Advertisement
Quick Links
Multi Pro
Automatic Workman
Model No. 131-3301
This product contains a chemical or chemicals known to the State of California to
Use of this product may cause exposure to chemicals known to the State of California
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
WM Turf Sprayer Finishing Kit
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
to cause cancer, birth defects, or other reproductive harm.
Description
No parts required
Hydraulic motor
Shaft guard
Motor bracket
Flange-head bolt (1/2 x 1-1/2 inches)
Flange nut (1/2 inch)
Anti-rotation bracket
Flange-head bolt (5/16 x 3 inches)
Flat washer
Compression spring
Flange locknut (5/16 inch)
Straight hydraulic fitting (7/8 inch)
Hydraulic hose (1/2 x 17 inches)
Male coupler
Shaft coupler
Woodruff key
Square-head screw
Flange-head bolt (3/8 x 1 inch)
Flange nut (3/8 inch)
No parts required
Register at www.Toro.com.
®
Utility Vehicle
WARNING
CALIFORNIA
Qty.
–
1
1
1
2
2
1
1
1
2
1
2
2
2
1
1
4
2
2
–
Form No. 3389-123 Rev C
Installation Instructions
Use
Prepare the machine.
Prepare the hydraulic motor.
Install the hydraulic motor to the
hydraulic pump.
Install the hydraulic hoses from the
motor to the high-flow system.
Original Instructions (EN)
All Rights Reserved *3389-123* C
Printed in the USA
Advertisement
Related Manuals for Toro 131-3301
Summary of Contents for Toro 131-3301
- Page 1 Multi Pro ® WM Turf Sprayer Finishing Kit Automatic Workman ® Utility Vehicle Model No. 131-3301 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
-
Page 2: Preparing The Machine
Note: Remove the cargo box or flatbed from the vehicle before installing this kit; refer to the Operator’s Manual for the vehicle. Note: For Non-TC models, install the High-Flow Hydraulic Kit before installing this kit; contact your Authorized Toro Distributor about purchasing this kit. - Page 3 Assembling the Fittings and Hoses to the Hydraulic Motor 1. Install a straight hydraulic fitting (5/8 inch) onto the port-A of the hydraulic motor and a straight hydraulic fitting (5/8 inch) onto the port-B of the hydraulic motor (Figure Note: Torque the fittings to 79 to 98 N∙m (58 to 72 ft-lb).
- Page 4 4. Assemble the 90-degree fitting of the other hydraulic hoses onto the straight fitting in port-B of the hydraulic motor (Figure 5) until it is finger tight. Note: You will torque these fittings later; refer to Installing the Hydraulic Motor step 4 Installing the Hydraulic Hoses from the Hydraulic Motor to the High-Flow Hydraulic Ports...
- Page 5 Installing the Hydraulic Hoses from the Hydraulic Motor to the High-Flow Hydraulic Ports No Parts Required Procedure Figure 8 1. Connect the free end of the hydraulic hose Bottom view (hydraulic-motor port-B) that you marked with tape in step Assembling the Fittings and Hoses to 1.
- Page 6 2. Assemble the female quick-connect coupler onto the male hose fitting (Figure 10) of the hydraulic hose (3/8 x 61 inches). 3. Torque the quick disconnect fitting and the hose to 24 Installing the Hydraulic Hoses to 30 N∙m (18 to 22 ft-lb) for the Boom-Lift Cylinders Routing the Hydraulic Hoses Parts needed for this procedure:...
- Page 7 Installing the Hydraulic Hoses 1. Connect the male quick-connect coupler of the hydraulic hose (3/8 x 79 inches) into the female quick-connect coupler of the pressure hose for the boom-lift manifold that you identified in step shown in Figure Figure 13 1.
- Page 8 Figure 14 1. Cap 3. 90° fitting—hydraulic hose (3/8 x 61 inches) 2. T-fitting (hydraulic tube) 4. Hydraulic-oil filter 4. Assemble the 90° fitting of the hydraulic hose (3/8 x 61 inches) to the T-fitting (Figure 14) and torque the swivel nut of the hose to 37 to 45 N∙m (27 to 33 ft-lb).
- Page 9 Installing the Rocker Switch Parts needed for this procedure: Rocker switch Kit wire-harness adapter Procedure Note: Ensure that the control console and the electrical harness are installed; refer to the Installation Instructions for the sprayer. 1. Connect the 3-pin connector of the wire-harness adapter to the 3-socket connector labeled CLOSED Figure 17...
- Page 10 Notes:...
- Page 11 Notes:...