is on. If you can safely remove the power-fan canister, the blue Power-Fan Service Action Allowed LED is Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 108 Ground, Green and Yellow Wire DC Power Connector CAUTION! Electrical grounding hazard This equipment is designed to permit the connection of the DC supply circuit to the earthing conductor at the equipment. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 109 18. Check the Power-Fan Input DC Power LED, the Power-Fan Output DC Power LED, and the Power-Fan Service Action Required LED on the new power-fan canister (see step 6). Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 110 If the problem is not resolved, contact your Customer and Technical Support representative. – Go to step 24. 24. Remove the antistatic protection. 25. Create, save, and print a new storage array profile. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 111: Upgrading Or Replacing A Host Interface Card In The Controller-Drive Tray
To prevent electrostatic discharge damage to the tray, use proper antistatic protection when handling tray components. If possible, use the storage management software to create, save, and print a new storage array profile. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 112 – Unlock and pull out the release levers to release the controller canister. – Using the release levers and your hands, pull the controller canister out of the controller-drive tray. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 113 11. Prepare the controller air blocker by removing it from its packaging and folding it inward at right angles so it is ready to insert into the open controller slot. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 114 14. On the new controller-drive tray canister, press down on both of the top cover latch buttons, and slide the top cover to the rear. Remove the top cover. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 115 Upgrading or Replacing a Host Interface Card in the Controller-Drive Tray | en 115 98014-02 Figure 16.5 Host Interface Card Replacemen Top Cover Latch Buttons HIC Thumbscrews Host Interface Card HIC Interface Connector HIC Subplate Zero Insertion Force (ZIF) Socket Front Bezel Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 116: Installing The Host Interface Card In The Controller-Drive Tray
Make sure that the seven-segment display ribbon cable is still connected to the motherboard connector. If the ribbon cable is not connected, you must lift the center piece of the motherboard connector, and insert the ribbon cable into the motherboard connector. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 117 14. Complete any remaining Recovery Guru procedures, if necessary. 15. Using the LEDs and the storage management software, check the status of all of the trays in the storage array. Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 118 If the problem is not resolved, contact your Customer and Technical Support representative. – Go to step 17. 17. Remove the antistatic protection. 18. Create, save, and print a new storage array profile. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 119: Replacing A Controller Canister And Related Components
Did the Recovery Guru direct you to replace a failed controller canister? – Go to step 3. – Run the Recovery Guru to identify the failed component, and go to step 3. Put on antistatic protection. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 120 If a fault is detected, the amber Controller Service Action Required LED is on. If you can safely remove the controller canister, the blue Controller Service Action Allowed LED is 98006-08 Figure 17.2 E2600 Controller Service Action LEDs - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 121 Unlock and pull out the release levers to release the controller canister. – Using the release levers and your hands, pull the controller canister out of the controller-drive tray. 98013 Figure 17.3 Removing and Replacing a Controller Canister Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 122 Figure 17.5 Inserting the Controller Air Blocker into the Open Controller Slot 14. Press down on both of the top cover latch buttons, and slide the top cover to the rear of the controller canister. Remove the cover. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 123 16. Remove the battery by sliding it towards the rear of the failed controller canister. You will insert this battery into the new controller canister. 17. If Small Form-factor Pluggable (SFP) transceivers are present, record the ports in which they are installed, and remove them. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 124: Replacing The Host Interface Card In The Controller-Drive Tray
HIC. 98014-02 Figure 17.8 E2600 Controller Cover and Internal Parts Top Cover Latch Buttons HIC Thumbscrews Host Interface Card - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 125: Removing The Cache Memory Dimm From And Reinstalling It Into The Controller-Drive Tray
ZIF socket. Then push the ZIF socket closed. 17.3 Removing the Cache Memory DIMM from and Reinstalling It into the Controller-Drive Tray Locate the cache memory DIMM to be removed from the failed controller canister. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 126 Install the cache memory DIMM device in the new controller canister. – Align the cache memory DIMM in the slot. – Gently push down on the cache memory DIMM to seat the pins into the slot. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 127: Removing And Installing The Cache Memory Offload Backup Sd Card
Removing a Controller Battery from and Reinstalling It into the Controller-Drive Tray If a configuration does not have a controller battery, or if you are moving the existing battery into a new controller canister, skip this procedure. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 128: Reinstalling A Controller Canister In The Controller-Drive Tray
Slide the controller canister all the way into the controller-drive tray. Rotate the release levers towards the center of the controller canister to lock that component into place. Reconnect all of the cables that were disconnected when you removed the controller canister. - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 129 If the problem is not resolved, contact your Customer and Technical Support representative. – Go to step 12. 12. Remove the antistatic protection. 13. Create, save, and print a new storage array profile. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 130: Replacing Failed Memory In The E2600 Controller Canister
Put on antistatic protection. Locate the controller canister in which you want to replace the failed cache memory DIMM or the failed cache backup memory device by checking the Controller Service - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 131 – In the Physical Pane, select the controller, and select Advanced >> Recovery >> Place Controller >> Offline. – set controller [(a | b)] availability=offline; Bosch Security Systems Installation Manual - | V2 | 2012.09...
- Page 132 10. Prepare the controller air blocker by removing it from its packaging and folding it inward at right angles so it is ready to insert into the open controller slot (see Figure 18.3). - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 133 Figure 18.4 Inserting the Controller Air Blocker into the Open Controller Slot 12. On the controller canister, press down on both of the top cover latch buttons, and slide the top cover to the rear (see Figure 18.5). Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 134: Cache Memory Dimm Fault Code / Display Error Code Definitions
A component failure has occurred. Cache memory DIMM (x is the location of the cache memory slot). Blank- An end-of-sequence delimiter appears. All segments are off, and the Diagnostic LED is off. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 135: Replacing A Cache Memory Dimm
Pull back on each ejector handle to disengage the cache memory DIMM pins from the slot on the controller card. – Lift the cache memory DIMM out of the slot. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 136: Replacing A Cache Backup Memory Device
Locate the cache backup memory device that you want to replace as described in step 6 in Removing a Controller Canister from the E2600 Controller-Drive Tray on page 3. Locate the cache backup memory device that you want to replace as described in step - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 137: Reinstalling The Controller Canister In The E2600 Controller-Drive Tray
Reconnect the following cables to the appropriate ports on both controller canisters. – Host interface cables – Drive interface cables – Ethernet cables Go to Section 18.5 Bringing the Controller Canister Online, page 138. Bosch Security Systems Installation Manual - | V2 | 2012.09... -
Page 138: Bringing The Controller Canister Online
If the problem is not resolved, contact your Customer and Technical Support representative. – Go to step 7. Remove the antistatic protection. Create, save, and print a new storage array profile. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 139: Upgrading Memory In The E2600 Controller Canisters
If possible, use the storage management software to create, save, and print a current storage array profile. Use the Locate function in the storage management software to identify the controller canisters to upgrade (see Figure 19.1). Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 140 Figure 19.2 Power Supplies in the E2600 Controller-Drive Tray Power-Fan Canister for Controller A Power-Fan Canister for Controller B - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 141 Release Levers Controller Canister 10. On each controller canister, press down on both of the top cover latch buttons, and slide the top covers to the rear (see Figure 19.4). Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 142: Upgrading The Cache Memory Dimm
DIMM in the other controller canister in the E2600 controller- drive tray. You also must increase the capacity of the cache backup memory devices in both controller canisters. Locate the cache memory DIMM (see Figure 19.5). - | V2 | 2012.09 Installation Manual Bosch Security Systems... - Page 143 When these ejector handles are in the vertical position, the cache memory DIMM is fully engaged and is locked in place. Repeat this procedure for the other controller canister. Go to Section 19.3 Upgrading the Cache Backup Memory Device, page 144. Bosch Security Systems Installation Manual - | V2 | 2012.09...
-
Page 144: Upgrading The Cache Backup Memory Device
19.4 Reinstalling the Controller Canister in the E2600 Controller- Drive Tray Reinstall the top covers on both controller canisters by sliding them forward until the top cover latch buttons click. - | V2 | 2012.09 Installation Manual Bosch Security Systems... -
Page 145: Turning On Power To The Controller Canisters In The E2600 Controller-Drive Tray
If the problem is not resolved, contact your Customer and Technical Support repre- sentative. Using the LEDs and the storage management software, check the status of the trays in the storage array. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 146 If the problem is not resolved, contact your Cus- tomer and Technical Support representative. – Go to step 9. Remove the antistatic protection. 10. Create, save, and print a new storage array profile. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 147: Regulatory Compliance Statements
LSI. It is the user’s responsibility to correct interference caused by such unauthorized modification, substitution, or attachment. Bosch Security Systems Installation Manual - | V2 | 2012.09... - Page 148 This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numЩrique de la classЩ A r especte toutes les exigences du RЮglement sur e le matЮriel br ouilleur du Canada. - | V2 | 2012.09 Installation Manual Bosch Security Systems...
- Page 150 Bosch Security Systems Werner-von-Siemens-Ring 10 85630 Grasbrunn Germany www.boschsecurity.com © Bosch Security Systems, 2011...